Equipment

It is designed for thermostating samples of natural and drinking water for organoleptic assessment of odor intensity in accordance with GOST R 57164 and for determining the odor of natural and treated wastewater in accordance with RD 52.24.496. A cooling heat exchanger installed in one of the working baths, when connected to a water supply or a flow cooler, allows you to maintain the temperature in this bath +20 ° C while the other working bath has a temperature of +60 ° C, which meets the requirements of GOST R 57164. The volume of the bath is 5 liters Overall dimensions 400x400x350 mm The open part of the bath is 295x145 mm Bath depth 110 mm Weight 12 kg Power consumption 2.5 kW

It is suitable for the distillation of high-boiling substances and for the implementation of high-temperature catalytic reactions. The operating temperature range is +100...+400 °C. The volume of the bath is 5 liters Overall dimensions 270x490x860 mm Weight 50 kg Power consumption 2.5 kW

The gas flow shaper (FGP) is designed to automate the old fleet of chromatographs of the LHM type, model-3700, "Color" series, etc. in terms of setting and regulating the flow and pressure of both the carrier gas and auxiliary gases. The FGP has a flexible structure and provides regulation of gas flows from two to four independent gas flow channels and up to three pressure channels. The gas pressure at the inlet is (0.4 ± 0.04) MPa. The operating flow ranges of the carrier gas are from 3 to 250 ml/min with a discreteness of 1 ml/min. The ability to specify the type of gas (nitrogen, helium, hydrogen, argon, air). The ranges of hydrogen consumption are from 3 to 250 ml/min with a discreteness of 1 ml/min. The air flow ranges from 10 to 750 ml/min with a discreteness of 1 ml/min. Pressure ranges — from 0.001 to 0.40 MPa with a discreteness of 0.0001 MPa. Deviation of the carrier gas flow rate from the average value of ± 1.5% in the flow range from 50 to 100 ml/min and ± 0.5 ml/min in the flow range from 3 to 50 ml/min. The relative deviation of the average steady-state gas flow rate from the set value in the range: from 3 to 100 ml/min. ± 2.5%, but not less than 0.5 ml/min.; from 100 to 200 ml/min. ± 5%; from 200 to 800 ml/min. ± 10%. Electric power supply from a single—phase AC network with voltage from 187 to 242 V, frequency (50 ± 1) Hz, operating mode - continuous. Power consumption, no more than — 30 VA. Overall dimensions of the FGP (width × depth × height), no more than 160 × 370× 210 mm. Weight, not more than — 8 kg.

Pulsed CDL lasers of the KLM-355-P-x series are optimal radiation sources for building control and automation systems, for scientific and medical purposes.

They are designed for carrying out various technological processes at temperatures from 40 to 500 oC, in vacuum up to 1x10−3 mmHg, or in an inert gas of high purity. They are used for drying, light annealing, aging, low and medium tempering in an oxidizing environment, degassing of ferrous and non-ferrous metals (including copper and copper alloys), or any other materials processed under similar conditions. The program setting of heat treatment modes including vacuuming, high purity inert gas intake with repeated vacuuming allows heating in an oxidizing environment with high purity of the surfaces of the processed parts, without scale formation and oxidation.

Design features: Durable ceramic muffle; Semi-open heaters on four sides of the chamber Microprocessor temperature controller; Conveniently located control panel and bright LED display; Automatic shutdown of heating when opening the door; Ease of management and control; LED indicators of heater operation and protection operation; Alarm when the current temperature exceeds the limits of the permissible range; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1300 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to the maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than 200x110x285 mm Overall dimensions, WxHxD, not more than 505x565x655 mm Rated supply voltage, 220 V Rated power, W 3300

It is designed to maintain a set temperature of a liquid coolant circulating both in an internal bath and in external consumers of a closed or open type. Pump for closed or open type thermostating systems. All-metal stamped tub with a volume of 8 liters and a depth of 150 mm. The stability and uniformity of the temperature in the inner bath is not worse than ± 0.1 ° C. The operating temperature range is +20...+200 °C. Bath volume 8 l Overall dimensions 315x330x400 mm The open part of the bath is 120x200 mm Bath depth 150 mm Weight 13 kg Power consumption 2.2 kW

Specifications: 1. The number of flow cells is 1 pc. 2. Reading - double-ended 2x250 nucleotides. 3. Productivity - 7.5 billion nucleotides (15 million reads). 4. The analysis time is no more than 40 hours.

Device indicators: — minimum diameter of a concentric circle, mm — ( 72 ); — maximum diameter of a concentric circle, mm — ( 250 ); — the distance between the circles of the cone, mm — ( 5 ); — height of the sampling cone, mm — ( 60 ); — upper inner diameter of the sampling cone, mm — ( 37 ); — lower inner diameter of the sampling cone, mm — ( 70 ); — measurement error, mm — ( +2.5 ); — overall dimensions of the cone, mm — ( 280x120 ); — the mass of the cone, kg — ( 4 ).

The LOIP LT-411a modification device consists of an immersion thermostat-circulator LOIP LT-400 and a working bath with a flat removable lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +200 with tap water cooling °C Tvods+5 ...+200 Accuracy of temperature maintenance, °C ± 0.01 The error of setting the set temperature, no more than, ° C ± 0.02 Heater power, W 2200 Pump: max. flow rate, l/min 6...12 pressure, 0.4 bar Bath volume, l 11 The working fluid is water, silicone oil. The open part of the bath / depth, mm 165x230/200 Overall dimensions, mm 268x335x400 Weight, kg 11.4

The magnetic particle testing stand has a simple switch between circular and longitudinal magnetization modes, as well as easy movement and fixation of the solenoid and electrical contact for locating the test object in the working area of ​​the stand. Clamping of the controlled part during circular magnetization occurs in one movement. The stand can be installed on a stationary or mobile magnetic particle testing station. For ease of inspection after magnetization, a tray with a removable protective grid is provided. The protective rear wall protects against the spread of spray splashes outside the working area.