Primelab

The Tishchenko Primelab flask for flushing gases through liquid has a non-standard design. Two outlets with olives at the ends are soldered into the outer part, which provide a strong connection with the hoses. There is a partition in the middle of the container. It is thanks to this form that the quality of gas purification is improved. The main purpose of the bottle is washing, cleaning and drying gases. The Tishchenko flask was made by the Primelab company from borosilicate glass, which has a fairly long service life even with intensive use.

A dephlegmator with a cooling (heating) jacket with a tap system from Primelab is used in the distillation process to control and regulate temperature. Equipped with connection systems: core 60/46 and coupling 29/32. There are two tubes with olives at the end. Designed for connecting additional equipment such as distillation units. By using a jacketed dephlegmator for heating or cooling, it is possible to positively influence the final product in processes requiring precise thermal control.

The PrimeLab water jet pump is a simple but effective laboratory device for pumping air from an evaporator, reactor and other equipment, as well as creating a vacuum without connecting to an electrical network. For operation, the use of water supply is sufficient. The pump is made of tempered heat-resistant glass, which ensures a long service life in the absence of serious mechanical damage. At the top of the pump there is a tube to which a soft hose is attached. Through it, water enters the water jet pump. There is a drain pipe at the bottom through which the water drains. A device is connected to the side tube in which it is necessary to pump out the air.

Main features and benefits: - The compact and ergonomic design of the mixer body allows it to be used not only in stationary laboratories, but also in mobile mobile stations. - The submersible type device is ideal for a wide range of laboratory work. - Intuitive system for smooth power adjustment via the handle. - Start and stop the device using just one button located on the front panel, providing excellent ease of use. - The built-in temperature sensor automatically turns off the mixer if there is a risk of motor overheating, ensuring safety and reliability in operation. Structure and operation of the device: - The device is made in the form of a compact block made of a plastic case, which makes it light and convenient to use. - On the front panel of the device there is a potentiometer knob with a switch and an LED indicator. - On the back of the case there is a hole with a diameter of 7 mm for installing a bracket and a connector for connecting a power supply. - The lower part of the device is equipped with a three-jaw chuck on a hollow shaft. - The top of the device has a hole for the shaft of the mixing nozzle, which allows you to change the height of the nozzle without moving the device up or down if it is installed on a tripod. - The device also has the function of overload protection and complete shaft locking, which ensures its long service life and protects it from unpleasant situations. Primelab is an innovative and user-friendly overhead drive mixer developed in Russia. Thanks to its technological capabilities and ease of operation, it will become an indispensable tool for achieving high quality and efficient mixing of viscous and dense liquids in various fields of industry and scientific research. Characteristics Device overload protection Eat Max. viscosity of the stirred sample, mPa*s 10,000 Maximum torque, Ncm 45 A country Russia Control type analog Mixer shaft diameter max., mm 0.5-10 Motor type Brushless, DC Speed range, rpm 20-2200 Overall dimensions, L×W×H, mm 182x61x200 Protection class acc. to DIN EN60529 IP44 Sample volume (water) 20 liters Display absent Timer absent Engine power, W 53 Power consumption, W 24 Device weight, kg net/gross, kg 2.0/3.2 Supply voltage, V 200–240 Current frequency, Hz 50 Overheat protection (shutdown) Eat The device is supplied with: 1) device – 1 piece; 2) power supply – 1 pc.; 3) power cable – 1 pc.; 4) instruction manual combined with passport – 1 pc.; 5) bracket Ø10 mm. for attaching the device to a tripod – 1 PC.; 6) hex key 3 mm. - 1 PC.

Vacuum membrane pump PL.HM02.02.10 Primelab is an effective, compact and powerful device for creating a vacuum or pumping gases. It makes virtually no noise, is suitable for constant use, and does not cause discomfort. Overheating protection is provided. All chambers are made of fluoroplastic, connections are coated with fluoroplastic, and valves are made of FFKM, which guarantees maximum safety of the device. Elements and parts of the device do not react with working substances. Device performance depends on the camera connection method: • Independent. Pumping speed – 38 l/min with a maximum of 45 mbar; • Parallel. Pumping speed – 76 l/min at a maximum pressure of 45 mbar; • Consistent. Pumping speed – 38 l/min at a maximum pressure of 10 mbar.

Petri dish PrimeLab 120 mm, glass - a small laboratory container with a small edge around the perimeter, made of tempered glass. Consists of two parts with the following features: • The diameter of the upper part is 129 mm with 120 mm of the lower part. • The height of the upper part is slightly lower than the height of the lower part, due to which the upper “lid” fits freely onto the base to protect the contents from the external environment and other microorganisms. • Glass thickness is 2 mm.

Bourdon vessel, version 2. Made of borosilicate glass.

A variation of the Liebig refrigerator is produced by PrimeLab. Designed for distillation, distillation, condensation and more. It has a standard design consisting of two glass tubes, one of which is located inside the other. Water is poured into the outer tube, and vapor condenses in the inner tube, after which it flows down. The Primelab company accepts orders for the manufacture of laboratory glassware and instruments, including Liebig refrigerators. We use exclusively high-quality borosilicate glass.

The PrimeLab 60mm Petri dish is made of clear tempered glass that can withstand heat sterilization. Designed for reusable use. The cup consists of two parts: a base (60 mm) and a lid (65 mm), which is larger in diameter than the base and slightly smaller in height. The second part is superimposed on the first to protect the contents from the external environment.

Primelab filtration apparatus, 500 ml flask is a laboratory device designed to simplify the filtration procedure in liquid media. Suitable for cleaning collections, filtering liquids and obtaining precipitates during various reactions. The apparatus is equipped with a receiving conical flask with an adapter and side outlet, a filter, a clamp and a 300 ml cylindrical funnel. The volume of the filtrate receiver is 500 ml. All parts of the device are made of durable borosilicate glass, thanks to which it has a long service life.

Conical flask Kn-2-500-50 Primelab is a universal glass vessel used for various laboratory studies and reactions. These include filtration, mixing, storage, heating, cooling and other processes. It has a stable shape in the form of a narrow neck of 50 mm and a wide base of 105 mm. The flask is designed for 500 ml. The total height is 175 mm. Made from reliable and durable borosilicate glass. Thermally and chemically stable.

The electrochemical cell made of borosilicate glass was manufactured in the glassblowing workshop of the PrimeLab company. It has a long service life and is thermal and chemical resistant. Designed for various electrochemical processes. Externally, it has a non-standard shape with three branches, at the ends of which there are olives. Thanks to this, any soft hose can be firmly attached to the cell. Made of borosilicate glass, which is resistant to mechanical stress. Suitable for working in high temperature environments. You can order electrochemical cells made of borosilicate glass from Primelab in any quantity. Production times depend on quantity.