It is intended for placing vessels with samples in the working baths of the BNTI 05 04 bath when determining the low-temperature properties of petroleum products, if appropriate test vessels are available.
Suitable for placing vessels with samples for the State Standard 20287 (Method A), EN 23015 or ASTM D97.

VIS-T-D4 Holder

It is the holder with spring clip for working viscometers of types VPJ 1, VPJ 2, VPJ 4, residence permit, Cannon Fenske Routine, Cannon FenskeOpaque, Ubbelohde, BS/IP/RF.

Termeks

Tomsk

Produced in: Tomsk

It is designed for simultaneous polishing of four copper plates measuring 75×12.5×2 mm used in determining the corrosive effect of fuels in accordance with GOST ISO 2160, GOST 32329, GOST 6321, GOST 2917 and ASTM D130.

Tomsk

Produced in: Tomsk

Set of devices for BNTI-05-04 GOST 9090

A set of devices is used to determine the oil content in oil paraffins in accordance with the State Standard 9090 and is intended for placement in a liquid bath BNTI 05 04.

Tomsk

Produced in: Tomsk

A set of BNTI devices-05-04- K

It is used for determining the low-temperature characteristics of petroleum products and organic chemical products in accordance with the State Standard 20287 (method A), EN 23015, ASTM D97 and GOST 18995.5.

Tomsk

Produced in: Tomsk

Universal holder LA-122

Saint Petersburg

Produced in: Saint Petersburg

A set of devices of the TMP-K

It is used to determine the corrosive effect of petroleum products on a copper plate in accordance with GOST ISO 2160, GOST 32329, GOST 6321 and GOST 2917.

Tomsk

Produced in: Tomsk

Set of devices EN 23015 (ASTM D97)

It is used for determining the turbidity or fluidity temperature of petroleum products in accordance with EN 23015 and ASTM D97. For testing, additional sets of devices BNTI 05 04 K and BNTI 05 04 3K are required.

Tomsk

Produced in: Tomsk

A set of BNTI devices-05-04- 3K

It is used for determining the low-temperature characteristics of petroleum products in accordance with the State Standard 20287 (Method A), EN 23015 and ASTM D97

Tomsk

Produced in: Tomsk

A set of VT-ro-2K devices

It is used in determining the density of petroleum products, resins, plasticizers and other chemical products by hydrometers in stainless steel cylinders with a height of 300 mm and internal diameters of 60.5 and 73 mm.

Tomsk

Produced in: Tomsk

Set of devices the State Standard 5960

It is used in determining the brittleness temperature of polyvinyl chloride plastic by express method in accordance with the State Standard 5960.

Tomsk

Produced in: Tomsk

Holder THERMOTEST-D1-9/16

The holder with flat steel springs allows you to install and securely fix up to 6 verifiable thermometers with a diameter of the submerged part from 9 to 16 mm. It is designed for calibration thermostats THERMOTEST-100 and THERMOTEST-300.

Tomsk

Produced in: Tomsk

The spring holder for LT 300 or LT electronic thermometers allows you to simply and securely mount the temperature sensor on the walls of laboratory utensils so that it does not touch either its bottom or the wall. This allows temperature measurements to be carried out not only conveniently, but also correctly.

Tomsk

Produced in: Tomsk

Set of devices the State Standard 18995.5

It is used in determining the crystallization temperature in accordance with the State Standard 18995.5.

Tomsk

Produced in: Tomsk

VIS-T-D2 Viscometer Holder

It is the holder with a screw clip for reference viscometers. It is designed for use in VIS T 06, VIS T 06 01 and VIS T 11 thermostats

Tomsk

Produced in: Tomsk

If you are going to use an electronic thermometer LT 300, LT or LTA not in the laboratory, but in the non-laboratory condiditions, this durable case with a lid will protect the sensor from damage. The size of the case is determined by the length of of your thermometer.

Tomsk

Produced in: Tomsk

Universal holder LA-121

Saint Petersburg

Produced in: Saint Petersburg

Holder THERMOTEST-D1-3/9

The holder with flat steel springs allows you to install and securely fix up to 6 verifiable thermometers with a diameter of the submerged part from 3 to 9 mm. It is designed for calibration thermostats THERMOTEST-100 and THERMOTEST-300.

Tomsk

Produced in: Tomsk

May be interested in

KF flanges in the assortment

Kazan

Produced in: Kazan

Distilate cooler for the AE-25 distiller

from 8 550 ₽

The distillate cooler is installed directly on the body of the aquadistillator and provides cooling of the finished distillate from 80 ° C to 40 ° C.

Belgorod

Produced in: Belgorod

External temperature sensor PT 1000

from 6 120 ₽

Основные характеристики Диапазон измерения температуры, °С От -70 до + 200 Погрешность измерения температуры, °С, не более 1 Номинальное сопротивление при 25 С,кОм 1.0 Длина рабочей части PT 1000 (погружной) 250 мм Длина ручки 50 мм, диаметр ручки М12 Длина провода до 600 мм

Mytishchi

Produced in: Moscow region, Mytishchi

Quartz cuvette

from 1 700 ₽

Designed for devices of the SF, Minigem, Specord series when operating in the spectral range from 260 to 2500 nm. Chemically resistant to acids (except hydrofluoric acid) and dilute alkalis.

Suponevo

Produced in: Bryansk region

CRYO basket-VT-06-K

It is designed to accommodate thermostatically controlled objects in the inner bath of the liquid low-temperature thermostat CRYO VT 06. The height-adjustable bottom allows objects to be immersed in the coolant to the required depth. Internal dimensions 300x200x120 mm Weight 2.7 kg

Tomsk

Produced in: Tomsk

Tomsk

Produced in: Tomsk

CRYO-W Basket-12-12/ 26K

It is designed to accommodate 26 tubes with a diameter of up to 12 mm when thermostated in the inner bath of a low-temperature liquid thermostat CRYO-VT-12 or CRYO-VT-12-1. Overall dimensions 130x78x170 mm Weight 0.2 kg

Tomsk

Produced in: Tomsk

Replacement O-rings for ISO-F flange connections

Kazan

Produced in: Kazan

The clamp connection (DIN 28 404 and ISO 1609) allows connecting components from DN 63 to DN 630 in any position, on any fixed flange regardless of the location of the bolt holes.

Kazan

Produced in: Kazan

LA-230 cooling heat exchanger

Inner diameter, mm 6 Outer diameter, mm 8

Saint Petersburg

Produced in: Saint Petersburg

Basket VT25-K

It is intended for placement in the inner bath of the liquid thermostat VT25 or VT25-2 forms with samples when testing grouting cements in accordance with the State Standard 26798.2. Ventilation openings are nedeed for better convection of the coolant. Internal dimensions 290x250x140 mm Weight 2.5 kg

Tomsk

Produced in: Tomsk

Discs with high sealing capacity for SVB connections (aluminum) for ISO-F flanges

Kazan

Produced in: Kazan

Tripod for test tubes LA-204

Number of sockets, pcs 27 Hole diameter, mm 22 Immersion depth, mm 200 Overall dimensions (WxDxH), mm 235x80x215

Saint Petersburg

Produced in: Saint Petersburg

Crimp support rings (stainless steel) for sealing rings with high sealing capacity

The ISO-KF connection (DIN 28 403 and ISO 2861) allows quick installation and replacement of components in vacuum systems. The connection consists of two symmetrical ISO-KF flanges (1), a centering ring with an O-ring seal (2) and a quick-release clamp (3). High-vacuum ISO-KF connections can be mounted without using a tool by simply turning the nut of the quick-release clamp.

Kazan

Produced in: Kazan

LTA-KC thermometer case

The safety valves are conveniently fixed with magnets, and in the working position they can be fixed in the lower part of the case, without interfering with access to the thermometer.

Tomsk

Produced in: Tomsk

Set of VT18-K devices

The set of devices is designed to accommodate thermostatically controlled objects in the inner bath of the VT18 or VT18-2 liquid thermostat when they are immersed to a depth of 40 or 70 mm from the bottom of the inner bath. Overall dimensions 350x260x70 mm Weight 2.1 kg

Tomsk

Produced in: Tomsk