TEKHNO-AS

The smart probe for connecting an external thermoelectric converter SZVTN is designed to measure the temperature of various materials, relative humidity, atmospheric pressure by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor based on the Android program. Operating conditions of the SZVTN smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. The functionality of the smart probe SZVTN Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor based on the Android program. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitorbased on the Android program. Automatic transition to sleep mode after 50 seconds. The ability to connect external power. Possibility of calibration.

A digital multifunctional tracer device with a large LCD display and sound output both to the built-in speaker and to the operator's headphones. Purpose of the cable finder Success KBI-406N • – Search for live electrical cables. • – Search for places where the pipeline and cable intersect. • – Determination of the occurrence of underground utilities at a depth of up to 6 m. • – Survey of the territory before excavation. Features of the AP-027 receiver • – Digital traceroute receiver. • – Large LCD display with switchable operating modes. • – Audio signal output both to the built-in speaker and to the operator's headphones. • – Wide range of operating frequencies (50 / 100 / 512 / 1024 / 8192 / 32768 Hz, Wide Band 50...8600 Hz). • – Possibility to additionally connect an acoustic sensor (leak detector / flaw detector function). • – Enclosure protection class IP54.

A trace searching kit for finding underground communications (cable lines, metal pipelines, and other communications made of conductive materials) with a digital tracerouting receiver. The kit is equipped with a compact stand-alone generator with a display and a built-in induction antenna. The output power of the generator is up to 20 watts and the operating range is up to 3 km. Connection to the desired route is possible both by contact and contactless method.

Designed to measure the temperature of various materials by direct contact of the probe with the measuring object. The smart air probe L=150 mm SSV.150 is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor. Android program is installed. Operating conditions of the SZV.150 smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the smart probe SSV.150 Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

The smart probe of relative humidity and temperature L=1000 mm with a built-in flash memory is designed to measure the temperature of gaseous materials without mechanical impurities and aggressive vapors, relative humidity by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor based on the Android program. Operating conditions of the SZVL.1000P smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the smart probe SSVL.1000P Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor based on the Android program. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor based on the Android program. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

The trace searching kit is designed to accurately determine the location and depth of underground utilities (power and signal cable lines, reinforced fiber-optic lines, pipelines made of electrically conductive materials), troubleshooting cable lines, and also allows you to conduct a survey of the area in the shortest possible time and with great reliability before excavation and to prevent damage to engineering communications. The kit includes a digital multifunctional tracking receiver with a large LCD display and audio output both to the built-in speaker and to the operator's headphones. Compact stand-alone generator with display and built-in induction antenna. The output power of the generator is up to 20 watts and the operating range is up to 3 km. Connection to the desired route is possible both by contact and contactless method.

The AG-107 generator is designed to create alternating current in electrically conductive communications with the electromagnetic method of tracerouting. Features of the AG-107 generator The main distinguishing feature is the small weight and dimensions of the device with high output power. The AG-107 generator has a built-in battery based on light high-capacity lithium-iron phosphate (LiFePO4) cells with low self-discharge, dimensions 216x180x105 mm, weight 1.8 kg and provides the following maximum output parameters: The output power in continuous operation is 30 watts; output power in intermittent operation mode is 60 W; Output voltage 60 V; current 5 A. The AG-107 generator uses a control interface similar to the AG-105 generator. The generator implements: Four sine wave generation frequencies: 512 Hz, 1024 Hz, 8192 Hz and 33 kHz; continuous, pulse and dual-frequency generation modes; built-in transmitting antenna operating at frequencies of 8192 Hz and 33 kHz; the possibility of connecting an external transmitting antenna and induction tongs; built-in "multimeter" displaying, at the operator's choice, the supply voltage or output parameters: current, power, voltage, load resistance; the ability to work from an external battery or from the mains ~ 220 V. The generator can be operated from an external power supply of 10...25 V. The generator is protected from the effects of voltages up to 400 V when connected to the communication and from exceeding the permissible voltage of the external power supply. The degree of protection of the case - case IP65 completely eliminates the penetration of dust and water jets inside when the lid is open.

A set of acoustic portable leakage detector with passive cable detection function "Success ATP-424N" is designed for: • – detection of leaks of liquids, heat carriers in pipelines located at a depth of up to 3 m in channel and channel-free laying; • – detection of energized power cables by passive method at a depth of up to 6 m.

The infrared pyrometer S-20.1 is used to monitor the condition of objects and technological processes in various industries and farms, as well as during scientific research. In this case, the dimensions of the studied surface of the object are determined by the angular field of view of the pyrometer.

The digital contact thermometer TK-5.29 is designed to measure the temperature of liquid, bulk, gaseous materials by immersion of measuring probes of thermometers into the medium (immersion measurements), contact measurements of temperatures of surfaces of solids (surface measurements), measurement of relative humidity of gaseous non-aggressive materials, measurement of atmospheric pressure, measurement of air flow velocity, as well as for measuring the luminous flux incident on a small area of the surface to its area and other physical quantities by sensors with a unified current output. The contact thermometer TK-5.29, depending on the order, is equipped with replaceable probes for various purposes. A probe of any type can be simultaneously connected to the TK-5.29 thermometer to the 1st channel, a thermal resistance sensor or a sensor with a unified current output of 4 ...20 mA to the 2nd channel. The TK-5.29 thermometer has the function of automatically determining the type of connected probe.

Purpose of the NEURONET TECHNOAS 4 Laboratory • – Universal educational complex of modern educational technologies; • – Mobile remote and educational office for the working coherence of the subjects of activity. The use of the NEURONET TECHNOAS 4 laboratory • – Hardware and software complex based on multifunctional neuro-modular systems of electroencephalographs-recorders "Encephalan-EEGR-19/26"; • – Improving the productivity and profitability of the work of teams with physio-psychological diagnostics and correction, with machine neuro-training on biofeedback; • – Biophysical individual adjustment of the central nervous system; • – Conscious development of new reflexive meaningful states, rapid assimilation of new knowledge, skills, skills and actions; • – Reduction of dangerous influences of the human factor in responsible professions (aviation and others); • – Improving the effectiveness of educational programs for special education, retraining and advanced training. NEURONET TECHNOAS 4 Laboratory Support System • – MKZ safety control module; • – Mass switches in all compartments; • – Smart Home system, continuous monitoring of all life support systems with video recording; • – Audible alarm; • – Light alarm; • – An autonomous power source from batteries with a 12/220 V voltage converter; • – 12 V - 220 V sockets; • – Hardware and software complex of neuro-modular systems of electroencephalographs-recorders "Encephalan-EEGR-19/26"; • – Hardware and software complexes of modern educational technologies integrated with the Central Control Unit (central control unit).

The combined laboratory up to 35 kV (ETL-35K) consists of: 1. Test facility • – Maximum rectified voltage up to 70 kV; • – Maximum AC voltage of the industrial frequency of 50 Hz to 100 kV. 2. Insulation parameters meter • – Transformation coefficient; • – No-load losses at low voltage; • – Short circuit resistance; • – Voltage and current; • – Power factor; • – Frequency of the measured voltage (current); • – Phase shift angle between voltage and current; • – Measurement of the active resistance of the windings. 3. Burning facility • – Maximum voltage up to 30 kV; • – Maximum current up to 80 A; • – Working hours are not limited; • – Switching of stages is carried out without breaking the arc at the time of switching; • – The ability to start working from any stage of burning (when working with low-voltage cables); • – Built-in afterburning. 4. High voltage pulse generator • – Output voltage 0...12 kV / 0...24 kV; • – The pulse energy at each stage is 3000 J; • – Built-in IDM for collaboration with the reflectometer. 5. Reflectometer – Supports 3 methods of determining the location of damage: • – By pulse reflectometry; • – By the method of oscillatory discharge; • – Pulse-arc method. 6. High-voltage cable defects detector • – Determining the location and depth of the cable at a depth of up to 10 m; • – Tracing at a distance of up to 10 km; • – Search for live electrical cables; • – Search for places where pipelines and cables intersect; • – Determining the places of damage to cable lines; • – Site surveys before excavation; • – Search for places of damage to the external insulation of the cable; • – GPS\GLONASS coordinates recording and mapping of found communications; • – Cable selection from the bundle; • – Search for the place of damage by acoustic method.