Phytotron (Climate Chamber) I-250

According to the requirements of the standards, the cooler is included in the list of equipment for determining humidity with pre-drying. Usually, grain samples after preliminary drying are cooled in the laboratory room to ambient temperature. However, with such cooling, the ambient temperature reaches only the surface layers of the samples, which affects the results of the analyses. The principle of operation of the cooler is based on blowing sample canopies in mesh buckets placed on a stand by a fan rotating at high speed. Advantages: Rapid cooling of samples. Stable moisture distribution. Allows you to significantly improve the accuracy of the results of determining humidity.

The mill provides grinding of agricultural crops according to the current standards regulating methods of determining their quality. Principle of operation: grain is fed into the mill dispenser, where an air-grain mixture is formed, which enters the grinding chamber. The crushed product is separated from the air in the cyclone and collected in a special removable container. After the grain supply is stopped, the air flow ensures self-cleaning of the dispenser and the grinding chamber of the mill. application It is used in the preparation of samples to determine the quantity and quality of gluten, the "drop number" and other indicators of the quality of crops by infrared spectroscopy and other laboratory analysis methods, which require a high degree of grinding of samples. The CALIBRE differs from its predecessor, the BOREY laboratory mill, by a drastic reduction in overall and weight characteristics. An additional advantage of the CALIBRE mill is the reduction in the number of structural elements. So the absence of the door of the grinding unit makes it possible for quick access to carry out work on cleaning the grinding headset. technical specifications: Volume of the receiving funnel, ml 400 Permissible amount of ground product per hour, kg 3 The grinding time of the suspension is 50 gr., from 25-35 The maximum size of the crushed product, mm 12 The diameter of the sieve holes, mm 0.8; 1.0 The speed of rotation of the grinding hammers, rpm 16 500 Minimum mass of the milled product, g 10 The maximum mass of the milled product, g 300 Overall dimensions, mm 400 x 445 x 400 Weight, kg 26 Noise level, dB 70 Power supply Single-phase AC 220 V, 50 Hz Power, W 1050 The response time of the overload protection system, from 2 GENERAL CHARACTERISTICS: 1. Reproducible sample preparation process: The mill is equipped with a sieve with round holes with a diameter of 0.8 mm*, which makes it possible to obtain a finely dispersed product with a stable particle size during grinding. On a separate order, it is possible to complete a sieve with holes with a diameter of 1.0 mm. 2. Quick and easy cleaning The cyclone-exhaust system of the mill provides self-cleaning of the grinding chamber. The ledges and holes in which the ground sample can be collected are minimized. 3. Low noise The vibration and noise insulation system of the CALIBRE mill allows, with considerable power and productivity, to ensure comfortable work of personnel during the working shift. 4. Maximum safety and ease of operation The closed grinding chamber ensures safe operation of the mill. The thermal overload protection system turns off the electric motor when it stops during the grinding process.

The mill provides grinding of grain crops according to the current standards regulating methods of determining their quality. The principle of operation: grain is fed into the mill dispenser, where an air-grain mixture is formed, which enters the grinding chamber. The crushed product is separated from the air in the cyclone and collected in a special removable container. After the grain supply is stopped, the air flow ensures self-cleaning of the dispenser and the grinding chamber of the mill. application It is used in the preparation of samples to determine the quantity and quality of gluten, the "drop number" and other indicators of the quality of crops by infrared spectroscopy and other laboratory analysis methods, which require a high degree of grinding of samples. GENERAL CHARACTERISTICS • High degree of grinding The mill is equipped with a sieve with round holes with a diameter of 0.8 mm*, which makes it possible to obtain a finely dispersed product with a stable particle size during grinding. *on a separate order, it is possible to complete a sieve with holes with a diameter of 1.0 mm • Quick and easy cleaning The ledges and holes in which the ground sample can be collected are minimized. • Low noise The optimized design of the mill body and the door of the grinding chamber with additional noise insulation ensure comfortable work of the staff during the working shift. • Large volume of the container for the ground sample The volume of the container for the ground sample is 1.4 liters. Thanks to this, it is possible to grind samples weighing up to 500 grams, which allows you to obtain more accurate test results and use the ground sample for simultaneous various analyses. • Dust-free grinding A fundamentally new design of the cyclone-container connection for the ground sample eliminates the possibility of dust entering the air. • Easy to operate The ergonomic handle of the retainer allows you to quickly and easily fix the container for the ground sample. technical specifications: Volume of the receiving funnel, 500 ml Permissible amount of ground product per hour, kg 5 The grinding time of the suspension is 50 gr., from 25-35 The maximum size of the crushed product, mm 12 The diameter of the sieve holes, mm 0.8; 1.0 The speed of rotation of the grinding hammers, rpm 16,800 Minimum mass of the milled product, g 10 The maximum mass of the milled product, 500 g Overall dimensions, mm 550 x 520 x 460 Weight, kg 50 Noise level, dB 70 Power supply Single-phase AC 220 V, 50 Hz Power, W 1100 The response time of the overload protection system, from 20

GENERAL CHARACTERISTICS: • Possibility of cleaning and autoclaving of all parts of the grinding set The grinding chamber of the mill and all parts of the grinding set that come into contact with the sample can be easily removed for cleaning and autoclaving, which is an important condition for sample preparation in the determination of GMOs. • Minimal heating of the sample during grinding The special design of the grinding chamber and the use of special knives guarantee minimal heating of the laboratory sample, which eliminates the negative impact on the quality of the extracted DNA. • Grinding with the required quality and homogenization of the sample in one grinding step The ability to select the optimal combination of blade rotation speed, grinding time and automatic rotation of the grinding unit guarantees high-quality, fast grinding and homogenization of samples for various types of samples. • Reproducible grinding results Automation of the grinding process and digital time setting ensure high reproducibility of grinding results. • Easy operation with information display The mill is easy and convenient to operate. Time and grinding mode are set by one button. The information display will show the grinding process parameters. • Grinding of samples with high fat content (up to 55%) The automatic 210° and 90° automatic cycling of the grinding unit, combined with a high grinding speed, minimizes sample heating and oiling of the grinding chamber, which guarantees high-quality, fast grinding and homogenization of samples with a high fat content. 3 grinding chambers are included in the DELIVERY SET of the VYUGA-GMO mill. By separate order it is possible to purchase the required number of grinding chambers.

Implements a thermogravimetric (air-thermal) method for determining the mass fraction of moisture, based on measuring the mass of the sample of the analyzed substance before and after drying, followed by calculating the values of the mass fraction of moisture. Air-thermal measuring installations ASESH-8 are registered in the State Register of Measuring Instruments under No. 58526-14, have a certificate of approval of the type of measuring instruments OC.C.31.005 And No. 56847.The installations undergo initial verification and have the appropriate certificate. General characteristics: - The presence of two independent drying chambers. - Possibility of simultaneous determination of humidity of 12 samples: Each drying chamber of the installation consists of 6 independent cells. You can put 2 buckets in each cell. Total capacity of the ASES Installation-8-2 – 24 bucs. - Convenient access to the cells of the drying chamber: On the front side of the cabinet there are four doors for access to the cells. - Natural ventilation: The absence of rotating elements ensures absolute noiselessness of operation and a long service life. - Built-in timer: The ASESH-8-2 installation has 4 timers, by means of which the end of the drying process is monitored in each section with the output of an audible signal and a light indication. - The output to the operating mode is 30 minutes: The power of air-thermal installations is 1200 watts. When entering the operating mode, the power consumption is the same as that of similar cabinets with low power. SCOPE OF DELIVERY : 1. Installation of ASESH-8-2 2. AO-3 cooler 3. Auxiliary accessories 4. Air-heat control unit: 5. Interface unit for connecting a personal computer with a scale (available on request); 6. software for processing and archiving measurements of humidity determination data; The program allows you to: Set the operating temperature in the chambers via a personal computer Set the necessary parameters of the sample drying process according to the selected method Display all current processes (predrying, drying, cooling) and parameters (temperature, time) during the tests. To monitor the process by means of an electronic timer with the output of an audible signal. Record all weighing results. Perform humidity calculations in accordance with standardized methods. To calculate the humidity with pre-drying, the program uses formulas that allow you to get an accurate result. Archive and print test results. According to the test results of FSUE "UNIIM", it is recommended to use a laboratory mill of the BLIZZARD series for sample preparation. SCOPE OF APPLICATION: 1. Crop production, agriculture and forestry. 2. Products of meat, dairy, fish, flour-milling, feed and microbiological industries. 3. Food industry products. 4. Cellulose, paper, cardboard and products made from them. 5. Medicines, chemical and pharmaceutical products and medical products. 6. Building materials. 7. Products of the logging and sawmilling and woodworking industry. 8. Ground, soils, mineral fertilizers. Technical specifications: The measurement range of the mass fraction of moisture, % from 0.5 to 80 Operating temperature range, °C from 45 to 160 The error of setting and maintaining the temperature in the working area, ° C, not more than 2.0 Limits of permissible absolute error, % ± 0.5 Power consumption, V• A, not more than 1200 Overall dimensions, mm 240 × 260 × 640 Overall dimensions of the cell, mm 75 x 40 x 165 (depth) Weight, kg 28.4

The open system allows you to work with reagents and laboratory plastics from various manufacturers Russian-language software Modifications: - COLIBRI 24 - the ability to select from 1 to 24 samples - COLIBRI 48 - the ability to select from 1 to 48 samples - COLIBRI 96 - the ability to select from 1 to 96 samples Range of working volumes: - COLIBRI 24 - 200 – 5000 mkl - COLIBRI 48 - 30 – 1000 mkl - COLIBRI 96 - 20 – 1000 mkl A unique format of consumable plastic - 8-hole strips and combs Two built-in thermostats The accuracy of temperature maintenance is ± 1 °C Heating/cooling - up to 100 °C / up to 35 °C Universal Thermostat Tube Unit Built-in computer Ready-made allocation protocols The time of one extraction cycle is from 11 minutes Built-in bactericidal UV lamp for interior treatment

Technical specifications: Measurement time, 80 seconds Standard sample volume in a cuvette, 50 ml Spectral range, cm-1 from 8700 to 13200 Spectral resolution, cm-1, no more than 10 The limit of the permissible value of the absolute error of the wave number scale, cm-1 ±0,5 Analyzer warm-up time, min, no more than 30 Continuous operation time of the analyzer, h, at least 8 Overall dimensions, mm, no more than 530x450x380 Weight, kg, not more than 32 Power supply of analyzers from the AC network: AC power supply voltage, V frequency, Hz (220 ±22) (50 ±1) Power consumption, V× A, not more than 110 Average time to failure, h, not less than 2500

Analyzes a wide range of quality indicators (protein/protein, moisture, quantity and quality of gluten (IDC), fat/oil content, water absorption capacity, etc.) It is possible to calculate the amino acid composition of feed components Works with samples of the analyzed substance in the form of grinding The ECANET digital platform allows you to integrate the INFRASCAN analyzers into local networks. Up to 1 million measurement results are stored in the device's memory. Equipped with a universal cuvette, which allows to analyse not only bulk, but also pasty products (mayonnaise). The built-in whiteness module permits to determine the whiteness of the product simultaneously with other quality indicators (moisture, protein, amount of gluten). The analysis time takes 1-1.2 minutes. The device allows to get a result for several indicators in one measurement. High vibration resistance allows to work both in the laboratory and in industrial space. The error of the measurement results meets the requirements of GOST. At each launch of the device, self-testing of internal connections, a monochromator and a detector is provided, which ensures the accuracy of the results throughout the entire operation of the analyzer.

Technical specifications: Measurement time, sec. 80 Standard sample volume in a cuvette, 500 ml Spectral range, cm-1 from 8700 to 13200 Spectral resolution, cm-1, not more than 10 The limit of the permissible value of the absolute error of the wavenumber scale, cm-1 ± 0.5 The level of positive and negative pseudo-scattered light caused by the nonlinearity of the photodetector system (relative to the maximum signal), %, not more than ± 0.25 Analyzer warm-up time, min, no more than 30 Continuous operation time of the analyzer, h, not less than 8 Overall dimensions, mm, not more than 530x485x495 Weight, kg, not more than 32 Power supply of analyzers from the AC network: AC power supply voltage, V frequency, Hz (220 ±22) (50 ±1) Power consumption, V× A, not more than 110 Average time to failure, h, not less than 2500

LAMPIX 8 uses the method of Loop-Mediated Isothermal Amplification of DNA and RNA (LAMP and RT-LAMP) for genetic analysis of any kind.
Key features.

• Compact: supports 8 standard 200μL tubes in a single test run.
• Portable:provides genetic testing in an on-site or mobile laboratory.
• Fast: Result within 15 minutes after the start of the analysis.
• Real-time: Detection of the results with our built-in software.
• Open system: can work with any test kits with FAM / SYBR dyes for isothermal amplification.
• Flexible: possibility to adjust settings for your research purposes.

LAMP TEST KITS: LAMP LYME KIT (Detection of the B.burgdorferi in ixodid ticks) *sensitivity from 50 copies of DNA. SARS-CoV-2 test (COVID-19).
Technical Specifications.

• Excitation source 8 LEDs,
• Excitation detection 8 photodiodes,
• Number of Fluorophores 1 FAM/SYBR/EvaGreen,
• Excitation wavelength 470 nm,
• Detection range 510-530 nm,
• Sample capacity 8 х 200 μl tubes,
• Tube type separate tubes / strips with flat lid,
• Operating temperature range 37˚C to 75˚C with 0.5˚C resolution,
• Lid type heated lid,
• Heated lid temperature range 37.0 ˚C to 75.0 ˚C with 0.5˚C resolution,
• PC connection USB type С port,
• Dimensions W × D × H 115 х 80 х 65 mm,
• Weight 250 g,
• Power 12 V / 18 W external power supply / power bank,
• Software Operating system Win 7-10.

The principle of operation of the electronic diaphanoscope YANTAR is to assess the vitreousness of the image obtained using a digital camera. The vitreous value is calculated using a software-implemented algorithm using special calibration equations. The analysis time is 1 minute. Automation of the vitreous assessment avoids the error associated with the subjective opinion of a specialist. The use of specially developed calibration standards based on optical filters for uniform adjustment of diaphanoscopes permits to coordinate the operation of two or more devices remotely. The interlaboratory error in determining the vitreousness on the devices included in the network does not exceed the standard. All the results of the determination of the vitreousness of wheat with the corresponding grain images are stored in the archive. If necessary, specialists can print the protocols of the current or any of the previous definitions. THE ALGORITHM OF OPERATION: 1. Pour the grains into the cassette and close the lid made of transparent glass. 2. Install the cassette in the diaphanoscope. 3. Launch the program. 4. Choose a product 5. Software processing of the digital image of grains in accordance with the selected product 6. Calculation of computer results. In 2023, a new national standard GOST R "Wheat. Determination of vitreousness by optical-computer method".

The Kjeldahl method is one of the most accurate methods for determining nitrogen and protein in a wide group of products, but, unfortunately, it has a number of significant drawbacks - these are low speed, a large number of possible losses during the analysis, bulky equipment, and the use of aggressive reagents. Sibagropribor Holding presents KELTRUN (KELTRUN) - a set of equipment for carrying out a complete analytical cycle according to the Kjeldahl method, which will allow: • to increase the speed of analyzes (high speed of distillation and ashing, simultaneous processing of several samples); • ensure the safety of personnel (high quality of reaction vessels, effective absorption of acid vapors by the exhaust system, additional protection of personnel in emergency situations); • reduce possible losses in the analysis process; • improve the reproducibility of results. «KELTRAN» (KELTRUN) will allow you to determine nitrogen / protein in the widest list of substances: • food products: dairy, cereals, meat, cereals, etc.; • feed and compound feed; • fertilizers; • water, drinks, beer; • soil, bottom sediments, sediment samples, activated sludge; • crude oil, lubricants; • various chemicals; • alcohol content in wines, musts and spirits; • etc. The set of equipment «KELTRAN» (KELTRUN) allows you to analyze according to GOST and determine the nitrogen content in the range of 0.02 - 99.00%. Composition of the complex «KELTRAN» (KELTRUN): - Digestor; - Distiller; - Scrubber (*not included in the price of the complex); - Titration unit: manual, semi-automatic or automatic (*not included in the price of the complex); Warranty - 1 year. Important feature! In many distillers (made in China and others), when used, alkali passes through a valve-type pump, with a low production resource (sometimes the resource is enough for only 3 months). In the distiller of our production, the alkali passes through a RELIABLE PERISTALTIC PUMP, this ensures a long service life of the distiller! Package options Cost (including VAT): Digestor, Distiller, Water jet pump 379,400 rubles; Digestor, Distiller, Water jet pump, Scrubber 434,700 rubles; Digestor, Distiller, Water jet pump, Manual titration unit 396,900 rubles; Digestor, Distiller, Water jet pump, Scrubber, Manual titration unit 452,200 rubles; Digestor, Distiller, Water jet pump, Kit «Titrion-pH» (c2) 605,400 rubles; Digestor, Distiller, Water jet pump, Scrubber, «Titrion-pH» kit (c2) 660,700 rubles.

The principle of operation of the mills is based on the grinding of the product, rotating at high speed with a knife in combination with a cyclic rotation of the grinding unit. In order to achieve uniform grinding and homogenization of the sample, the grinding unit must be tilted during grinding. The angle of inclination is set automatically according to the selected mode. FEATURES: 1. Programmable grinding modes The laboratory mill has two grinding modes: "Sunflower" - used for grinding oilseeds. "Grain. Feed" is used for grinding grain, leguminous crops, feed and raw materials for their production. Depending on the crushed product, the operator selects the desired mode of the grinding process. The installation of the grinding mode options is carried out using a specially developed program via a PC. It is possible to install an additional grinding mode using a PC. 2.Easy operation with information display. 3. Crushing of samples with a high fat content (up to 55%). 4. Sample preparation without heating. The special design of the grinding chamber (grinding is carried out in the upper bowl made of aluminum) and the use of special knives ensure rapid grinding and minimize heating of the sample, which eliminates moisture loss. According to the test results of FSUE "UNIIM", mills are recommended for sample preparation during the analysis to determine humidity. They are part of the installation of the measuring air-thermal ASESH-8 (RU. p.31.005.A No. 56847). 5. COOLING SYSTEM without forced water cooling. For continuous comfortable operation with the cooling system, the mill is equipped with two grinding cups. 6. Grinding of various types of samples. The presence of knives of various geometries and the possibility of their quick replacement when changing the crushed product, allows the mill to be used for grinding a wide range of agricultural products – from wheat grains to soybeans and sunflower seeds, according to specially developed algorithms. Knives are included in the delivery package of the mill: knife No. 2 – for grinding oilseeds and cereals; knife No. 4 – for grinding feed and raw materials for their production; knife No. 1 – designed for chopping soybeans.

QuattroPlex is the first Russian open multiplex platform for the quantitative and qualitative analysis of biomarkers by immunofluorescence analysis on magnetic beads. The detection technology copies the xMap technology, which allows analysis of several dozen analytes in a minimum volume. QuattroPlex benefits:

• • Multiplexing - diagnostics of up to 50 markers in one sample in one analysis
• • analysis of a wide range of markers (rheumatology, autoimmune diseases, HLA, cytokines, infections)
• • open system - use of any test systems based on magnetic coded microspheres
• • high sensitivity - possibility of qualitative and quantitative analysis
• • design that requires minimal desktop space
• • possibility of use in mobile laboratories.

Specifications:

• • Registered size of microspheres, microns — from 0.5 to 100;
• • 3 fluorescence registration channels;
• • fluorescence excitation wavelengths, nm — from 380 to 850;
• • wavelengths of fluorescence registration, nm — from 450 to 950;
• • detector - CMOS matrix;
• • sample volume, µl — from 30 to 60;
• • number of test samples per load — 1 (in a chip);
• • time for analysis of one sample, sec — 4;
• • Results management and analysis software - QuattroPlex results management and analysis software, compatible with Win/Linux;
• • interfaces for connecting to a laptop/PC — Internet/Wi-Fi;
• • dimensions W×D×H, cm — 20×20×30.

Delivery set:

• • system of multiplex analysis of biomarkers QuattroPlex;
• • starter set of consumables;
• • computer, keyboard, mouse and monitor.

The principle of operation of the mill is based on grinding the product with a steel knife rotating at high speed in combination with cyclic rotation of the grinding unit. FEATURES: 1.Fast and high-quality grinding of solid products The high power of the electric motor in combination with a specially designed knife of a special shape and automatic cyclic rotation of the grinding unit of the mill at 210 and 90 makes it possible to qualitatively grind samples of solid products in a short time. It is possible to grind lump cake up to 20 mm in size. 2. Sample preparation without heating. Improved heat dissipation due to the design of the grinding cup, the outer surface of which has the appearance of a radiator, high grinding speed and the possibility of cooling the grinding bowl prevent possible overheating of the sample, which eliminates moisture loss and allows the mill to be used for sample preparation during analysis to determine the moisture content of products. They are part of the installation of the measuring air-thermal ASESH-8 (RU.C.31.005.A No. 56847). According to the test results of FSUE "UNIIM", the mills are recommended for sample preparation during the analysis to determine humidity. 3. COOLING SYSTEM without forced water cooling. For continuous comfortable operation with the cooling system, the mill is equipped with two grinding cups. 4. Quick and easy cleaning of the mill. A mode for grinding solid products with an improved cleaning system of the grinding chamber has been implemented. 5.Grinding headset with long service life The grinding set of the mill is specially designed to work in extreme conditions – high productivity and high mechanical load. Special inserts made of knife-hardened stainless high-strength steel with the effect of forging the grinding chamber and cup ensure long-term operation of the mill when grinding solid and granular products. The knife made of high-strength stainless knife steel guarantees their high wear resistance.