Fume Umbrella-Cupboard SHZV-NRZH.100

The SHVM NVK 1200 MON+ is a metal fume cupboard with plumbing for work in the laboratory. The table top is made of monolithic ceramics, its width is 1200 mm. External dimensions of the cabinet (W×D×H): 1260×750×2250 mm. Internal dimensions of the camera (W×D×H): 1200×600×1168 mm. Table top material: monolithic ceramic. A reliable and durable fume cupboard for the laboratory The table top is made of a single ceramic plate with a width of 1200 mm. The seamless monolith of the countertop provides the highest reliability and durability. The ceramics are great for all chemical laboratories, including those that work with substances at high temperatures. It perfectly tolerates heat, is moisture-resistant, resistant to acids and alkalis. High-temperature equipment (drying cabinets, muffle furnaces) can be placed on the table top. The cabinet is mounted on an all-welded metal frame covered with durable powder paint. All panels are made of polymer-coated metal. The front anti-spill side is made of AISI-316 polished stainless steel. There are four exhaust zones in the working chamber: they are located in the hood of the exhaust box and above the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. The hood area is also made of metal. The protective screen of the cabinet can be easily lifted with one hand. It folds up and when lifted does not increase the overall height of the cabinet. It is made of 4 mm tempered glass in an aluminum frame. The small sink-drain is made of polypropylene, resistant to aggressive chemicals. Its internal dimensions: 218×115×122 mm. The faucet is made of brass and covered with polypropylene. The sockets and the switch of the LED lamp are located outside the working area, on the right-hand side of the front panel of the cabinet. The sockets are splash-proof and designed for current up to 16 A and voltage up to 250 V. Next to the switch there is a toggle switch of the automatic emergency power off. The reagents needed for work can be placed in the lower cabinet. The cabinet is also made of metal. It has three swing doors and one fixed shelf. It has its own hood (pipe diameter 100 mm), which can be connected to the general exhaust system of the cabinet using the nozzle included in the cabinet kit. The cabinet legs are adjustable in height, allowing you to place the cabinet even on a rather uneven floor. Advantages of the cabinet SHVM NVK 1200 MON+ A metal fume cupboard with plumbing, an excellent choice for any laboratory; Durable, reliable and very convenient to use; The protective screen is made of tempered glass; The hood is built into the cabinet, reagents can be safely stored in it. Application of the SHVM NVK 1200 MON+ cabinet Exhaust laboratory cabinets are used when working with toxic and harmful volatile materials, with clean materials, with dissolution or decomposition under heat treatment, when conducting sample analysis. Fume cupboards of the NV-Comfort series are used in laboratories of the widest profile: at food and light industry enterprises, in higher educational and scientific institutions, in chemistry classrooms at school, in quality control centers, medical organizations.

The SHVM NVK 1200 MON is a metal fume cupboard for laboratory. The table top is made of monolithic ceramics, its width is 1200 mm. External dimensions of the cabinet (W×D×H): 1260×750×2250 mm. Internal dimensions of the camera (W×D×H): 1200×600×1168 mm. Table top material: monolithic ceramic. Reliable and durable construction The table top is made of a single ceramic plate with a width of 1200 mm. The seamless monolith of the countertop provides the highest reliability and durability. THe ceramics are great for all chemical laboratories, including those that work with substances at high temperatures. It perfectly tolerates heat, is moisture-resistant, resistant to acids and alkalis. High-temperature equipment (drying cabinets, muffle furnaces) can be placed on the table top. The cabinet has an all-welded metal frame covered with durable powder paint. All panels are made of polymer-coated metal. The front anti-spill side is made of polished stainless steel AISI-316. There are four exhaust zones in the working chamber: they are located in the hood of the exhaust box and just above the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. The hood area is also made of metal. The protective screen of the cabinet can be easily lifted with one hand. It folds up and when lifted does not increase the overall height of the cabinet. It is made of 4 mm tempered glass in an aluminum frame. The sockets and the switch of the LED lamp are located outside the working area, on the right-hand side of the front panel of the cabinet. The sockets are splash-proof and are designed for current up to 16 A and voltage up to 250 V. Next to the switch there is a toggle switch of the automatic emergency power off. The reagents needed for work can be placed in the lower cabinet also made of metal. The cabinet has three swing doors and one fixed shelf. It has its own hood (pipe diameter 100 mm), which can be connected to the general exhaust system of the cabinet using the nozzle included in the cabinet kit. The cabinet legs are adjustable in height, allowing you to place the cabinet even on a rather uneven floor. Advantages of the SHVM NVK 1200 MON cabinet A metal fume cupboard suitable for any laboratory; Durable, reliable and very convenient to use; The protective screen is made of tempered glass; A hood is built into the cabinet, reagents can be safely stored in it. Application of the SHVM NVK 1200 MON cabinet Exhaust laboratory cabinets are used when working with toxic and harmful volatile materials, with clean materials, with dissolution or decomposition under heat treatment, when conducting sample analysis. Fume cupboards of the NV-Comfort series are used in laboratories of the widest profile: at food and light industry enterprises, in higher educational and scientific institutions, in chemistry classrooms at school, in quality control centers, medical organizations.

A 1500 mm wide umbrella cupboard with a stainless steel exhaust chamber and a countertop made of porcelain stoneware, monolithic ceramics or stainless steel. Overall dimensions 1500x800x1905 mm Internal dimensions 1450x775x950 mm The diameter of the exhaust pipe is 200 mm Weight 135 kg

The NV-1500 SHV-M is one of the budget fume cupboards of the NV line. It is single-frame, with a laminated table top 700 mm deep. It is intended mainly for analytical laboratories. External dimensions of the cabinet (W×D×H): 1410×700×1960 mm. Dimensions of the working area (W×D×H): 1378×540×750 mm. Table top: laminated chipboard. A minimalistic solution for your laboratory The NV-1500 SHV-M fume hood has a minimum of functions, which makes it so inexpensive. The table top is made of laminated chipboard. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. The working area is closed by one lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1378×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the height of the cabinet will be 2470 mm. The working area is illuminated by an LED lamp (included in the package). The switch is located on the right-hand side of the cupboard. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

The SHVM NVK 1500 MON is a metal fume cupboard for laboratory. The table top is made of monolithic piece of ceramics. External dimensions of the cabinet (W×D×H): 1560×750×2250 mm. Internal dimensions of the camera (W×D×H): 1500×600×1168 mm. Table top material: monolithic ceramic. A reliable and durable laboratory cabinet The table top is made of monolithic ceramics. It is perfect for all chemical laboratories, including those that work with substances at high temperatures. It perfectly tolerates heat, is moisture-resistant, resistant to acids and alkalis. High-temperature equipment (drying cabinets, muffle furnaces) can be placed on the countertop. The width of the ceramic plate is 1200 mm, that is, there will be one seam in the countertop. The cabinet is mounted on an all-welded metal frame covered with durable powder paint. All panels are made of polymer-coated metal. The front anti-spill side is made of the AISI-316 polished stainless steel. There are four exhaust zones in the working chamber: they are located in the hood of the exhaust box and above the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. The hood area is also made of metal. The protective screen of the cabinet can be easily lifted with one hand. It folds up and when lifted does not increase the overall height of the cabinet. It is made of 4-mm tempered glass in an aluminum frame. The sockets and the switch of the LED lamp are located outside the working area, on the right-hand side of the front panel of the cabinet. The sockets are splash-proof and are designed for current up to 16 A and voltage up to 250 V. Next to the switch there is a toggle switch of the automatic emergency power off. The reagents needed for work can be placed in the lower cabinet cabinet. The cabinet is also made of metal. The cabinet has swing doors and one non-removable shelf. It has its own hood (pipe diameter 100 mm), which can be connected to the general exhaust system of the cabinet using the nozzle included in the cabinet kit. The cabinet legs are adjustable in height, allowing you to place the cabinet even on a rather uneven floor. Advantages of the SHVM NVK 1500 MON cabinet A metal fume cupboard, perfect for any laboratory; The wide table top allows you to equip the workplace as conveniently as possible; It is durable, reliable and very convenient to use; The protective screen is made of tempered glass; The cupboard is built into the cabinet, reagents can be safely stored in it. Application of the SHVM NVK 1500 MON cabinet Exhaust laboratory cabinets are used when working with toxic and harmful volatile materials, with clean materials, with dissolution or decomposition under heat treatment, when conducting sample analysis. Fume cupboards of the NV-Comfort series are used in laboratories of the widest profile: at food and light industry enterprises, in higher educational and scientific institutions, in chemistry classrooms at school, in quality control centers, medical organizations.

The Korsa NV-1500 SHV-NERZH Laboratory fume cupboards are single—frame cabinets with a width of 1410 mm with a stainless steel countertop. External dimensions of the cabinet (W×D×H): 1410×700×1960 mm. Dimensions of the working area (W×D×H): 1378×540×750 mm. Table top: stainless steel. Convenient fume cupboards for comfortable work in the laboratory Working surface material: stainless steel. It is well suited for biological or medical laboratories, but it is not recommended for use in chemical laboratories. It is resistant to prolonged exposure to temperature, organic solvents, and oils. It has limited resistance to short-term exposure to concentrated mineral acids and alkalis and is destroyed by prolonged exposure to concentrated acids. The working area is closed by a single lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1378×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, with the glass raised, the total height of the cabinet will be 2470 mm. The working area is illuminated by an LED lamp (included in the package). The switch is located on the right-hand side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets have the IP20 degree of protection, maximum load: 1.5 kW. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard with a thickness of 16 mm) are edged with a durable PVC edge with a thickness of 2 mm, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

The Kors NV-1200 SHV-U laboratory fume hood is a single—frame cabinet with a ceramic granite countertop 1100 mm wide and a small built-in polypropylene sink. External dimensions of the cabinet (W×D×H): 1100×700×1960 mm. Dimensions of the working area (W×D×H): 1068×540×750 mm. Table top: granite tiles. Reliable fume cupboard for laboratories The cabinet is available in two versions: with a hood from the lower cabinet and without it. In a cabinet with a hood, various aggressive reagents can be stored, in a cabinet without a hood, it is better to store only laboratory glass or instruments. Working surface material: porcelain tile. It is moisture-resistant and perfectly withstands high temperatures. It is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Limited resistance to hydrofluoric acid. This is one of the most popular types of countertops for laboratory furniture. The small sink-drain is made of polypropylene, resistant to aggressive chemicals. Its diameter is 135 mm and its depth is 110 mm. The base of the cabinet is made on an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a fairly uneven floor. Working area of the fume cupboard The working area is closed by one lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1068×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it is small enough in length, otherwise you will not be able to close the cabinet. The working area is illuminated by a fluorescent lamp (included in the package). The switch is located on the right side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets have the IP20 degree of protection, maximum load: 1.5 kW. What are the other options? If you need to place large equipment, you may be interested in the cabinets for muffle furnaces. Also in the line there are large cabinets with plumbing fixtures: NV-1500 NV-U and two-frame NV-1500 SHV-U and NV-1800 SHV-U.

The Kors NV-1500 SHVD-U laboratory fume cupboard is a two—frame cabinet with a granite countertop with a width of 1410 mm and a small built-in sink made of polypropylene. External dimensions of the cabinet (W×D×H): 1410×700×1960 mm. Dimensions of the working area (W×D×H): 1378×540×750 mm. Table top: granite tiles. Working surface material: porcelain tile. It is moisture-resistant and perfectly withstands high temperatures. It is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Limited resistance to hydrofluoric acid. This is one of the most popular types of countertops for laboratory furniture. The small sink-drain is made of polypropylene, resistant to aggressive chemicals. Its diameter is 135 mm and its depth is 110 mm. The working area is closed by two lifting frames with a counterweight. As standard, there are two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1378×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the height of the cabinet will be 2470 mm. The NV-1500 SHVD-U fume cupboard is equipped with an LED lamp with a switch and two sockets, one of them with grounding. Sockets have the IP20 degree of protection, the maximum load on them: 1.5 kW. The working chamber is an all-welded metal frame in powder coating. Load-bearing laminated panels (chipboard with a thickness of 16 mm) are edged on the facade with a durable PVC edge with a thickness of 2 mm, which increases the impact resistance and mechanical strength of the products. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

BASIC EQUIPMENT: Working box front guide posts – aluminum profile painted with powder paint (RAL 7035/RAL 5023), in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) the front anti-spill side is acid-resistant polished stainless steel. AISI 316 steel rear, upper, side panels – metal painted with powder paint (RAL 7035) with the texture of shagreen leather inner capsule made of polypropylene lined with ceramic plates of the rear and side panels to a height of 380mm 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-780mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – polypropylene on the top panel: LED dust– and moisture-proof lamp 2x22 W (IP65) is separated from the workspace by tempered glass with a thickness of 4mm flange d=250mm (distance from the back panel to the center of the flange - 170mm) switching box with automatic emergency power off 16A 3 exhaust levels easily removable exhaust visors counterweights are placed in the front pylon racks and are easily serviced Frame base collapsible frame made of rectangular metal profile painted with powder paint (RAL 7035) with the texture of shagreen leather service panel - aluminum profile painted with powder paint (RAL 5023) with the texture of shagreen leather adjustable supports

Kors NV-1200 SHV-B laboratory fume hoods are single—frame cabinets with a width of 1100 mm with a countertop made of granite tiles. External dimensions of the cabinet (W×D×H): 1100×700×1960 mm. Dimensions of the working area (W×D×H): 1068×540×750 mm. Table top: granite tiles. Convenient fume cupboards for comfortable work in the laboratory The cabinet is available in two versions: with a hood from the lower cabinet and without it. In a cabinet with a hood, various aggressive reagents can be stored, in a cabinet without a hood, it is better to store only laboratory glass or instruments. Working surface material: porcelain tile. It is moisture-resistant, perfectly withstands high temperatures. It is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. It has limited resistance to hydrofluoric acid. This is one of the most popular choices for work surfaces, suitable for most laboratories. Drying cabinets or other highly heated appliances can be placed on such a countertop. The working area is closed by a single lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1068×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, with the glass raised, the total height of the cabinet will be 2470 mm. The working area is illuminated by a fluorescent lamp (included in the package). The switch is located on the right side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets with IP20 degree of protection, maximum load: 1.5 kW. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard with a thickness of 16 mm) are edged with a durable PVC edge with a thickness of 2 mm, which increases their impact resistance and mechanical strength. The legs of the cabinet are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

NV-1500 SHVD-M is one of the budget fume cupboards of the NV line. It is two-frame, with a laminated table top 700 mm deep. It is intended mainly for analytical laboratories. External dimensions of the cabinet (W×D×H): 1410×700×1960 mm. Dimensions of the working area (W×D×H): 1378×540×750 mm. Table top: laminated chipboard. A minimalistic solution for your laboratory The NV-1500 SHVD-M fume cupboard has a minimum of functions, but due to this it is inexpensive. The table top is made of laminated chipboard. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. The working area is closed by two independent lifting frames with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1378×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the height of the cabinet will be 2470 mm. The working area is illuminated by an LED lamp (included in the package). The switch is located on the right-hand side of the cabinet body. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a fairly uneven floor.

Kors NV-1200 SHV-PB Laboratory fume cupboard is a single—frame cabinet with a width of 1100 mm with a table top made of polypropylene. External dimensions of the cabinet (W×D×H): 1100×700×1960 mm. Dimensions of the working area (W×D×H): 1068×540×750 mm. Table top: polypropylene. Convenient fume cupboards for comfortable work in the laboratory Working surface material: monolithic polypropylene. It is moisture-resistant, resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Poorly resistant to high temperatures. Polypropylene countertops are suitable for chemical laboratories that work a lot with concentrated inorganic acids and alkalis. The working area is closed by a single lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1068×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the total height of the cabinet will be 2470 mm. The working area is illuminated by a fluorescent lamp (included in the package). The switch is located on the right side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets have the IP20 degree of protection, maximum load: 1.5 kW. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard with a thickness of 16 mm) are edged with a durable PVC edge with a thickness of 2 mm, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor. What are the other options? There are larger cabinets with polypropylene countertops: NV-1500 SHV-PB, NV-1500 SHVD-PB and NV-1800 SHVD-PB.

The Kors NV-1100 SHV-LVZH laboratory fume cupboard is a specialized single—frame cabinet with a granite countertop with a width of 1090 mm and a built-in iron compartment for storing highly inflammable liquids (HIL). External dimensions of the cabinet (W×D×H): 1090×700×1960 mm. Reliable fume cupboard for storage of HIL and combustible substances The lower compartment of the cabinet is a built—in metal cabinet designed for the safe storage of highly inflammable liquids. The double walls of the cabinet with an insulating air space provide fire resistance. Compartment capacity: 57 liters. External dimensions: 1090×460×460 mm. It is made of welded steel with a thickness of 1 mm. The width of the insulating air layer is 38 mm. It is coated with a durable epoxy polyester powder paint that protects against moisture and corrosion (nevertheless, acids and alkalis cannot be stored in it). The lower shelf with sides 50 mm high protects the laboratory from accidental spillage of liquids. The middle shelf can be hung at different heights in 76 mm increments. There are two ventilation openings with flame arresters in the sides of the cabinet. The compartment doors open at 180 degrees. They are equipped with a lock that can be sealed. Working area of the fume cupboard Working surface material: porcelain tile. It is moisture-resistant and perfectly withstands high temperatures. It is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Limited resistance to hydrofluoric acid. This is one of the most popular types of countertops for laboratory furniture. The working area is closed by a single lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the height of the cabinet will be 2470 mm. The working area is illuminated by a fluorescent lamp (included in the package). The switch is located on the right side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets have the IP20 degree of protection, maximum load: 1.5 kW. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor. Advantages of the Korsa NV-1100 SHV-LVZH cabinet A specialized solution for laboratories that work a lot with highly inflammable and combustible substances. It is suitable for small-sized rooms. Heating plates or baths can be placed on the porcelain stoneware surface. It is resistant to high temperatures. It is convenient to work standing up: the height of the work surface from the floor is 85 cm (this is the height of an ordinary kitchen corner). Application of the Korsa NV-1100 SHV-LVZH cabinet Exhaust laboratory cabinets are used when working with toxic and harmful volatile materials, with clean materials, with dissolution or decomposition under temperature treatment, during sample analysis and many others. In this cabinet, highly inflammable liquids (HIL) and combustible substances can be stored in a special metal compartment. In the event of a fire in the laboratory, this compartment can maintain a safe temperature inside for some time. Fume cupboards of the NV series are used in laboratories of the widest profile: at food and light industry enterprises, in higher educational and scientific institutions, in chemistry classrooms at school, in quality control centers, medical organizations.

Overall dimensions 1200x800x1905 mm Internal dimensions 1150x775x950 mm The diameter of the exhaust pipe is 200 mm Weight 108 kg

BASIC EQUIPMENT Working box front guide posts – aluminum profile painted with powder paint (RAL 7035/RAL 5023), in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) front anti–spill side - polypropylene working surface - polypropylene 15mm thick removable plate 600*600mm with a ceramic granite work surface for placement heating plates (2 pcs.) 2 dependent lifting screens filled with transparent PVC, 5mm thick in a polypropylene frame in the lower screen – sliding doors made of transparent PVC with a thickness of 5mm lifting 0-780mm, does not change the dimensions of the cabinet when lifting the counterweights are placed in the front pillars-pylons and are easily serviced upper fixed screen – polypropylene inner part the working box is a fully sealed polypropylene capsule with a back wall washing system, a drainage channel and a polypropylene pipe for cold water 3 levels of hoods easily removable polypropylene exhaust canopies polypropylene drain sink on the top panel are placed: LED dust- and moisture-proof lamp (2X22W IP65) separated from the workspace by transparent PVC switching box with automatic emergency power off 16A flange with damper plug for air inflow d=200mm flange with aspiration collector for air outflow d=250mm (distance from the rear panels up to the center of the flange – 155mm) cabinet ventilation system

BASIC EQUIPMENT Working box the front guide posts are aluminum profile painted with powder paint (RAL 7035/RAL 5023), in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) the front anti-spill side is acid-resistant polished stainless steel. AISI 304 steel rear, upper, side panels – metal painted with powder paint (RAL 7035) with the texture of shagreen leather the inner surfaces of the working box are lined with chemically resistant HPL plastic 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-780mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – tempered glass in an aluminum frame on the top panel: LED dust- and moisture-proof lamp (2X10W IP65) is separated from the workspace by tempered glass thickness of 4mm flange d=250mm (distance from the back panel to flange center – 170mm) easily removable exhaust canopies 3 exhaust levels on the left side panel service module with cold water supply pipe and wall-mounted drain sink made of polypropylene cold water supply valve in the left rack of the box counterweights are placed in the front racks-pylons and are easily serviced Frame base collapsible frame made of rectangular metal profile painted with powder paint (RAL 7035) with the texture of shagreen leather service panel - aluminum profile painted with powder paint (RAL 7035/RAL 5023) with the texture of shagreen leather adjustable supports module with two drawers