Chassis for MCRC19-14PS2 Media Converters

A media converter is used as a converter that converts one signal transmission medium into another. The data transmission medium means optical and copper cable. The scope of application – FastEthernet and GigabitEthernet protocols, STM-1 and STM-4. Media converters are characterized by a number of parameters, by setting that you can choose the optimal network equipment for solving a specific task. The possibility to control the device; Installation location; Properties of the optical receiver-transmitter; Supported transfer rate.

rated output power - 2.0 kW; maximum output power - 2.8 kW; rated supply voltage - DC 400V; Efficiency (depending on frequency) - 95...98%; operating time in CW mode without cooling at an initial temperature of 25°C - 30...60 sec. size with radiator - 310 x 105 x 70 mm; weight with radiator - 3.6 kg. The module has a built-in autonomous temperature protection and RF transistor current protection. There is an input of external blocking of the RF path, which can be used as an input of amplitude modulation. MAG-1K0.LF modules are used to build all Plasma GK series RF generators with frequencies of 0.35...2.0 MHz.

Main Features: Output voltage indication error, ± 0.3 V Output current indication error, ±0.06 A Instability of the output voltage due to changes in the supply voltage, 0.05% Instability of the output current from a change in the supply voltage, 0.2% Instability of the output voltage when the load current changes, 0.1 % Instability of the output current when the load voltage changes, 5.0 % Output voltage ripple, mV 1.0

A dual-fiber optical transceiver in a GBIC metal case, 1.25 Gb/s, SC connector, hot-swappable

A series of modern intelligent relay protection, automation and alarm units PARMA IED-EP+ is designed for use in networks with a voltage from 6 to 750 kV

XFP (10-Gigabit Small Form Factor Pluggable) is a protocol—independent hot-swappable optical transceiver, usually operating at 850nm, 1310nm or 1550nm wavelengths or wavelengths from the CWDM band at a speed of 10 gigabits per second in SONET/SDH, Fiber Channel, Gigabit Ethernet, 10 Gigabit Ethernet and other applications, including WDM channels.

Optical transceivers are in standard SFP metal cases with separate optical input/output for LC type connectors to transmit the signal over two optical fibres

Mathematical processing of the measurement makes it possible to determine and display on the indicator board the relative systematic change in frequency, the average relative value of the frequency difference, the RMS relative frequency deviation, the RMS relative two-sample frequency deviation.

Optical transceivers are available in 9-pin plastic cases with separate optical input/output for SC (FC) connectors

Optical transceivers are in standard SFP metal case with integrated optical input/output for SC,LC connectors for to transmit the signal over a single optical fiber.

PARMA UACHR 12 is designed to eliminate the shortage of active power in the network by automatically turning off consumers when frequency decreases, followed by automatic re-activation of previously disconnected consumers when frequency is restored, as well as to eliminate the shortage of reactive power in the network by disconnecting consumers when voltage decreases, followed by automatic re-activation of previously disconnected consumers when voltage is restored. PARMA UACHR 12 can perform the functions of dividing automation, be used at power plants and substations of power systems, as well as a device for local emergency automation of 0.4 kV networks as part of an automatic load control system. PARMA UACHR 12 is the first microprocessor-based frequency unloading device in Russia that has received a certificate of compliance with the requirements of the standard of the organization of JSC "SO UES" STO 59012820.29.020.003-2016 "Relay protection and automation. Automatic emergency management of power systems modes. Microprocessor devices for automatic frequency unloading. Norms and requirements" No. NC11.SO.RU.0417.0001 One PARMA UACHR 12 device can replace a typical ACR circuit made on microelectronic or electromechanical relays of the RSG-11 type; RF-1, RF-2 and URCH-ZM

The output optical power of the transmitter is -9~ -5 dBm, the sensitivity of the receiver is -21 dBm.

The software and hardware complex with a set of sensors for physics classrooms is designed to measure physical quantities during demonstration work on various sections of physics, as well as to perform experimental work on physics. The set of units of the measuring system is compatible with a PC, has software with an instruction manual. The sensor kit includes 10 sensors for measuring the following physical quantities: - temperature sensor DTV-1 (measuring range -200C + 1100 S); - air humidity sensor DTV-1 (measuring range 10-100%); - pressure sensor DD-1 (measuring range 0-700 kPa); - acceleration sensor DUIMP-1 (measuring range - 4 – + 4 g); - permanent magnetic field induction sensor DUIMP-1 (- 8 – + 8 Gs); - illumination sensor DSCH-1 (measuring range 1 -60 000 lux); - distance sensor DR-1 (measuring range 0.04 – 4.0 m); - angular velocity sensor DUPUS-1 (remote) (measuring range 0 – 210 0/ c); - rotation angle sensor DUPUS-1 (measuring range ±3600); - flame temperature sensor DTP-1 (measuring range 100 – 11000 S).

Optical transceivers are in standard SFP metal cases with separate optical input/output for LC type connectors to transmit the signal over two optical fibres.