TEKHNO-AS

The smart probe of relative humidity and temperature L=150 mm with a built-in flash memory is designed to measure the temperature of gaseous materials without mechanical impurities and aggressive vapors, relative humidity by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor based on the Android program. Operating conditions of the SZVL.150P smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the smart probe SSVL.150P Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor based on the Android program. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor based on the Android program. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

The high-precision smart surface probe L=150 mm SZPVT.150 is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor, Android program. Operating conditions of the SZPVT.150 smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the smart probe SZPVT.150 Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

The trace searching kit is designed to accurately determine the location and depth of underground utilities (power and signal cable lines, reinforced fiber-optic lines, pipelines made of electrically conductive materials), troubleshooting cable lines, and also allows you to conduct a survey of the area in the shortest possible time and with great reliability before excavation and to prevent damage to engineering communications. As part of the kit, the receiver is in the form of a monoblock with a large LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line. Built-in GPS\GLONASS module for determining and recording the coordinates of the location of communication. "Probe" mode for tracing NON-METALLIC communications using an in-line generator (optional). The kit is equipped with the latest compact autonomous generator AG-107 with built-in batteries, display and built-in induction antenna, for tracing communication in a contactless way. The output power of the generator is up to 60 watts.

The meter-recorder IS-203.2 is a microprocessor-based meter designed to measure temperature. Equipped with a non-volatile storage device and a real-time clock. The device has two measuring channels. The measurement results are stored in the non-volatile memory with a volume of 15,000 measurements per channel. The operating conditions of the meter IS-203.2.0 Ambient temperature, ° C: -20...+50. Relative humidity, %: up to 90. Atmospheric pressure, kPa: 70...106.7. Scope of application of the meter IS-203.2.0 Control of technological processes in various industries, including: utilities, construction, food and pharmaceutical industries, agriculture, etc. Warehouses (grocery, industrial, pharmaceutical, etc.). Transportation (grocery, industrial, pharmaceutical, etc.). Functionality of the meter IS- 203.2.0 Temperature measurement by external sensors. Saving the measurement results in the device memory. Indication of the results of current measurements, time, channels included, interval between measurements, free memory of the device, battery capacity, serial number of the device, time of the next measurement. Operational start and stop of the measurement process. Data transfer to a PC via a COM port or USB.

Designed to measure the temperature of gaseous materials without mechanical impurities and aggressive vapors, atmospheric pressure. The smart atmospheric pressure probe with built-in flash memory is designed to measure the temperature of gaseous materials without mechanical impurities and aggressive vapors, atmospheric pressure by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor based on the Android program. Operating conditions of the SZDAP smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the smart probe SZDAP Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor. The Android program is installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor. The Android program isinstalled. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

Multifunctional trace searching kit for finding underground utilities (cable lines, metal pipelines and other communications made of conductive materials). The presence of an acoustic sensor and a shock mechanism allows tracing NON-METALLIC pipelines, as well as searching for leaks from pipelines and searching for cable damage sites. The isolation monitoring sensors DKI-117 and the sensor-detector of communication defects DODK-117 search for places of damage to the external insulation of communication. The kit includes the most powerful multi-frequency generator with a range of up to 10 km. Connection to the desired route is possible both by contact and contactless method.

Designed to measure the temperature of various materials by direct contact of the probe with the measuring object The smart air probe L=1000 mm SSV.1000 is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor. Android program is installed. Operating conditions of the SZV.1000 smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the smart probe SSV.1000 Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor. Android program is installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

Description of the cable finder Success KBI-309M • – A traceroute receiver in the form of a monoblock with a frost-resistant LCD display. • – Graphical representation of the route on the device screen. • – Automatic calculation and display of the depth of the communication up to 10 m, as well as the current in the line. Purpose of the cable finder Success KBI-309M • – Search for live electrical cables. • – Search and tracing of underground utilities (gas pipelines, pipelines, power and telephone cables). • – Determination of the occurrence of underground utilities at a depth of up to 10 m. Features of the AP-019M receiver • – Modern digital tracer receiver-monoblock AP-019M. • – The image of the route on the device screen. • – Automatic calculation and display of the depth of communication and current in the line. • – Several options for displaying information on the receiver indicator: "Route", "Graph", "Graph+", "Minimum maximum" and "2-frequencies" allow the operator to use the device's capabilities as efficiently as possible. • – Additional functions when connecting external sensors. • – Wide range of operating frequencies (50(60) / 100(120) / 512 / 1024 / 8192 / 32768 Hz, wide band 40...8000 Hz, radio 8...40 kHz). • – Frost-resistant, working at temperatures up to -30 ° C. • – Menu in two languages (Russian and English).

The kit is designed to measure the temperature of ferrous metal melts. It consists of a digital contact thermometer TK-5.27 complete with a submersible high-temperature probe, designed to measure the temperature of metal melts in the range of +600 ° C ... +1800 ° C. The digital contact thermometer TK-5.27 is equipped with the function of recording measurements in the device's memory, followed by transferring data to a computer and providing reports in the form of tables and graphs. To measure the temperatures of metal melts, disposable thermocouples of the PPR (B) type with a protective tube length of no more than 900 mm are used. The kit is adapted to the replacement blocks of EVRAZTEMP ET-V-09-00. •

High-precision cmart surface probe L =500 mm SZPWT.500P with built-in flash memory is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor, Android program installed. Operating conditions of the SZPVT smart probe.500P Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the SZPVT smart probe.500P Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

A trace searching kit for finding underground utilities (cable lines, metal pipelines, and other communications made of conductive materials), as well as the ability to search for places of damage to the external insulation of communications. The kit includes a receiver in the form of a monoblock with a frost-resistant LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line and the most powerful multi-frequency generator in the TECHNO-AC line, with a range of up to 10 km. Connection to the desired route is possible both by contact and contactless method.

The set is correlational-acoustic with two radio channels, the ability to trace metal and non-metallic pipelines (by acoustic method and in the "Probe" mode) with the function of saving GPS/GLONASS coordinates and the function of diagnosing shut-off valves. Designed for: – determination of the location of liquid leakages from pipelines by the correlation method; – tracing underground utilities; • – tracing of non–metallic pipelines by acoustic method and in the "Probe" mode; - clarification of leakage sites by acoustic leak detector; – diagnostics of shut-off valves; – search for damage to cable lines by induction and acoustic (together with GVI) methods; – creation of an information database on the condition of pipelines and the results of pipeline diagnostics.