Catalog
Back to search results
Water purification system SOV-M-20
Back to search results
Water purification system SOV-M-20
Installation for obtaining analytical quality water UPVA-5
from
115 000 ₽
Capacity, l/h
5.0 (-10%)
Purpose
preparation of distilled water of type 2 according to GOST 52501-2005 "Water for laboratory analysis" FS.2.2.0019.18 "Water for injection"
Heating elements
Heating element 3.5 kW 220V (stainless steel) – 1 pc.
The quality of the produced water
GOST 52501-2005 "Water for laboratory analysis", FS.2.2.0019.18 "Water for injection"
Type of current, frequency, voltage
alternating single-phase, 50 Hz, 220 V
Power consumption, kW
3,6
Overall dimensions (L×W×C), mm
424x417x454
Weight, kg
20,0
Livam
Belgorod
Produced in: Belgorod
Installation for obtaining analytical quality water UPVA-15
from
178 000 ₽
Capacity, l/h
15,0 (-10%)
Purpose
preparation of distilled water of type 2 according to GOST 52501-2005 "Water for laboratory analysis" FS.2.2.0019.18 "Water for injection"
Heating elements
Heating element 3.0 kW 220V (stainless steel) – 3 pcs.
The quality of the produced water
GOST 52501-2005 "Water for laboratory analysis", FS.2.2.0019.18 "Water for injection"
Type of current, frequency,
three-phase alternating voltage, 50 Hz, 380 V
Power consumption, kW
9,1
Overall dimensions (L×W×C), mm
550x500x625
Weight, kg
39.0
Livam
Belgorod
Produced in: Belgorod
Installation for obtaining analytical quality water UPVA-5-1
from
312 000 ₽
water type I: 5.0, water type II: 5.0
Purpose
obtaining super pure type 1 water according to GOST 52501-2005 "Water for laboratory analysis" FS.2.2.0019.18 "Water for injection"
Heating elements
Heating element 3.5 kW 220V (stainless steel) – 1 pc.
The quality of the produced water
according to the requirements for type I and II water according to GOST 52501-2005 "Water for laboratory analysis" and the articles of the FS.2.2.0019.18 "Water for injection"
Type of current, frequency, voltage
variable single-phase, 50 Hz, 220 V
Power consumption, kW
3,6
Overall dimensions (L×W×C), mm
670×470×490
Weight, kg
35.0
Livam
Belgorod
Produced in: Belgorod
Acoustic ultrasonic flow meter Volga ML
from
400 000 ₽
The flow meter is fully developed by Russian specialists in the field of acoustics, hydraulics and electronics, and is designed to measure the volumetric flow rate and volume of water in pipelines, mainly medium and large, under pressure, non-pressure and combined (pressure-free) flow modes. The flowmeter is based on ultrasonic "time-pulse" multipath technology for measuring the flow velocity in the measuring range. In addition, depth sensors (primary transducers) - hydrostatic, radar contactless, ultrasonic underwater or ultrasonic contactless - are used to measure the flow in water ducts with a combined or non-pressure flow mode. In the presence of deposits affecting the shape and area of the live section of the flow, sediment level sensors are used.
Secondary converter
It is available in both stationary (~220 V) and portable versions with autonomous power supply.
Primary converters
Inset and overhead primary converters from the inside allow you to place the measurement gate on any water pipe made of any material, taking into account design features.
Pipe sizes
Du, mm: 200, 250, 300, 350, 400, 500, 600, 700, 800, 900, 1000, 1200, 1400, 1600, up to 15000 mm
The Volga ML acoustic ultrasonic flowmeter is registered as a type of measuring instrument in the Federal Information Fund for Ensuring the Uniformity of Measurements for No. 78414-20 (MP 2550-0361-2019).
The Volga ML acoustic ultrasonic flow meter has been recognized as the winner in the nomination Best Technology of the International Environmental Award EWA Award 2020.
ICF VOLGA
Moscow
Produced in: Moscow
Non-pressure hybrid flow meter-counter Volga Triton
from
300 000 ₽
The Volga Triton pressure-free hybrid flow meter is designed to measure the volumetric flow of liquid in water ducts with a pressure-free and combined pressure-free flow mode. The submerged primary speed converter operates on the basis of the Doppler effect, emitting an ultrasonic signal towards the flow and receiving an echo reflected from particles in the flow with a frequency different from the frequency of the emitted signal. This frequency shift is called the "Doppler Shift" and it is proportional to the flow rate. A non-contact ultrasonic primary converter VBN-DG-01 or any other third-party liquid level converter with a unified current output of 4-20 mA can be used as a depth meter: radar, hydrostatic or ultrasonic.
The volumetric flow rate is determined both by the "area-speed" method and by MI2220-2013, depending on hydraulic conditions.
In non-contact (radar) mode, the Volga Triton flowmeter is designed to measure the volumetric flow rate of a liquid in a non-pressurized flow mode. The flow meter can be used as part of waste water metering units in non-pressure (gravity) sewage systems, open irrigation and reclamation channels, open or underground derivational non-pressure water pipelines of hydropower facilities, diverting supply and recirculation water pipelines of thermal power and other hydraulic structures with a non-pressure flow regime. The measurement technology is based on a non-contact radar method for measuring surface flow velocity and a non-contact ultrasonic/radar method for measuring water level.
As a water level meter, both the proprietary ultrasonic level sensor BP-G-01 and third-party sensors connected via unified digital or analog interfaces, for example, VEGAPLUS, can be used.
The pressure-free hybrid flow meter "Volga Triton" became the winner of the International Environmental Award EWA Award 2021 in the nomination Best technology.
Secondary converter
It is available in both stationary (~220 V) and portable versions with autonomous power supply.
Primary converters
VBN-DS-01 Primary speed converter for medium and large water pipelines
VBN-DS-02 Combined primary speed and depth converter for medium and small aqueducts
VBN-DS-03 is a combined low-profile primary speed and depth converter for small aqueducts.
VBN-DG-01 - contactless ultrasonic primary transducer - depth meter
Pipe sizes
Du, mm: 350, 400, 500, 600, 700, 800, 900, 1000, 1200, 1400, 1600, up to 6000 mm
ICF VOLGA
Moscow
Produced in: Moscow
Installation for obtaining analytical quality water UPVA-25
from
199 000 ₽
Capacity, l/h
25,0 (-10%)
Purpose
preparation of distilled water of type 2 according to GOST 52501-2005 "Water for laboratory analysis" FS.2.2.0019.18 "Water for injection"
Heating elements
Heating element 2.7 kW 220V (stainless steel) – 6 pcs.
The quality of the produced water
GOST 52501-2005 "Water for laboratory analysis", FS.2.2.0019.18 "Water for injection"
Type of current, frequency,
three-phase alternating voltage, 50 Hz, 380 V
Power consumption, kW
16.3
Overall dimensions (L×W×C), mm
660x550x760
Weight, kg
50,0
Livam
Belgorod
Produced in: Belgorod
Vacuum drying cabinet SNVS-50/3.5
They are designed for carrying out various technological processes at temperatures from 40 to 500 oC, in vacuum up to 1x10−3 mmHg, or in an inert gas of high purity.
They are used for drying, light annealing, aging, low and medium tempering in an oxidizing environment, degassing of ferrous and non-ferrous metals (including copper and copper alloys), or any other materials processed under similar conditions.
The program setting of heat treatment modes including vacuuming, high purity inert gas intake with repeated vacuuming allows heating in an oxidizing environment with high purity of the surfaces of the processed parts, without scale formation and oxidation.
Tula-Term
Tula
Produced in: Tula
Collection for storage of purified water S-100
from
79 000 ₽
Designed for collecting, storing and distributing purified water obtained by various purification methods, with a capacity of 100 liters and 100% stainless steel, which allowed for a long service life.
Dimensions in terms of 560x580 mm
Weight 13.5 kg
Livam
Belgorod
Produced in: Belgorod
Muffle furnace LF-9/11-G1
Design features:
Durable ceramic muffle;
Closed heaters on four sides of the chamber;
Microprocessor temperature controller;
Conveniently located control panel and bright LED display;
Ease of management and control;
LED indicators of heater operation and protection operation;
Automatic shutdown of heating when opening the door;
The door opens up and faces the user with the cold side;
Alarm when the current temperature exceeds the limits of the permissible range;
Highly efficient thermal insulation of the housing;
The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint.
Technical specifications:
Maximum heating temperature, °C +1100
Temperature stability in steady-state thermal mode, °C ± 10
Warm-up time to maximum temperature, no more than 120 min
Dimensions of the working chamber, WxHxD, not less than 200x150x290 mm
Overall dimensions, WxHxD, not more than 525x625x620 mm
Rated supply voltage, 220 V
Rated power, W 5500
LOIP
Saint Petersburg
Produced in: Saint Petersburg
2NVBM-250/3000 Booster high vacuum pump
The 2NVBM-250(R)/3000 booster pump consists of housings, a steam pipe, a trap and a heater. The alignment of the steam line in the pump housing 2NVBM-250(R)/3000 is carried out by a steam line screed, which, when installing the housing on the collector, enters its upper end into the hole of the hood (oil reflector). The required effective speed of action of the forevacuum pump (pumps) at a pressure of 200 Pa (1.5 mm Hg) at the outlet of the 2NVBM-250(R)/3000 booster pump is not less than 25 l/s. The maximum residual pressure of the 2NVBM-250(R)/3000 pump measured by the PMI-2 manometric ionization converter with nitrogen filled into its trap, is no more than 6.6 × 10-4 Pa (5 × 10-6 mm Hg). The pressure of the cooling water at the inlet to the 2NVBM-250(R)/3000 pump should be from 0.2 to 0.5 MPa (from 2 to 5 kgf / cm2). The drain from the pump must be free with a jet break. Cooling water consumption is 360 l/h.
The total amount of working fluid for the 2NVBM-250(R)/3000 pump is 17 liters, the level of the working fluid should be between the upper and lower marks of the level gauge. Replacement or refilling of the working fluid depends on the operating mode of the pump (inlet pressure, pumping duration, etc.) and the composition of the pumped medium, so the time after which the working fluid is replaced or refilled can be 100 hours or more. A large flow rate of the working fluid is observed when the pump is operating in the input pressure range from 1.33 to 13.3 Pa (from 1 · 10-2 to 1 · 10-1 mm Hg). The operating mode of the pump in the range from 13.3 Pa (0.1 mmHg) to the maximum residual pressure is cyclically irregular.
Vakuummash
Kazan
Produced in: Kazan
Muffle furnace LF-15/11-V1
Design features:
Special system of air intake and exhaust of combustion products with adjustable thrust;
Durable ceramic muffle;
Closed heaters on four sides of the chamber;
Microprocessor temperature controller;
Conveniently located control panel and bright LED display;
Ease of management and control;
LED indicators of heater operation and protection operation;
Automatic shutdown of heating when opening the door;
The door opens up and faces the user with the cold side;
Alarm when the current temperature exceeds the limits of the permissible range;
Highly efficient thermal insulation of the housing;
The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint.
Technical specifications:
Maximum heating temperature, °C +1100
Temperature stability in steady-state thermal mode, °C ± 10
Warm-up time to the maximum temperature, no more than 120 min
Dimensions of the working chamber, WxHxD, not less than mm 215x190x330
Overall dimensions, WxHxD, not more than 525x1045x680 mm
Rated supply voltage, 220 V
Rated power, W 6000
LOIP
Saint Petersburg
Produced in: Saint Petersburg
Muffle furnace LF-7/13-V2
Design features:
Special system of air intake and exhaust of combustion products with adjustable thrust;
Programmable microprocessor temperature controller;
Three programs of ten steps with the ability to set the temperature, heating speed and holding time for each step;
Manual heating mode with timer with sound notification and auto-off;
Durable ceramic muffle;
Semi-open heaters on four sides of the chamber;
Backlit graphic display;
Conveniently located control panel;
Automatic shutdown of heating when opening the door;
Sound and light alarm when the current temperature exceeds the limits of the permissible interval;
Highly efficient thermal insulation of the housing;
The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint.
Technical specifications:
Maximum heating temperature, °C +1300
Temperature stability in steady-state thermal mode, °C ± 10
Warm-up time to the maximum temperature, no more than 120 min
Dimensions of the working chamber, WxHxD, not less than 200x110x285 mm
Overall dimensions, WxHxD, not more than mm 505x955x655
Rated supply voltage, 220 V
Rated power, W 3300
LOIP
Saint Petersburg
Produced in: Saint Petersburg
Circulation thermostat LT-111b
Technical specifications:
Temperature range:
without external cooling, °C
Current+10 ... +100
with tap water cooling °C
Tvods+5 ...+100
Accuracy of temperature maintenance, °C ± 0.1
The error of setting the set temperature, no more than ° C ± 0.2
Heater power, W 1900
Pump:
max. flow rate, l/min 7.5
pressure, 0.17 bar
Bath volume, l 11
The working fluid is water, water-glycerin mixture.
The open part of the bath / depth, mm 160x240/200
Overall dimensions, mm 268x335x420
Weight, kg 10
LOIP
Saint Petersburg
Produced in: Saint Petersburg
Muffle furnace LF-15/13-G2
Design features:
Programmable microprocessor temperature controller;
Three programs of ten steps with the ability to set the temperature, heating speed and holding time for each step;
Manual heating mode with timer with sound notification and auto-off;
Durable ceramic muffle;
Semi-open heaters on four sides of the chamber;
Backlit graphic display;
Conveniently located control panel;
Automatic shutdown of heating when opening the door;
Sound and light alarm when the current temperature exceeds the limits of the permissible interval;
The door opens up and faces the user with the cold side;
Highly efficient thermal insulation of the housing;
The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint.
Technical specifications:
Maximum heating temperature, °C +1300
Temperature stability in steady-state thermal mode, °C ± 10
Warm-up time to the maximum temperature, no more than 120 min
Dimensions of the working chamber, WxHxD, not less than mm 215x190x330
Overall dimensions, WxHxD, not more than mm 525x655x680
Rated supply voltage, 220 V
Rated power, W 6100
LOIP
Saint Petersburg
Produced in: Saint Petersburg
Laboratory shaft furnaces SSHOL SSHOL 35/11
The furnaces can be used as universal laboratory furnaces in metallurgical, jewelry and ceramic production, in orthopedic dentistry, chemical and food laboratories.
Technical specifications
Universal laboratory shaft furnaces with software control SSHOL are used for firing products, melting and heat treatment of metals at temperatures up to 1150 ° C.
Max. operating temperature- 1150 ⁰C
Dimensions of the working chamber - Ø300x500 mm
MIUS
Tula
Produced in: Tula
LB186 Laboratory bath
It is designed to solve temperature control problems that do not require high accuracy of maintaining the temperature of the coolant and the uniformity of the temperature field in the working volume.
Laboratory bath LB186 is characterized by simplicity of design, ease of use, reliability and low cost in comparison with liquid thermostats.
Bath volume 140 l
Overall dimensions 1150x570x480 mm
The open part of the bath is 1060x430 mm
Bath depth 300 mm
Weight 58 kg
Power consumption 2.5 kW
Termeks
Tomsk
Produced in: Tomsk
LI-400 Integrated Vacuum Trap
The LI-400 integrated flanged trap is installed inside the diffusion pump instead of the standard oil reflector, without increasing the overall dimensions of the diffusion pump.
The LI-400 trap performs the function of an oil reflector, is installed instead of a standard oil reflector in pumps, has an additional number of cooled screens for capturing oil return flow vapors (more than that of the MU trap), covers the entire area of the input high-vacuum flange.
Vakuummash
Kazan
Produced in: Kazan
Vacuum drying cabinet with manual control SNVS-215/3.5
from
896 374 ₽
The SNVS-215/3.5 vacuum drying cabinet with a volume of 215 liters with manual vacuum adjustment is designed for heat treatment of materials at temperatures up to 350 with air access and in a vacuum controlled by manual valves. Thanks to modern temperature control, it demonstrates excellent performance of heat treatment modes. The measurement system complies with Russian standards and has certificates of entry into the SI State Register. Design for heat treatment in production and clean laboratories. The cabinet can be equipped with a software control device with an automatic timer and a wide selection of additional options.
Tula-Term
Tula
Produced in: Tula
Furnace control cabinet SHUP-160-1
Designation
SHUP-160-1
Switching power, kW
160
Automatic switch, A
320
Supply network voltage, V/Hz
380
Tula-Term
Tula
Produced in: Tula
MM-180/20/35 POZIS Medical freezer
from
58 660 ₽
Refrigerant
404a
Total volume, l.
180
The volume of the freezer / NTO, l.
180
Number of compressors, pcs.
1
Height, mm
870
Height with wheels, mm
940
Depth, mm
720
Width, mm
1310
Weight, kg., no more
80,5
Rated power consumption, W
250
Maximum rated power, W
275
Voltage,
220 V
Warranty,
1 year
Final report on pre-qualification for compliance with the requirements of Good Practice of the EAEU Distribution: yes
Freezer compartment
The temperature in the freezer, °C
-18...-40
Thermal card: yes
Efficiency and energy consumption
Electricity consumption at t storage -18°C and t roc +25°C, kWh/day, no more
than 0.81
Climate class
UHL 4.2 (i.e. for moderate and cold climate)
Frequency, Hz
50
Approximate dimensions of the product with packaging
Net weight of the product, kg
80,5
Gross weight of the product, kg
93.5
Volume of packaging, m3
0,965
The length of the package, m
0,75
Width of the package, m
1.34
Height of the package, m
0.96
POZIS
Зеленодольск
Produced in: Zelenodolsk, Tatarstan
Thermal collector for sterile solutions TS-100
from
334 200 ₽
Allows you to accumulate 100 liters of injection water. It is equipped with a heating and recirculation system, a temperature control meter, as well as special air bactericidal filters through which contact with the atmosphere is carried out. The automation system regulates the operation of the pump and heating elements and provides automatic shutdown of the distiller when filling the tank. It consists of 100% stainless steel, which allowed for a long service life.
Overall dimensions (LxWxH) 1200×585×1120 mm
Weight 55 kg
Livam
Belgorod
Produced in: Belgorod
LB21-Sh Laboratory bath
It is designed for thermostating samples in glasses, flasks and other laboratory utensils in cases when high accuracy of temperature maintenance is not required and good uniformity of the temperature field in the working volume is not needed.
The operating temperature range is Current +5...+200 °C.
One workplace with a diameter of 110 mm with five steel O-rings, a tripod and a foot with a clip.
Stamped steel bath with a volume of 3.5 liters and a depth of 60 mm.
Bath volume 3.5 l
Overall dimensions 515x360x610 mm
The open part of the bath is 295x145 mm
Bath depth 60 mm
Weight 6.5 kg
Power consumption 2.5 kW
Termeks
Tomsk
Produced in: Tomsk
Electric resistance chamber vacuum furnace SNVS-1.5.2.0/10SHM10
The electric furnace SNVS-1,5.2,0/10SHM10 is designed for heat treatment in vacuum, according to the technological process. The execution Of The Electric Furnace is mine. The type of cage is monoblock or composite. The loading direction is vertical. The loading method is by universal shop lifting mechanisms.
Tula-Term
Tula
Produced in: Tula