TEKHNO-AS

Appointment Athlete KAI-2.1001 • Determination of the type of damage and the distance to the place of damage to the cable. • Tracing a cable line up to 10 km. • Determination of cable depth up to 6 m. • Troubleshooting of cable lines by induction method. • Troubleshooting of cable lines by acoustic method. • Cable insulation testing.

Designed for: – measurement and registration of air temperature, temperature of hot water supply, surface of heating devices; – measurement and registration of relative humidity; – saving data to a memory card with subsequent transfer to a PC for generating reports; – measurement accuracy from ± 0.2 ° C.

The automatic tracing generator AG-144.1 is designed to create propagating signals in the routes of hidden communications with active methods of tracing (electromagnetic and acoustic). The device creates in the studied communication an alternating sinusoidal current necessary to determine its location or sound pulses using a shock mechanism. Sinusoidal generation (electromagnetic traceroute method) The selected power levels are issued automatically and are in offline mode: 7.5 W at 0.1...1300 ohms, 15 W at 0.15...660 ohms, 30 W at 0.3...1300 ohms, 60 W at 0.6...660 ohms - CONTINUOUSLY, or 15 W at 0.15...660 ohms, 30 W at 0.3...330 OHMS, 60 Watts at 0.6... 660 ohms, 120 watts at 1.2... 330 ohms - PULSES. When using an additional 12/24 V external battery (for example, a car), an output power of 45 watts at 0.45...2000 ohms, 90 watts at 0.9...1000 ohms CONTINUOUSLY, or 90 watts at 0.9... 1000 ohms, 180 watts at 1.8...500 ohms – PULSES can be achieved. The ability to work on such high load resistances allows you to trace very extensive communications. Low power provides energy saving and small "readjustments" to neighboring objects, high power provides a high range of broadcast and detection. Three generation modes: pulse – a highly economical mode with high intelligibility against the background of interference is good for interfacing with analog (mainly single-sensor) receiving systems; continuous – mode is required for most multi-sensor digital receiving systems; three–frequency mode, which provides the selection of the optimal frequency on a remote receiver without switching the frequency of the transmitter (generator). Three generation frequencies: 512 Hz, 1024 Hz, 8192 Hz. Lower frequency means less "readjustment" to neighboring objects and higher broadcast range, higher frequency means higher receiver sensitivity, but greater signal attenuation in "long" communication.

The smart submersible reinforced probe L =1500 mm SZPGU.1500P with built-in flash memory is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor, Android program installed. Operating conditions of the SZPGU.1500P smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the smart probe SZPGU.1500P Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

Digital tracer device with LED scale and audio output to the operator's headphones. Extremely easy to use and in a compact, lightweight case. Designed for: • – search for live electrical cable lines. • – search for places where the pipeline and cable intersect. • – determination of the occurrence of underground utilities at a depth of up to 6 m . Features of the AP-014 receiver • – Digital traceroute receiver. • – Additional LED indication of the signal level. • – Wide range of operating frequencies (50 / 100 / 512 / 1024 / 8192 / 32768 Hz, Wide Band 50...2000 Hz). • – Frost-resistant, working at temperatures up to -30 ° C. • – Lightweight, compact housing.

An affordable kit for searching underground utilities (cable lines, metal pipelines, and other communications made of conductive materials). The kit is equipped with a compact autonomous generator with an output power of up to 20 watts and a range of up to 3 km. Connection to the desired route is possible both by contact and contactless method.

Designed to measure the temperature of various materials by direct contact of the probe with the measuring object The high-precision air smart probe L=150 mm CVV.150 is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor based on the Android program. Operating conditions of the SZVV.150 smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the smart probe CVV.150 Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor. The Android program is installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

High-precision smart surface probe L =150 mm SZPWT. 150P with built-in flash memory is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor, Android program installed. Operating conditions of the SZPVT.150P smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the SZPVT.150P smart probe Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmission of data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect external power. Possibility of calibration.

A set of an autonomous generator MAG-05.2.XX is used for tracing and determining the depth of non-metallic pipelines, storm channels at a depth of up to 5 meters in conjunction with tracerouting receivers having a "Probe" function with an operating frequency of 512 Hz. The principle of tracing non-metallic pipelines with an autonomous MAG-05 generator.2.XX A small-sized autonomous generator MAG-05 is placed on a problematic section of the highway using a cable pushing device. The generator emits an electromagnetic field. When the receiver is moved on the earth's surface (when the receiver axis is perpendicular to the communication axis), a signal with pronounced two local minima, a general maximum and two false peaks is induced along the communication axis in the receiving coil. When moving the receiver across the axis of the generator, there are no local minima and false peaks of the signal.

Smart submersible reinforced probe L = 150 mm SZPGU.150P with built-in flash memory is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor, Android program installed. Operating conditions of the SZPGU.150P smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the SZPGU.150P smart probe Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor, Android program installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

A trace searching kit for finding underground utilities (cable lines, metal pipelines, and other communications made of conductive materials), as well as the ability to search for places of damage to the external insulation of communications. The kit includes a receiver in the form of a monoblock with a frost-resistant LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line and the most powerful multi-frequency generator in the TECHNO-AC line, with a range of up to 10 km. Connection to the desired route is possible both by contact and contactless method.

Appointment Athlete KAI-1.502 (IDM) • Search for a live cable. • Detection of the passage of hidden communications (metal pipelines, cable lines). • Preliminary detection of the distance to the place of damage. • Search for places of cable damage in an acoustic way. • Search for places of cable damage by electromagnetic means. The presence of the "Friend-Foe" mode.