Search

The LP-1000 flow water trap is installed on the inlet flange of the diffusion pump and is designed to reduce the flow of working fluid vapors into the pumped volume by condensing them on the cooled elements of the freezing device.

Laboratory for 0.4-10 kV cable lines based on a trailer (ETL-10) includes: 1. Test facility – Maximum rectified voltage up to 70 kV; – Maximum AC voltage of the industrial frequency of 50 Hz to 50 kV. 2. Burning facility – Maximum voltage up to 30 kV; – Maximum current up to 80 A; – Working hours are not limited; – Switching stages is carried out without breaking the arc at the time of switching; – The ability to start working from any stage of burning (when working with low–voltage cables); - Built-in afterburning. 3. High voltage pulse generator • – Output voltage 0...12 kV / 0...24 kV; • – The pulse energy at each stage is 3000 J; • – Built-in IDM for collaboration with the reflectometer. 5. High-voltage cable defects detector • – Determining the location and depth of the cable at a depth of up to 10 m; • – Tracing at a distance of up to 10 km; • – Search for live electrical cables; • – Search for places where the pipeline and cable intersect; • – Determining the places of damage to cable lines; • – Site surveys before excavation; • – Search for places of damage to the external insulation of the cable; • – GPS\GLONASS coordinates recording and mapping of found communications; • – Cable selection from the bundle; • – Search for the place of damage by acoustic method. 6. Autonomous air heater Planar – An autonomous air heater Planar with a capacity of 2 kW or an analog with a 7.5 l fuel tank.

• Designed for: • – detection of depressurization sites of underground pipelines of heat, water, gas, oil supply systems located at a depth of up to 3 m in channel and without channel laying. • – traces of hidden communications (cable lines, pipelines) in passive mode. • – surveys of the excavation area (before opening the route for the presence of cables, pipelines that complicate excavation).

Optical transceivers are in standard SFP metal cases with separate optical input/output for LC type connectors to transmit the signal over two optical fibres

It is intended for taking and storing samples of biological material for the purpose of safe transportation to the laboratory for analysis. It is convenient for taking flushes, including sanitary ones. Non-sterile.

Purpose: provision of connected equipment with constant voltage; conversion of the RS-485 interface to USB (version 01 only) data transmission via the RS-485 interface (version 02 only).

Technical characteristics: NIP, G410 Discreteness, g0,01 External calibration The size of the scale bowl / platform, mm116 The smallest weighing limit, g0.2 The limits of the permissible error during the initial verification, mgot 0.2g to 50 g incl. ±5; sv. 50g to 200g incl. ±10; sv. 200g to 410g incl. ±15 in accordance with GOST OIML R 76-1-2011 Accuracy class according to GOST OIML R 76-1-2011II is high Weight adjustment 200gF2* The time of setting the readings, s, no more than ~ 1 - 1.5 7 years warranty

The NV-800 P is a small wall-mounted table with plumbing fixtures and a superstructure of the NV line. The table top is 70 cm deep. A lamp and two sockets are built into the superstructure. It is designed for standing work: the height of the table top is 85 cm. External dimensions of the table (W×D×H): 760×700×1650 mm. A working surface for your tasks We offer tables with various work surfaces. Table Model: Tabletop NV-800 PLH: Laminate. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. NV-800 PKX: Porcelain tile. It is a practical solution for most chemical, biological, medical laboratories and workshops. You can put on it drying cabinets, baths and other heating devices. NV-800 PSPH: chemically resistant plastic. It is a good choice for training workshops, analytical and medical laboratories. It does not tolerate high temperatures well, heating devices should not be placed on the surface. NV-800 PPX: Polypropylene. It is chemically resistant, being a specialized solution for chemical laboratories that work a lot with concentrated inorganic acids and alkalis. It is not resistant to high temperatures. A comfortable desk for working in the laboratory The superstructure allows you to compactly place the necessary reagents and laboratory utensils next to the workplace. Its depth is 25 cm, and its height is 80 cm. This table has plumbing fixtures: a faucet and a small sink-drain made of polypropylene resistant to aggressive chemicals are built into the countertop. Its diameter is 135 mm and its depth is 110 mm. The working area is illuminated by a fluorescent lamp (included in the package). The switch is located on the left-hand side of the superstructure. There are also two sockets, one of which is grounded. Sockets have the IP20 degree of protection, their maximum load: 1.5 kW. The side laminated panels of the table (chipboard 16 mm thick) are edged with a 2 mm PVC edge, which increases their impact resistance and mechanical strength. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor. Advantages of NV-800 PH tables A budget solution for laboratories that value the reliability and durability of furniture. Suitable for small rooms. The working surface can be selected based on the needs of your laboratory. It is convenient to work while standing: the height of the working surface from the floor is 85 cm. On the shelves you can store accessories for devices on the table, laboratory utensils or reagents. Application of NV-800 PH tables Tables of the NV series are used in laboratories of the widest profile: at food and light industry enterprises, in scientific and educational workshops, in chemistry classrooms, quality control centers, medical organizations and many others.

It is designed to maintain a set temperature of a liquid coolant circulating both in an internal bath and in external closed-type consumers. Feed pump for external closed-type thermostating systems. All-metal stamped tub with a volume of 10 liters and a depth of 200 mm. The stability and uniformity of the temperature in the inner bath is not worse than ± 0.1 ° C. The operating temperature range is +20...+200 °C. The volume of the bath is 10 liters Overall dimensions 400x275x480 mm The open part of the bath is 120x200 mm Bath depth 200 mm Weight 14 kg Power consumption 2.2 kW

It is designed for thermostating samples in glasses, flasks and other laboratory utensils in cases when high accuracy of temperature maintenance is not required and good uniformity of the temperature field in the working volume is not needed. The operating temperature range is Current +5...+200 °C. Two workstations with a diameter of 110 mm with five steel O-rings. Stamped steel tub with a volume of 5 liters and a depth of 110 mm. The volume of the bath is 5 liters Overall dimensions 385x205x310 mm The open part of the bath is 295x145 mm Bath depth 110 mm Weight 7 kg Power consumption 2.5 kW

Designed for use in the Kjeldahl apparatus used to determine nitrogen. Variants: 1-100-14/23 TS 1-100-19/26 TS 1-1000-29/32 TS 1-250-19/26 specifications 9464-019-29508133-2015, TS 1-50-14/23 TS 1-500-29/32 specifications 9464-019-29508133-2015, TS