Spectroscopy cells D=16, L=20

Technical specifications Material: S-TIH53 (Ohara) Length, mm: 12 Height, mm: 1.0±0.01 Thickness, mm: 1.9±0.1 Refractive index, mm: 1.823 Optical aperture, mm2: 10.0*0.45 Back focal length, mm: 0.09 Transmission, %: >99.5 Pitch, mm: 0.5 Antireflection coating, nm at one of the wavelengths from the range: 400-1500 Numerical aperture: FA 0.5, SA:0.1 Surface quality at λ = 633 nm: λ/4 Residual deviation at full angle FW1/e2 mrad: <7, <10, <13

Basic properties Low bandwidth losses; A wide barrage strip. Operating conditions Operating temperature range from minus 10 up to 50 ° C; The relative humidity of the air is up to 98% at a temperature of 25 ° C. Technical specifications Waveguide cross section, mm 5.2×2.6 Bandwidth Fh-Fb at the level of -1 dB, GHz 37-45 The barrage band at the level of -30 dB, GHz 50-70 Bandwidth loss, 0.5-1.0 dB

The height of the optical axis of the furnace above the surface of the spectrometer table is 55 mm, the diameter of the samples is up to 21 mm, the length of the furnace in the direction of the optical axis is not more than 70 mm. The sample is installed in a screw-up cassette and is thermally insulated from the external environment by two screens on each side made of mylar and thin aluminum foil or graphlex. The total absorption of 14.4 keV radiation by the screens does not exceed 10-15%. The furnace is attached to the MS-1104Em spectrometer plate with non-falling screws and, if necessary (for example, when using a camera for recording conversion electrons or other equipment), it is easily removed and installed back. The folding mounting of the furnace allows for rapid replacement of samples without waiting for it to cool down, to perform operational calibration of the spectrometer without removing the furnace, and to measure the Mossbauer spectra of absorbers at room temperature outside it in geometry with a moving source or absorber, including in "compressed" geometry and using resonance detectors.

Technical specifications Material: S-TIH53 (Ohara) Length, mm: 15 Height, mm: 6.5 Thickness, mm: 2.81 Refractive index, mm: 1.823 Effective focal length, mm: 14.2 Radius, mm: 11.7 Rear focal length 12.7 mm: ≥99.5 Transmission, % at one of the wavelengths from the range: 400-1500 Antireflection coating, nm: FA: 0.5, SA:0.1 Surface quality at λ = 633 nm: λ/4

Universal multifunctional tilt-and-turn device (swivel arm) for fixing laser modules with a diameter (diagonal) from 12 to 30 mm.

Technical specifications: Azimuth rotation angle from 0° to 360° with a reading of 0.1° The angle of rotation according to the angle of the place from minus 30° to plus 90° with a count of 0.1° The angle of rotation of the polarization plane from minus 95° to plus 95° with a count of 1° The installation height of the axis of the orientation mechanism is from 1.35 to 2.5 m. Note – The maximum height is determined when the rack is installed, the smooth lifting mechanism is fully extended and the legs are fully extended to the stop, extended at an angle of 30° to the axis of the azimuth mechanism. Smooth height adjustment of the axis of the orientation mechanism 0.25 m In terms of strength under climatic and mechanical influences, the rotary support device (OPU) complies with the norms of group 6 GOST 22261-94 Overall dimensions of the OPU - 1687x2500 (shown in the unfolded state at maximum height. The size Ø1687 is the diameter of the circumscribed circle along the vertices of the triangle occupied by the OPU on a horizontal platform) Operating conditions of the OPU: ambient temperature from minus 50 to plus 60 ° C The mass of the OPU is 19.5 kg

The VT-002 vibration transducers are designed to convert the instantaneous value of the vibration acceleration of an object into an ICP signal of the IEEP standard.

Vibration transducers DN-3-M1 are designed to measure vibration by converting mechanical vibrations into electrical signals proportional to the vibration acceleration of an oscillating object. Vibration converters DN-3-M1 are used in conjunction with vibration measuring devices in factory and laboratory conditions.

Technical specifications Material: S-TIH53 (Ohara) Length, mm: 4 Height, mm: 0.5±0.02 Thickness, mm: 0.4±0.01 Refractive index, mm: 1.823 Effective focal length, mm: 0.3 Rear focal length, mm: 0.08 Transmission, %: >99.5 Power within the angle ± 2.2 mrad, %: >92 Antireflection coating, nm at one of the wavelengths from the range: 400-1500 Numerical aperture: 0.7 Surface quality λ = 633, nm: λ/4

These LFS can be used in conjunction with waveguide bandpass filters to increase the suppression of spurious signals and expand the upper band of the barrier. Basic properties Low bandwidth losses; A wide barrage strip. Operating conditions Operating temperature range from minus 10 up to 50 ° C; The relative humidity of the air is up to 98% at a temperature of 25 ° C. Technical specifications Waveguide cross section, mm 5.2×2.6 Bandwidth Fh-Fb at the level of -1 dB, GHz 45-53.6 The barrage band at the level of -30 dB, GHz 60-78 Bandwidth loss, 0.5-1.0 dB

Structurally, waveguide LPF 37-78 GHz are made on metal plates located in the center of the E-plane of the waveguide. These LFS can be used in conjunction with waveguide bandpass filters to increase the suppression of spurious signals and expand the upper band of the barrier. Basic properties Low bandwidth losses; A wide barrage strip. Operating conditions Operating temperature range from minus 10 up to 50 ° C; The relative humidity of the air is up to 98% at a temperature of 25 ° C. Technical specifications Waveguide cross section, mm 3.6×1.8 Bandwidth Fh-Fb at the level of -1 dB, GHz 60-78 The barrier band at the level of -30 dB, GHz 85-120 Bandwidth loss, 0.5-1.2 dB