Equipment

• Description of the TECHNOAS Housing and Communal Laboratory o – Used for hydrodynamic flushing and emergency cleaning of sewage from sludge, sand, grease, household and industrial waste in sewer pipes. o – Determining the location of underground utilities. o – Search and tracing of metallic and non-metallic pipelines. o – Determination of leakage coordinates by acoustic method in underground pressure steel, cast iron and plastic pipelines of heat and water supply systems, regardless of the depth of their laying, the type of soil, determining the exact location of the pipeline and the depth of its occurrence. o – Search for manholes of wells under a layer of snow, soil, asphalt. o – Analysis of the technical condition of the internal cavities of pipelines with a diameter of 60-2000 mm.

The generator is designed to produce hydrogen of the highest purity used to power analytical instruments (chromatographs, gas analyzers, etc.). Technical specifications Purity of hydrogen in terms of dry gas is about 99.998% The concentration of water vapor at 20 OC and 1atm is not more than 10 ppm In the output pressure stabilization mode The range of the specified output pressure of hydrogen is from 1.5 to 6.1 ati Stability of the output pressure of hydrogen is not worse than ± 0.02 ati Maximum hydrogen capacity reduced to normal conditions is 36 l/h The time of setting the operating mode, with the output turned off is no more than 20 minutes In the performance stabilization mode: The range of the specified hydrogen performance is from 0 to 36 l/h Maximum developed pressure in performance mode is 5.0 ati Volume of distilled water to be poured is 1.0 l Distilled water consumption is not more than 0.06 l/hour Water consumption is 2.4 g/l of hydrogen The average life of a replaceable deionization filter cartridge (at maximum performance and single-shift operation) is at least 0.5 years Average power consumption: in stationary mode is no more than 250 VA maximum (at startup) is no more than 300 VA Overall dimensions of the generator, (width x depth x height) are not more than 230x470x450 mm The mass of the generator is not more than 18 kg Operating conditions: ambient temperature, °C, from +10 to +35 powered by single-phase AC voltage, V, 220 (+10 -15)% and frequency, Hz, 50 +1 The generator for electrical safety meets the requirements of Class 1, type H according to GOST 12.2.025-76

Productivity, thousand tab./hour 160 Number of stations 31 Max. pressing force, tn 10 Number of threads 2 Diameter of tablets, mm 6-25,4 Height of tablets, mm 1.5-9 Matrix filling depth, mm 18 Rotor material Rotor die plate: steel 40x13 Filling hopper capacity, l. 20(30) Stepless rotor speed change The change in the speed of rotation of the feeder is independent Supply voltage 380V, 50Hz Power consumption, kW/hour 4.18 Weight, kg 2200 Dimensions, mm 900x900x1800

Main features and benefits: - The compact and ergonomic design of the mixer body allows it to be used not only in stationary laboratories, but also in mobile mobile stations. - The submersible type device is ideal for a wide range of laboratory work. - Intuitive system for smooth power adjustment via the handle. - Start and stop the device using just one button located on the front panel, providing excellent ease of use. - The built-in temperature sensor automatically turns off the mixer if there is a risk of motor overheating, ensuring safety and reliability in operation. Structure and operation of the device: - The device is made in the form of a compact block made of a plastic case, which makes it light and convenient to use. - On the front panel of the device there is a potentiometer knob with a switch and an LED indicator. - On the back of the case there is a hole with a diameter of 7 mm for installing a bracket and a connector for connecting a power supply. - The lower part of the device is equipped with a three-jaw chuck on a hollow shaft. - The top of the device has a hole for the shaft of the mixing nozzle, which allows you to change the height of the nozzle without moving the device up or down if it is installed on a tripod. - The device also has the function of overload protection and complete shaft locking, which ensures its long service life and protects it from unpleasant situations. Primelab is an innovative and user-friendly overhead drive mixer developed in Russia. Thanks to its technological capabilities and ease of operation, it will become an indispensable tool for achieving high quality and efficient mixing of viscous and dense liquids in various fields of industry and scientific research. Characteristics Device overload protection Eat Max. viscosity of the stirred sample, mPa*s 10,000 Maximum torque, Ncm 45 A country Russia Control type analog Mixer shaft diameter max., mm 0.5-10 Motor type Brushless, DC Speed range, rpm 20-2200 Overall dimensions, L×W×H, mm 182x61x200 Protection class acc. to DIN EN60529 IP44 Sample volume (water) 20 liters Display absent Timer absent Engine power, W 53 Power consumption, W 24 Device weight, kg net/gross, kg 2.0/3.2 Supply voltage, V 200–240 Current frequency, Hz 50 Overheat protection (shutdown) Eat The device is supplied with: 1) device – 1 piece; 2) power supply – 1 pc.; 3) power cable – 1 pc.; 4) instruction manual combined with passport – 1 pc.; 5) bracket Ø10 mm. for attaching the device to a tripod – 1 PC.; 6) hex key 3 mm. - 1 PC.

It is intended for use in higher and secondary educational institutions during laboratory workshops on training specialists in engineering and technical specialties and natural science disciplines. Technical specifications: Upost.- 0.1 mV - 500 V; Uperem.- 1 mV-300 V (40 Hz-20 kHz) Ippost. - 0.1 mkA- 2 A; Iperem. - 1.0 mkA - 2 A (40 Hz-1 kHz) Rpost. - 0.1 Ohm – 20 mOhm Generation of triangles, pilobr., "meander", sinusoid. signal in the frequency range 0.1 Hz – 1 MHz Frequency measurement in the range of 0.1 Hz – 1 MHz The form of the measured signals is sine, pulse Constant voltage: at a current of 1 A - + 5 V at a current of 0.5 A for each channel - ± 12 V Adjustable Uppost. at a current of up to 1 A - 0 – 30 V Dimensions - 170x340x380 mm Power supply – 230 V, 50 Hz, 200 VA - max. Weight – 8.0 kg

Catalytic reforming is used to produce high-octane components of automobile gasoline, flavored concentrate for the production of individual aromatic hydrocarbons, as well as technical water. Isomerization of paraffin hydrocarbons is used to increase the octane number of C5 - C6 oil fractions by converting paraffins of normal structure into their isomers having a higher octane number.oroda. Hydrotreating of distillates is used to improve the quality and stability of light distillates, raw materials of catalytic cracking, as a result of the use of reactions of destructive hydrogenation of organosulfur compounds and hydrogenation of unsaturated hydrocarbons. Catalytic cracking is used to obtain additional amounts of light petroleum products, namely high-octane gasoline and diesel fuel, by decomposition of heavy oil fractions in the presence of a catalyst. Alkylation of isobutane with olefins is used to produce gasoline fractions with high stability and detonation resistance using the reaction of interaction of isobutane with olefins in the presence of a catalyst. Polymerization (oligomerization) of olefins is used to produce low molecular weight polymers (oligomers) of propylene and butylene used as motor fuel or raw materials for petrochemical synthesis. Hydrocracking is used to obtain an additional amount of light petroleum products by catalytic decomposition of heavy raw materials in the presence of hydrogen. Thermal cracking and Visbreaking is used to obtain in the mode of thermal cracking – additional amounts of light petroleum products by thermal decomposition of residues from oil distillation, in the mode of visbreaking – improving the quality of boiler fuel Coking is used to produce petroleum coke and an additional amount of light petroleum products from heavy residues. The raw materials are tar, thermal cracking residue, heavy gas oil. The products are, for example, petroleum coke.

The Meta-chrome digital gas flow meter is designed to maintain a given pressure and the ratio of the amount of gases (in the flow mode) or gas flow (in the intake mode) in vacuum installations with automatic and manual control. technical specifications The number of control channels is 2 (or more on request). The maximum flow rate for each of the channels is 700 cm3/min. The possibility of using gas correction coefficients, the most commonly used gases are listed in the leaker database. The accuracy of maintaining a given proportion of gases is 5%. The accuracy of maintaining the specified gas flow rates is 3%. Input pressures from 1 to 4 atm. Electric power supply from a single—phase AC network with voltage from 187 to 242 V, frequency (50 ± 1) Hz, operating mode - continuous. Power consumption (without a personal computer), no more than — 30 VA. Overall dimensions (width × depth × height), no more than 165×350×215 mm. Weight, not more than 5.5 kg.

DPSS lasers of the KLM-470/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes. Technical specifications Radiation output power: up to 20W Radiation wavelength: 470 nm Output beam diameter: 1.5mm Divergence of the radiation beam: 1.3 mrad Instability of radiation power: 5% Type of modulation: TTL or analog Time to enter the mode: 15min Spectral line width: 0.1nm

The sand bath "PB" I2 with digital control and an increased heating area of 260x510 mm is designed for heat treatment of samples, evaporation and laboratory analysis. Optionally, the product can be equipped with a shutdown timer.