Shaft furnace LF LF-70/13-G1

High-temperature furnaces are capable of heating materials up to 1700 degrees. The scope of their application covers the heat treatment of various materials in an inert medium or vacuum. TULA-TERM furnaces are used for heat treatment of plastics, ceramics, metals, alloys, lacquers and other materials. The equipment allows sintering, annealing, soldering, quenching, drying, burning and molding. In industry, our installations are most often used for quenching parts and sintering hard alloys.

Vacuum compression furnace SNVS-4,5.5,5/3-I2PD is designed for drying, degassing in vacuum and under pressure at temperatures up to 300 0C.

Designation SSO-6.18/11 Power, kW 40 Diameter, mm 600 Height, mm 1800

Electric tubular laboratory furnaces are designed for calibration of thermocouples and dilatometers, heat treatment and determination of the melting point of metals, alloys and other work at temperatures up to 1100 ° C in stationary laboratories. SUOL tubular furnaces are used in many industries and agriculture, are indispensable in factory and research laboratories.

Vacuum resistance furnaces are necessary for heating products before pressure treatment, for sintering, degassing, quenching, annealing, soldering and chemical-technological processes. Such furnaces among all the variety of thermal equipment are considered the most environmentally friendly – heat treatment is carried out at t up to +2500 ° C in a purified vacuum. Under certain conditions, vacuum furnaces are used to work with neutral gases. The outer part of the furnace is made of stainless steel and is cooled by liquid. The inner part of the working chamber, where the heat treatment of materials is carried out, is made of an alloy of molybdenum and tungsten. The components are characterized by a low inertia force, reduced gas separation. The settings are available on the control panel, where the instruments, automatic and manual control switches are located. At every enterprise of the electronic industry, nuclear power, an explosion-proof vacuum resistance furnace is needed. The same applies to areas where various products undergo heat treatment at the stage of production and preparation for use

Designation SSHOL-10/11 Supply voltage, 220 ± 10% Network frequency, Hz 50 Power consumption, W, max 5000

The control cabinet of thermal equipment SHUP-65-1 is designed to control industrial single-zone furnaces with a maximum power of up to 65 kW and a voltage of 380 volts connected by a star or triangle. The cabinets have an emergency detector and a system for monitoring the operating modes of the equipment. The control cabinet of thermal equipment SHUP-65-1 is equipped with a remote monitoring and control system with an RS-485 or Ethernet interface. The dispatching system developed in Russia does not require significant additional costs for integration into the dispatching systems of thermal workshops.

Designation: SNO-6.12.4 Temperature: 1200 Opendoors: electromechanical Camera size (w.G.V.):600x1200x400 Regulation zones: 1

Designation SSO-10.20/11 Power, kW 90 Diameter, mm 1000 Height, mm 2000

Designation SHUP-15-1 Switching power, kW 15 Automatic switch, A 32 Supply network voltage, V/Hz 380

Designation: SNOT 6.15.6/12.5 Temperature: 1250 Opendoors: electromechanical Hearth drive: electromechanical Camera Size: (WXDXH) 600x1500x600 Regulation zones: 2

B – vacuum, 4 – the amount of the working space in dm3, 18 – the maximum operating temperature divided by 100, i.e., 1800 ° C.

Designation SNO(H)-6/12.5 Power, kW, no more than 8 Supply network voltage, V 380 Frequency, Hz 50

Design features: Programmable microprocessor temperature controller; Three programs of ten steps with the ability to set the temperature, heating speed and holding time for each step; Manual heating mode with timer with sound notification and auto-off; Durable ceramic muffle; Semi-open heaters on four sides of the chamber; Backlit graphic display; Conveniently located control panel; Automatic shutdown of heating when opening the door; Sound and light alarm; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1300 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to the maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than 200x110x190 mm Overall dimensions, WxHxD, not more than mm 505x565x565 Rated supply voltage, 220 V Rated power, W 2800

Laboratory mine crucible melting furnace SSHOL-3/4-T is designed for melting solder of tin and other metals at temperatures up to 400 ° C. The heaters of the SSHOL furnace are located on the outside of the ceramic retort. Oven lid - removable

Design features: Programmable microprocessor temperature controller; Three programs of ten steps with the ability to set the temperature, heating speed and holding time for each step Manual heating mode with timer with sound notification and auto-off; Durable ceramic muffle; Closed heaters on four sides of the chamber; Backlit graphic display; Conveniently located control panel; Automatic shutdown of heating when opening the door; Sound and light alarms; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1100 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to the maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than 200x110x190 mm Overall dimensions, WxHxD, not more than mm 505x565x565 Rated supply voltage, 220 V Rated power, W 2800

Designation SNO-10 Volume, l 10 The material of the working chamber is ceramic Heating 4 sides Power consumption, W, max 4500 Minimum operating temperature, 0C 100