Search

The SNVS-40/5 vacuum drying cabinet with a volume of 40 liters with manual vacuum adjustment is designed for heat treatment of materials at temperatures up to 500 with air access and in a vacuum controlled by manual valves. Thanks to modern temperature control, it demonstrates excellent performance of heat treatment modes. The measurement system complies with Russian standards and has certificates of entry into the SI State Register. Design for heat treatment in production and clean laboratories. The cabinet can be equipped with a software control device with an automatic timer and a wide selection of additional options.

The GA-400-N nitrogen generator (hereinafter referred to as the generator) is a modification of the GA-400 nitrogen generator and is designed primarily to work with a storage tank (receiver) in which a certain "reserve" of nitrogen can be created. Unlike the GA-400, the GA-400-H generator has a built-in pressure monitoring system for nitrogen accumulated in the receiver, which puts the generator into "standby" mode when the maximum pressure value is reached in the receiver, and restarts the generator when the pressure drops below the minimum value. This work allows you to reduce energy consumption and increase the service life of the compressor feeding the generator. Technical specifications Volume fraction of nitrogen is not less than 99.5% by volume (including impurities of inert gases — argon, neon, helium) Volume fraction of oxygen is not more than 0.5 % vol. Volume fraction of water vapor is not more than 0.002 % vol.(20 ppm) Maximum nitrogen capacity, with nitrogen pressure in the storage tank below 2 ati, is not less than 400 l/hour (6.66 l/min) Nominal inlet air pressure is 6 ati Maximum allowable inlet air pressure is 8 ati Minimum inlet air pressure is 5.5 ati Compressed air consumption, at nominal inlet pressure and maximum flow rate is no more than 3000 l/h (50 l/min) Factory setting of the maximum pressure value in the storage tank is 3.5± 0.2 ati Factory setting of the minimum pressure value in the storage tank is 2.4 ±0.4 ati Power consumption is not more than 100 VA Overall dimensions, (width x depth x height) are not more than 230x580x680 mm; Weight is not more than 35 kg Working conditions: ambient temperature, C°, from +10 to +35 Electric power supply from single-phase AC mains voltage, V, 220± 10% and frequency, Hz, 50 ± 1 Average full service life is at least 6 years The generator for electrical safety meets the requirements of Class 1, type H according to GOST 12.2.025-76

Furniture for laboratory work. Washing table LAB-M MD13 80.60.90 SS Width, mm: 800 Depth, mm: 600 Height, mm: 900 Equipment: The table top is a single module made of SUS 201 stainless steel (analogous to AISI 201). Attention! The product is recommended to be used only for work with non-aggressive substances. For work with various reagents, in addition to mineral acids, it is recommended to use washing tables made of AISI 304 stainless steel. Inner bowl size – 340*400*130 mm The base of the sink table is a support pedestal made of white melamine Facades – laminated MDF of white color with a thickness of 16 mm, dark gray ABS edging Without shelves

Measurement of the activity of hydrogen ions (pH, pH25), EMF and temperature of aqueous media. Laboratory measurements in various industries and national economy. 24-month warranty for deliveries across the Russian Federation Convenience and accuracy of measurement Automatic temperature compensation. Automatic recognition of buffer solutions. Self-diagnosis Non-volatile electronic notebook Ability to record up to 500 measurement groups in named The user of the folder. USB port, software included The ability to create and manage a data archive on a PC. Graphic indicator with backlight Indication of readings in a user-friendly format. Ease of settings.

Design features: Durable ceramic muffle; Closed heaters on four sides of the chamber; Microprocessor temperature controller; Conveniently located control panel and bright LED display; Automatic shutdown of heating when opening the door; Ease of management and control; LED indicators of heater operation and protection operation; Alarm when the current temperature exceeds the limits of the permissible range; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1100 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than 200x110x285 mm Overall dimensions, WxHxD, mm 505x565x655 Rated supply voltage, 220 V Rated power, W 3300

Designed to measure the temperature of various materials by direct contact of the probe with the measuring object The smart air probe L=1000 mm SSV.1000 is designed to measure the temperature of various materials by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the ThermoMonitor. Android program is installed. Operating conditions of the SZV.1000 smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the smart probe SSV.1000 Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor. Android program is installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor, Android program installed. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

Test tubes are used for blood sampling in biochemistry and immunology. During centrifugation, the gel forms a strong barrier for 48 hours between the clot and the serum. The gel tubes must be centrifuged no later than 2 hours after blood collection. Research material............... blood serum Scope of application............................ serum research in biochemistry, immunology Centrifugation.............................. 1500-2000 g - 10 minutes

Designed to measure the temperature in the external circuit of the LOIP LT-200 and LT-400 series thermostats. An external temperature sensor is connected to the temperature control unit and directly monitors the temperature in the external circuit of the thermostat, which significantly increases the accuracy of temperature maintenance. Temperature range, °C from -50 to +250 Cable length, m 1.4

KLM-A532-1-5 laser modules are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.

The cabinet is made of laminated chipboard with a shockproof PVC edge of 2 mm on the facade. The standard version of the NV-400 SHP laboratory cabinet for labware: a glass door and 2 glass shelves on the top level; a door and 2 shelves-inserts of laminated chipboard on the bottom level; metal legs 100 mm high.

The table is 760 mm high with a 900×800 mm countertop made of porcelain stoneware, monolithic ceramics, stainless steel, chipboard or plastic. Designed for sitting work. It can be equipped with various superstructures, sliding and hanging bollards. Overall dimensions 900x800x760 mm

EQUIPMENT rack support racks – aluminum profile painted with powder paint (RAL 1001) top panel with a depth of 190mm – metal painted with powder paint (RAL 1001)