It is designed for simultaneous polishing of four copper plates measuring 75×12.5×2 mm used in determining the corrosive effect of fuels in accordance with GOST ISO 2160, GOST 32329, GOST 6321, GOST 2917 and ASTM D130.
It is used for determining the low-temperature characteristics of petroleum products and organic chemical products in accordance with the State Standard 20287 (method A), EN 23015, ASTM D97 and GOST 18995.5.
Allows you to install and securely fix up to 6 verifiable thermometers with a diameter of the submerged part from 9 to 16 mm.
The design of the holder eliminates damage to glass thermometers.
It is designed for calibration thermostats THERMOTEST-100 and THERMOTEST-300.
The spring holder for LT 300 or LT electronic thermometers allows you to simply and securely mount the temperature sensor on the walls of laboratory utensils so that it does not touch either its bottom or the wall.
This allows temperature measurements to be carried out not only conveniently, but also correctly.
Allows you to install and securely fix up to 6 verifiable thermometers with a diameter of the submerged part from 3 to 9 mm.
The design of the holder eliminates damage to glass thermometers.
It is designed for calibration thermostats THERMOTEST-100 and THERMOTEST-300.
It is used for determining the turbidity or fluidity temperature of petroleum products in accordance with EN 23015 and ASTM D97.
For testing, additional sets of devices BNTI 05 04 K and BNTI 05 04 3K are required.
A set of devices is used to determine the oil content in oil paraffins in accordance with the State Standard 9090 and is intended for placement in a liquid bath BNTI 05 04.
It is used to determine the corrosive effect of petroleum products on a copper plate in accordance with GOST ISO 2160, GOST 32329, GOST 6321 and GOST 2917.
The holder with flat steel springs allows you to install and securely fix up to 6 verifiable thermometers with a diameter of the submerged part from 3 to 9 mm.
It is designed for calibration thermostats THERMOTEST-100 and THERMOTEST-300.
The holder with flat steel springs allows you to install and securely fix up to 6 verifiable thermometers with a diameter of the submerged part from 3 to 9 mm.
It is designed for THERMOTEST 05 and THERMOTEST-05-1 thermostats.
If you are going to use an electronic thermometer LT 300, LT or LTA not in the laboratory, but in the non-laboratory condiditions, this durable case with a lid will protect the sensor from damage.
The size of the case is determined by the length of of your thermometer.
The stopper holder made of Teflon allows you to mount securely the temperature sensor of LTA electronic thermometers with a diameter of 4 mm in the 14/23-inch laboratory glassware.
It is used for recording transmission spectra of medium–sized and arbitrary-shaped solid samples - polymer films of various thicknesses, optical parts, semiconductor wafers, large crystals, etc.
• Thanks to quick-release nuts, it provides convenient fastening of samples
It is necessary for accurate temperature maintenance in external objects.
The diameter and length of the submerged part are 3 and 240 mm, respectively.
The nominal static characteristic of Pt1000.
The stainless steel stand is designed for installation and storage of pressure gauges MTIf 100, MTIf 160 and MTIf 400 in the process of determining the absolute vapor pressure of volatile crude oil and volatile non-viscous petroleum products.
Overall dimensions 170x95x105 mm
Weight 0.5 kg
It is used for determining the low-temperature characteristics of petroleum products and organic chemical products in accordance with the State Standard 20287 (method A), EN 23015, ASTM D97 and GOST 18995.5.
It is designed to accommodate 26 tubes with a diameter of up to 12 mm when thermostated in the inner bath of a low-temperature liquid thermostat CRYO-VT-12 or CRYO-VT-12-1.
Overall dimensions 130x78x170 mm
Weight 0.2 kg
The ISO-KF connection (DIN 28 403 and ISO 2861) allows quick installation and replacement of components in vacuum systems. The connection consists of two symmetrical ISO-KF flanges (1), a centering ring with an O-ring seal (2) and a quick-release clamp (3). High-vacuum ISO-KF connections can be mounted without using a tool by simply turning the nut of the quick-release clamp.
Allows you to install and securely fix up to 6 verifiable thermometers with a diameter of the submerged part from 9 to 16 mm.
The design of the holder eliminates damage to glass thermometers.
It is designed for calibration thermostats THERMOTEST-100 and THERMOTEST-300.
Designed for immersion of objects in the baths of LOIP LT thermostats and LOIP LB-200 precision thermostatic baths to a predetermined depth. Thermostatable objects are placed on a movable pallet, which can be fixed at any required depth. The device is installed on the casing of thermostats and precision thermostatic baths instead of a hinged lid and is equipped with its own removable lid.
Bath volume, l 12 and 16
Pallet size, mm 260x140
Maximum immersion depth, mm 200
The stand provides convenience when taking measurements, allowing you to set the thermometers at eye level.
Designed for calibration thermostat THERMOTEST-100.
Overall dimensions 400x625x490 mm
The ISO-KF connection (DIN 28 403 and ISO 2861) allows quick installation and replacement of components in vacuum systems. The connection consists of two symmetrical ISO-KF flanges (1), a centering ring with an O-ring seal (2) and a quick-release clamp (3). High-vacuum ISO-KF connections can be mounted without using a tool by simply turning the nut of the quick-release clamp.
The safety valves are conveniently fixed with magnets, and in the working position they can be fixed in the lower part of the case, without interfering with access to the thermometer.