TEKHNO-AS

The surface smart probe L=500 mm SZPV.500 is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor based on the Android program. Operating conditions of the SZPV.500 smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the SZPV.500 smart probe Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor based on the Android program. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor based on the Android program. Automatic transition to sleep mode after 50 seconds. The ability to connect external power. Possibility of calibration.

It is designed to measure the temperature during the transportation of petroleum products, namely, to make a temperature correction for the volumetric expansion of petroleum products. The density of petroleum products decreases significantly with increasing temperatures, and the volume of the product increases, the kit "Oilman-1" allows temperature measurements for the subsequent calculation of the volumetric expansion of petroleum products. •

The wall-mounted amsrt air probe is designed to measure the temperature of gaseous materials without mechanical impurities and aggressive vapors by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor based on the Android program. Operating conditions of the smart probe SZVN Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the smart probe of the SSVN Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor. The Android program is installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor. The Android program isinstalled. Automatic transition to sleep mode after 50 seconds. The ability to connect external power. Possibility of calibration.

High-temperature smart surface probe L=300 mm SZPVV.The 300P with built-in flash memory is designed to measure the temperature of various materials by directly contacting the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor, Android program installed. Operating conditions of the SZPVV smart probe.300P Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the SZPVV smart probe.300P Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

A trace searching kit for searching underground utilities (cable lines, metal pipelines, and other communications made of conductive materials). The kit includes a receiver in the form of a monoblock with a large LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line, as well as a compact autonomous generator with an output power of up to 20 watts and a range of up to 3 km. Connection to the desired route is possible both by contact and contactless method.

The purposes of the ETL TECHNOAS 2 laboratory based on Gazelle Next NN are: • – Testing and searching for damage to cable lines up to 10 kV + SNF (cross–linked polyethylene); • - Posititioning of the location and depth of underground utilities (power and signal cables); • – Identifying the nature of the damage and the distance to the damage site without burning the cable insulation; • – Testing of the cable with alternating high voltage; • – Tests of power cables and cable sheaths with cross-linked polyethylene insulation; • – Measurement of insulation resistance of electrical circuits. ETL TECHNOAS 2 laboratory based on Gazelle Next NN consists of following parts standartly: 1. – Color design; 1. – Laboratory compartment; 1. – Partition between compartments; 1. – Windows: rear side-blind, there is a plastic window with a cable coupling in the rear door; 1. – A 10x10 hatch in the lower right corner for cable output; 1. – Finishing of sidewalls and ceiling; 1. – Floor covering: autolinoleum; 1. – On-duty lighting: standard; 1. – Working lighting: fluorescent lamps; 1. – Furniture: main stand, soft seat. Electrical safety system of ETL TECHNOAS 2 laboratory based on Gazelle Next NN incledes following parts: • – MKZ safety control module; • – Locking switches on the doors of the in/out compartment; • – Audible alarm; • – Light alarm; • – Emergency shutdown button; • – Input release with visible contact break. Additional equipment of ETL TECHNOAS 2 laboratory based on Gazelle Next NN includes: • – 12/220 V voltage converter; • – Diesel/gasoline generator (for field operation); • – Laboratory power management system; • – Additional heater; • – Air conditioning.

Designed to measure the temperature of various materials by direct contact of the probe with the measuring object. A smart probe for connecting an external thermoelectric converter with a built-in flash memory is designed to measure the temperature of various materials by directly contacting the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor. The Android program is installed. Operating conditions of the SZVTP smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. The functionality of the smart probe SSVTP Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor. The Android program is installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor. The Android program isinstalled. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

The Smart submersible reinforced probe L=1500 mm SZPGU.1500 is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor, Android program installed. Operating conditions of the SZPGU.1500 smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the smart probe SZPGU.1500 Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

The automatic tracer pulse generator "AG-114.1" is designed to create propagating signals (vibrations) in the routes of hidden communications with the active method of tracerouting. The device creates an alternating sinusoidal current in the studied communication (constantly or in short-term parcels) necessary to determine its location. The features of the AG-114.1 generator The selected output power (5 W at 1...1000 ohms, 10 W at 1...500 ohms, 20 W at 1...250 ohms) is issued automatically. The ability to work on such high load resistances allows you to trace very extensive communications. Low power provides energy saving and small "readjustments" to neighboring objects, high power provides a high range of broadcast and detection. Three generation modes: pulse – the main high-efficiency mode with high intelligibility against the background of interference; continuous – an additional low-cost mode for short-term special measurements; three–frequency mode, which provides the selection of the optimal frequency on a remote receiver without switching the transmitter (generator). Three generation frequencies: 512 Hz, 1024 Hz, 8192 Hz. Lower frequency – less "readjustment" to neighboring objects, higher frequency – higher detection range. Unusually compact (190x140x80 mm), for such a high output power (20 W), the autonomous design is provided by the use of highly efficient technology "CLASS D (BD)" (pulse output power amplifier with an efficiency of 80%). As a result, one small-sized autonomous battery with a capacity of only 2.2 Ah provides pulse generation for >5 hours at maximum output power (20 watts). It is possible to work with "recharge" from the charger or increase capacity by connecting an external battery to increase the time resource.

High-temperature smart surface probe L=500 mm SZPVV. 500P with built-in flash memory is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor, Android program installed. Operating conditions of the SZPVV smart probe.500P Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the SZPVV smart probe.500P Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect external power. Possibility of calibration.

The set is correlational-acoustic, with graphical indication of the communication axis and digital depth of occurrence. Designed for: • – determination of the location of leakages from pipelines by the correlation method; • – tracing underground utilities with the display of the communication axis and digital measurement of the depth of occurrence; • – built-in GPS/GLONASS module for saving coordinates with subsequent mapping of the communication route on the map; • – clarification of leakage sites by acoustic leak detector; • – creation of an information database on the condition of pipelines and the results of pipeline diagnostics; • – diagnostics of shut-off valves.

The smart submersible reinforced probe L=1000 mm SZPGU.1000P with built-in flash memory is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor, Android program installed. Operating conditions of the SZPGU.1000P smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the SZPGU.1000P smart probe Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.