UPN‑AT140 NEUTRON RADIATION CALIBRATION UNIT

SFP+ modules are used to organize high-speed duplex channels with data transfer rates up to 10 Gbit/s. WDM SFP+ optical transceivers are designed to organize a duplex communication channel in a single fiber. CWDM SFP+ allows you to organize 10 Gbit/s channels in passive CWDM systems.

Diesel engine oil spectrometric analysis system "EXPRESS-OIL" is designed to analyze engine oils according to GOST 20759 and determine the concentration of wear elements of rubbing diesel parts, contaminants and additives in diesel engine oils during scheduled maintenance and repair of traction rolling stock in locomotive repair depots, as well as electronic accounting and analysis of dynamics data the content of wear elements in engine oils for each locomotive, as well as the determination of the composition of metals and alloys according to GOST, greases (according to CTCH-28/4, CTCHS-53) and other materials.

Designed for: calibration of Russian and foreign satellite ICV remote sensing radiometers.

DPSS lasers of the KLM-455/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes. Technical specifications Radiation output power: up to 120W Radiation wavelength: 455 nm Output diameter of the radiation beam: 1.5 mm Divergence of the radiation beam: 1.3 mrad Instability of radiation power: 5% Type of modulation: TTL or analog Time to enter the mode: 15min Spectral line width: 0.1nm

An oxygen adsorption station for refueling cylinders is a set of special equipment designed for the production and subsequent refueling of oxygen into cylinders or monoblocks obtained from atmospheric air by short—cycle non-heating adsorption. Unlike the installation, the station is equipped with an oil-free booster compressor, which creates the necessary pressure. Put the squeeze on the compressor. Provita's adsorption stations allow producing oxygen with a purity of up to 99.0%. As a rule, the filling of production gas into cylinders is carried out up to a pressure of 150-200 bar. Composition: 1. Air compressor 2. Dehumidifier 3. Main filter block 4. Air receiver 5. Oxygen generator 6. Oxygen receiver 7. Oil-free booster compressor putting the squeeze on 8.Gas filling ramp

A trace searching kit for searching underground utilities (cable lines, metal pipelines, and other communications made of conductive materials). The kit includes a receiver in the form of a monoblock with a large LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line, as well as a compact autonomous generator with an output power of up to 20 watts and a range of up to 3 km. Connection to the desired route is possible both by contact and contactless method.

Detection of SCR in all possible range of its characteristics High reliability Self-monitoring of components Backup power supply Recording and storage of measurement results in the non-volatile memory of the device The possibility of integration with external security systems DRG-AT2331 together with SRK-AT2327, personal computer and software "SARK.NET " allows you to form an alarm system for detecting the occurrence of a self-sustaining chain reaction (SAS SCR).

The purposes of the ETL TECHNOAS 2 laboratory based on Gazelle Next NN are: • – Testing and searching for damage to cable lines up to 10 kV + SNF (cross–linked polyethylene); • - Posititioning of the location and depth of underground utilities (power and signal cables); • – Identifying the nature of the damage and the distance to the damage site without burning the cable insulation; • – Testing of the cable with alternating high voltage; • – Tests of power cables and cable sheaths with cross-linked polyethylene insulation; • – Measurement of insulation resistance of electrical circuits. ETL TECHNOAS 2 laboratory based on Gazelle Next NN consists of following parts standartly: 1. – Color design; 1. – Laboratory compartment; 1. – Partition between compartments; 1. – Windows: rear side-blind, there is a plastic window with a cable coupling in the rear door; 1. – A 10x10 hatch in the lower right corner for cable output; 1. – Finishing of sidewalls and ceiling; 1. – Floor covering: autolinoleum; 1. – On-duty lighting: standard; 1. – Working lighting: fluorescent lamps; 1. – Furniture: main stand, soft seat. Electrical safety system of ETL TECHNOAS 2 laboratory based on Gazelle Next NN incledes following parts: • – MKZ safety control module; • – Locking switches on the doors of the in/out compartment; • – Audible alarm; • – Light alarm; • – Emergency shutdown button; • – Input release with visible contact break. Additional equipment of ETL TECHNOAS 2 laboratory based on Gazelle Next NN includes: • – 12/220 V voltage converter; • – Diesel/gasoline generator (for field operation); • – Laboratory power management system; • – Additional heater; • – Air conditioning.

KLM-A532-15-5 laser modules are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.

Adsorption nitrogen plant is a set of equipment for the production of nitrogen from atmospheric air by short–cycle heat-free adsorption at a pressure of up to 13 bar. The adsorption nitrogen plants of the Provita company allow to produce nitrogen with a purity of up to 99.9999%. The capacity of the plants ranges from several liters per minute to hundreds of cubic meters per hour. The basis of the installations are nitrogen adsorption generators developed and manufactured by our company. A carbon molecular sieve with a developed microporous structure is used as an adsorbent. The gas generator requires dry compressed air with a pressure of at least 6 bar to operate, so the installation includes an air compressor, as well as a dehumidifier and an air receiver (if they are not part of the compressor). The source air must be cleaned of dust and oil, which is carried out by the main filters included in the installation or directly by the nitrogen generator. The nitrogen receiver is used for the accumulation of production gas.

The set is correlational-acoustic, with graphical indication of the communication axis and digital depth of occurrence. Designed for: • – determination of the location of leakages from pipelines by the correlation method; • – tracing underground utilities with the display of the communication axis and digital measurement of the depth of occurrence; • – built-in GPS/GLONASS module for saving coordinates with subsequent mapping of the communication route on the map; • – clarification of leakage sites by acoustic leak detector; • – creation of an information database on the condition of pipelines and the results of pipeline diagnostics; • – diagnostics of shut-off valves.

DPSS lasers of the KLM-593/x series are diode-pumped solid-state lasers of the visible spectral range (593 nm) with collimated continuous radiation of low and high power (depending on the model). The package includes: a laser head, a power supply, a set of connecting wires, a power cable and a device passport. Depending on the tasks, the following options are available for each laser model: the presence of TTL modulation / the presence of analog modulation, power control via the power supply, the presence of a display for the power supply, improved power instability (<3% / <1%), improved temporary power instability (4 h / 8 h), radiation sweep in-line (5...120°), laser head with fiber output (FC/SMA), extended warranty period, custom housing development. These lasers are widely used in medical equipment, for control and automation of technological processes, in scientific research, astronomy, spectroscopy. They are optimal sources of coherent radiation for the construction of systems of alignment and marking devices.

Oil quenching tanks of the tank type are designed for quenching cooling of products heated to the quenching temperature in oil at temperatures up to 90 ° C in stationary conditions. The workspace environment is oil. Oil quenching tank of the tank type BZM 14.17.8/0.9 for quenching cooling of products heated to the quenching temperature in oil in the range from 40oC to 90oC.