SMR-9 Geodesic satellite multi-frequency instruments

Основные характеристики Диапазон измерения температуры, °С От -70 до + 200 Погрешность измерения температуры, °С, не более 1 Номинальное сопротивление при 25 С,кОм 1.0 Длина рабочей части PT 1000 (погружной) 250 мм Длина ручки 50 мм, диаметр ручки М12 Длина провода до 600 мм

The result of determining the energy distribution of the neutron radiation flux density is used to calculate such quantities as: - integral neutron flux density; - the average energy of neutron radiation in the spectrum; - the average neutron radiation energy by dose; - dose equivalent per unit flow density; - dose equivalent; - effective dose. ▪ Methodological support of measurements ▪ It is possible to supply an expanded set of polyethylene retarder spheres with diameters: 3,5”; 4,5”; 5”; 7”; 9”; 9,5”

The meter-recorder IS-203.2 is a microprocessor-based meter designed to measure temperature. Equipped with a non-volatile storage device and a real-time clock. The device has two measuring channels. The measurement results are stored in the non-volatile memory with a volume of 15,000 measurements per channel. The operating conditions of the meter IS-203.2.0 Ambient temperature, ° C: -20...+50. Relative humidity, %: up to 90. Atmospheric pressure, kPa: 70...106.7. Scope of application of the meter IS-203.2.0 Control of technological processes in various industries, including: utilities, construction, food and pharmaceutical industries, agriculture, etc. Warehouses (grocery, industrial, pharmaceutical, etc.). Transportation (grocery, industrial, pharmaceutical, etc.). Functionality of the meter IS- 203.2.0 Temperature measurement by external sensors. Saving the measurement results in the device memory. Indication of the results of current measurements, time, channels included, interval between measurements, free memory of the device, battery capacity, serial number of the device, time of the next measurement. Operational start and stop of the measurement process. Data transfer to a PC via a COM port or USB.

The IS-203.3 meter-recorder is designed to measure and convert analog signals from primary converters (temperature, pressure, humidity, etc.) into the value of the measured physical quantity, as well as to register measuring information in the device's memory and then transfer it to a computer (RS 485 or USB) for visualization in the form of tables and graphs. The meter recorder is a microprocessor-based meter equipped with a non-volatile storage device and a real-time clock. The device has the ability to work as a network device (up to 20 network devices at the same time) or stand-alone with subsequent connection to computers (laptop) for reading data. The operating conditions of the meter IS-203.3 Ambient temperature, °C: -30...+50. Relative humidity, %: up to 90. Atmospheric pressure, kPa: 70...106.7.

Designed for: measurements of the relative permittivity and the tangent of the dielectric loss angle of materials at a frequency of 9 GHz in accordance with GOST R 8.623-2015 "GSI.

▪ Rapid adaptation to changes in the radiation background ▪ Audible and light alarms when gamma radiation is detected ▪ Mobility and the possibility of forming passages ▪ Self-control of components in the process of work ▪ The possibility of continuous or episodic radiation monitoring ▪ The possibility to work from a 230V, 50Hz network or from a built-in rechargeable battery Compliance with the international standard IEC 62244:2006 Stationary radiation monitors for the detection of radioactive and special nuclear materials at state borders

Logging data on dose rate levels and exceeding threshold levels Software that allows you to display on a PC monitor the current radiation situation at a controlled facility Backup power supply High radiation resistance – at least 50,000 Sv for UDKG-37 Failure diagnostics The possibility of using the system for dosimetric monitoring of both pulsed and continuous gamma radiation The possibility of using the DKS-AT1123 dosimeter autonomously as a wearable device

The NTM-Terminal block is a multifunctional device that allows you to choose: the necessary antenna-converter, operating mode, measurement procedure in relation to the object of examination, recording of measurement results.

It is designed to control the excess pressure during the crimping of pipelines before putting them into operation, as well as during scheduled system health checks. The devices are registered in the State Register of Measuring Instruments for No. 30414-11, No. 43646-10 and are approved for use in the Russian Federation. Features of the CHU-N kit Carrying out pressure testing before the start of commissioning allows you to identify possible defects in seams and pipes, ensuring their tightness and reliability of insulation. The kit is designed to work in the field in order to record and archive the measured results to identify possible defects. The CHU-M kit is a portable complex with autonomous power supply.

PARMA TENSOR-2 (AC bridge) is designed for automatic measurements of: · capacitance and tangent of the dielectric loss angle of high-voltage insulation of capacitors, inputs, transformers using an external high-voltage capacitor, both in laboratory and in the "field" conditions · effective values of the first harmonic of the current and voltage of the industrial frequency · the angle of phase shift between the signals supplied to the inputs of the device · network frequencies * Measurements can be carried out according to the "straight" and "inverse" (inverted) scheme. * Allocates the vector of the influence current, which makes it possible to dispense with the phase regulator of the test voltage source or devices for compensating the influence current.

Rapid adaptation to changes in the radiation background Audible and light alarms The possibility to create a network of MCI (up to 32) under the control of a PC and specialized software Mobility and the possibility to organize the control of passages in a short time High reliability and self-control Backup power supply