Equipment

The GA-400-N nitrogen generator (hereinafter referred to as the generator) is a modification of the GA-400 nitrogen generator and is designed primarily to work with a storage tank (receiver) in which a certain "reserve" of nitrogen can be created. Unlike the GA-400, the GA-400-H generator has a built-in pressure monitoring system for nitrogen accumulated in the receiver, which puts the generator into "standby" mode when the maximum pressure value is reached in the receiver, and restarts the generator when the pressure drops below the minimum value. This work allows you to reduce energy consumption and increase the service life of the compressor feeding the generator. Technical specifications Volume fraction of nitrogen is not less than 99.5% by volume (including impurities of inert gases — argon, neon, helium) Volume fraction of oxygen is not more than 0.5 % vol. Volume fraction of water vapor is not more than 0.002 % vol.(20 ppm) Maximum nitrogen capacity, with nitrogen pressure in the storage tank below 2 ati, is not less than 400 l/hour (6.66 l/min) Nominal inlet air pressure is 6 ati Maximum allowable inlet air pressure is 8 ati Minimum inlet air pressure is 5.5 ati Compressed air consumption, at nominal inlet pressure and maximum flow rate is no more than 3000 l/h (50 l/min) Factory setting of the maximum pressure value in the storage tank is 3.5± 0.2 ati Factory setting of the minimum pressure value in the storage tank is 2.4 ±0.4 ati Power consumption is not more than 100 VA Overall dimensions, (width x depth x height) are not more than 230x580x680 mm; Weight is not more than 35 kg Working conditions: ambient temperature, C°, from +10 to +35 Electric power supply from single-phase AC mains voltage, V, 220± 10% and frequency, Hz, 50 ± 1 Average full service life is at least 6 years The generator for electrical safety meets the requirements of Class 1, type H according to GOST 12.2.025-76

Design features: Durable ceramic muffle; Closed heaters on four sides of the chamber; Microprocessor temperature controller; Conveniently located control panel and bright LED display; Automatic shutdown of heating when opening the door; Ease of management and control; LED indicators of heater operation and protection operation; Alarm when the current temperature exceeds the limits of the permissible range; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1100 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than 200x110x285 mm Overall dimensions, WxHxD, mm 505x565x655 Rated supply voltage, 220 V Rated power, W 3300

KLM-A532-1-5 laser modules are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.

The multifunctional X-ray diffractometer DRON-8 (8H) with a vertical theta goniometer and the horizontal position of the sample allows X-ray diffraction analysis of the phase composition, structural state and orientation of a wide range of objects of various shapes and sizes.

The product is designed for cleaning materials in a water environment with the addition of alkali at a temperature of up to 90 ° C by mixing in a laminated stream with maintaining the temperature of the liquid and automatic removal of the oil film. The tank is welded from a metal profile and is a rigid power structure. On the inside, U–shaped heating elements are installed to maintain the set temperature. Temperature control is performed by a digital device. The integrity of the heaters is monitored by a standard ammeter. The liquid level maintenance system ensures a constant level of liquid in the tank. When the liquid level in the tank decreases, the liquid is supplied automatically through the built-in valve (optional). To do this, a level sensor is installed in the tank. If the level drops unacceptably, the heating is turned off. A skimmer is installed to remove the oil film. The tank is equipped with a bubbling device. It can be equipped with a circulation pump.

Laboratory heating plate with two heating sections, with the possibility of setting the temperature and heating time, with a large heating surface area. The heating platforms are made of duralumin. The size of the total heating surface: 568x440 mm. Heating temperature of the plate surface: 40-400 oC.

Temperature range, °C (Current +5) ... +105 Accuracy of temperature maintenance, °C ± 1 Temperature setting error, °C ± 1 Power consumption from AC 220 V, no more, 1600 W Number of jobs, pcs 6 The diameter of the workplace, mm 110 Volume of working fluid, l 24 Useful part of the bath / depth, mm 428x300 / 140 Overall dimensions, mm 530x330x220 Weight of the device without liquid is not more than kg 9

The oven (tile) muffle open MIMP-O (hereinafter referred to as the "oven") is designed for heat treatment of samples and laboratory analysis. Technical specifications The furnace operates at ambient temperature from 10 to 35 °C and relative humidity up to 80% at 25 ° C Power consumption- 2500 W Max. operating temperature- 500 ⁰C Dimensions of the working area WxDxH- 2 panels 300x190 mm Dimensions WxDxH- 490x350x160 mm Weight - 16 kg

Description of the cable finder Success KBI-309M • – A traceroute receiver in the form of a monoblock with a frost-resistant LCD display. • – Graphical representation of the route on the device screen. • – Automatic calculation and display of the depth of the communication up to 10 m, as well as the current in the line. Purpose of the cable finder Success KBI-309M • – Search for live electrical cables. • – Search and tracing of underground utilities (gas pipelines, pipelines, power and telephone cables). • – Determination of the occurrence of underground utilities at a depth of up to 10 m. Features of the AP-019M receiver • – Modern digital tracer receiver-monoblock AP-019M. • – The image of the route on the device screen. • – Automatic calculation and display of the depth of communication and current in the line. • – Several options for displaying information on the receiver indicator: "Route", "Graph", "Graph+", "Minimum maximum" and "2-frequencies" allow the operator to use the device's capabilities as efficiently as possible. • – Additional functions when connecting external sensors. • – Wide range of operating frequencies (50(60) / 100(120) / 512 / 1024 / 8192 / 32768 Hz, wide band 40...8000 Hz, radio 8...40 kHz). • – Frost-resistant, working at temperatures up to -30 ° C. • – Menu in two languages (Russian and English).

A trace searching kit for finding underground utilities (cable lines, metal pipelines, and other communications made of conductive materials), as well as the ability to search for places of damage to the external insulation of communications. The kit includes a receiver in the form of a monoblock with a frost-resistant LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line and the most powerful multi-frequency generator in the TECHNO-AC line, with a range of up to 10 km. Connection to the desired route is possible both by contact and contactless method.

Technical specifications: Operating temperature range, °C -25...+100 Accuracy of temperature maintenance, °C ± 0.1 The discreteness of the temperature display, ° C 0.1 Cooling capacity at 20°C, W 520 Pump capacity in the discharge circuit, not less than, l/min 10.5 Volume of working fluid, l 10 The open part of the bath /depth, mm 190x130/200 Power supply, V/Hz 220/50 Power consumption, not more than 3.6 kW Overall dimensions, mm 430x665x460 Weight without working fluid, kg 40

The LOIP LT-408 modification device consists of an immersion thermostat-circulator LOIP LT-400 and a working bath with a small window, which determines the use of LOIP LT-408 mainly for thermostating external systems. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +200 with tap water cooling °C Tvods+5 ...+200 Accuracy of temperature maintenance, °C ± 0.01 The error of setting the set temperature, no more than, ° C ± 0.02 Heater power, W 2200 Pump: max. flow rate, l/min 6...12 pressure, 0.4 bar Bath volume, l 8 The working fluid is water, silicone oil. The open part of the bath / depth, mm dia. 64/200 Overall dimensions, mm 180x335x400 Weight, kg 8,7