Search

The NV-1500 SM-B is a specialized table for microscopy. The table top is 70 cm deep with a small cutout made of laminate. It is designed for sitting work: the height from the floor to the countertop is 75 cm (this is the height of a regular office desk). External dimensions of the table (W×D×H): 1500×700×750 mm. A small superstructure allows you to compactly place the necessary drugs and accessories next to the workplace. Its dimensions: (W×D×C): 668×120×200 mm. The table top is made of laminated chipboard. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents and is well suited for the placement of devices. There is a small semicircular cutout on the front of the table top, which allows you to work more comfortably with the microscope. The side laminated panels of the table (chipboard 16 mm thick) are edged with a PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor.

A single-fiber converter 100base-FX, single-mode WDM, acSC connector, working distance from 20 to 80 km. The output optical power of the transmitter is -13~ -6 dBm, the sensitivity of the receiver is 36 dBm. Delivery of the product is possible in two versions: Media converters without DIP switch. Media converters that support the LFP (Link Fault Pass Through) (LLCF/LLR) function using the DIP switch. The LLCF/LLR function allows you to instantly receive information when communication problems occur and provide an effective solution for monitoring the network with the possibility of automatic redundancy. The DIP switch disables or enables the use of the LFP function.

The LAB-KMP kit is designed for testing the corrosion activity of petroleum products in accordance with GOST 6321-92 or ISO 2160. The kit is used in conjunction with LOIP LT thermostats and LOIP LB-200 precision thermostatic baths with a bath depth of 200 mm. The composition of the kit: GOST 6321-92 Tripod for test bombs 1 pc. Test bomb 2 pcs. Tripod for test tubes 1 pc. Test tube P-2-16/150 20 pcs. Cork cork 20 pcs. Copper plate (40x10x2 mm) 50 pcs. Sandpaper 10 sheets Corrosion standard 1 pc. ISO 2160 Tripod for test bombs 1 pc. Test bomb 2 pcs. Tripod for test tubes 1 pc. Test tube P-2-26/150 11 pcs. Cork cork 11 pcs. Copper plate (75x12x2 mm) 50 pcs. Sandpaper 10 sheets Corrosion standard 1 pc.

The analyzer automatically heats the sample crucible and moves the test flame. The flash moment is set visually and recorded by pressing the "STOP" button, while the flash temperature is displayed on the display. Technical specifications: Flash temperature measurement range (with crucible cooling), °C from +40 to +400* The heating rate of the crucible with the sample, °C/min 0..20 Igniting a gas flame The speed of the stirrer, rpm 30...240 Power consumption from AC 220 V, no more, 600 W Overall dimensions of the device, not more than 350x250x280 mm Weight of the device, not more than, kg 8

Temperature setting range, oC +35…+95 Temperature error, oC ±1.0 is protected from excess temperature RAINBOW TSR-150S F-C Hydraulic thermostat Supply voltage, V 230+-10% Current consumption 3.3 A Power consumption, 750 W Overall dimensions L x W x H, mm 380 x 300 x 190 Overall dimensions of the bath L x W x H, mm 290 x 300 x 140 Total/ engine capacity, 12.0/9.0 l

The NV-800 SHP cabinet is designed for storing labware. It has 2 shelves-inserts, 2 glass shelves, 4 drawers. The cabinet is made of laminated chipboard with a 2 mm shockproof PVC edge on the facades. Included in the set: - glass doors on top; - 2 glass shelves 5 mm thick; - 4 drawers in the lower compartment; - 1 door and 2 shelves-inserts for the lower compartment; - metal legs 100 mm high.

Furniture for laboratory work. Table-sink on a support pedestal made of metal LAB-M MO ME 150.60.90 PP Width: 1500 Depth: 600 Height: 900 Package contents: table top – a single module made of polypropylene Attention! It is not recommended to use it for work with oil and petroleum products (fuel oil, bitumen, etc.) The inner size of the bowl – 500*400*285 mm The base of the sink table is a metal support pedestal. All-welded frame painted with dark grey powder paint RAL 7011. The bottom and top of the housing are sheet steel painted with powder paint of dark gray RAL 7011, the side walls are made of sheet steel painted with powder paint of white RAL 9016. Facades – laminated MDF of white color with a thickness of 16 mm, dark gray ABS edging

It is intended for painting blood smears or other biological preparations on slides - slides by the group method (slides are placed in holders) according to a given technological program in diagnostic and research laboratories. Cassettes with fixed slides successively go through 5 working stages: 1) Pre-drying of freshly prepared preparations; 2) Fixation with pre-painting; 3) Basic coloring; 4) Flushing; 5) Drying. The cassettes are moved to the next position by the forward-return movement of the trays. The time of each stage is the same. It can be set when ordering the device. Factory setting – 5 minutes. The total duration of all stages is 20 minutes. The coloring process is carried out along a linear trajectory. Slides with a smear should be placed in special cassettes and fixed by turning the eccentric lever. Fill the baths with reagents and install them in the device at the specified places. Place the slide cassette on the pre-drying starting position. If the preparations are dry, the cassette with slides should be immediately placed in a bath with a retainer. The time of each stage is 5 minutes. The whole procedure of painting and drying takes no more than 20 minutes. With sequential installation, the device can process up to 12 cassettes, i.e. up to 120 slides per hour.

equipment sink-drain (polypropylene, internal size 250*100*150mm), laboratory faucet for water the scope of delivery includes a siphon corrugated hose flexible liner length 1200mm rack support racks – aluminum profile painted with powder paint (RAL 1001) top panel depth 190mm – metal painted with powder paint (RAL 1001)

KLM-C650-1-5 laser modules are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.

The submersible smart probe L=150 mm SZPG.150 is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor, Android program installed. Operating conditions of the SZPG.150 smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the SZPG.150 smart probe Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

The characteristics of the device are similar to the GCHA-18D model; The difference is that the oil–free compressor built into the GCHA-18D-K generator provides complete autonomy of the device. The warranty for the device is 18 months, for the built-in compressor - 12 months from the date of sale. Technical specifications The grade of nitrogen produced according to GOST 9293-74 is high purity, grade I The volume fraction of nitrogen is not less than, % vol. (including impurities of inert gases: argon, neon, helium) 99,999 The volume fraction of oxygen is not more than, % vol. (ppm) 0.0005 (5 ppm) The volume fraction of water vapor is not more than, % vol. (ppm) 0.0007 (7 ppm) The volume fraction of hydrogen is not more than, % vol. (ppm) 0.0002 (2 ppm) The volume fraction of the sum of carbon-containing compounds in terms of methane is not more than, % vol. (ppm) (with a concentration of methane in the supply air not more than 5 ppm)* 0.00001 (0.1 ppm) Maximum nitrogen capacity is not less than 18 liters/hour (300 ml/min) Nominal output pressure of nitrogen is 4 ati The time of setting the operating mode for single-shift operation is no more than, min, * 45 Noise level generated by the compressor is no more than 45 dB Power consumption is not more than 300 VA Overall dimensions, (width x depth x height) are not more than, mm 230x470x510 Weight, not more than, kg 25 Working conditions: Ambient temperature, °C from +10 to +35 Electric power supply from a single-phase AC network with a voltage of 220 ± 10% and a frequency of 50 ± 1 Hz Average full service life is at least 6 years The generator for electrical safety meets the requirements of Class 1, type H according to GOST 12.2.025-76