The ZVpP-100 vacuum valve with pneumatic actuator equipped with 100mm conditional passages is designed to overlap vacuum systems in the pressure range from 1x10-6 to 1,07x105 Pa (from 0,75x10-8 to 800 mm Hg).
The ZVpP-100 vacuum pneumatic shutter is manufactured in the climatic version of the UHL placement category 4 (i.e. for moderate and cold climate) according to GOST standard 15150-69. The working environment is air and non–aggressive gases. The temperature of the working environment is from plus 1°C to plus 40°C. The vacuum valve with a pneumatic actuator is not intended for use in fire and explosive hazardous industries.
The ZVpP-100 vacuum pneumatic shutter consists of a mechanism, a housing and a pneumatic actuator. The pneumatic actuator includes a pneumatic cylinder, on the piston of which a permanent magnet is installed to determine its position by means of magnetic position sensors "Closed" and "Open" fixed on the cylinder body and a distributor into which compressed air is supplied through a fitting. The speed of the pneumatic cylinder in particular and the operation of the shutter as a whole are regulated by rotating the pneumatic throttle head, if the pneumatic throttle heads are fully tightened, then the speed of opening and closing the shutter will be maximum. The solenoid, powered by a connector, serves as a distributor control device and is applicable in standard production conditions where the relative humidity of the air is not higher than 75%.

2ZVE-160R Electromechanical vacuum shutter with gearbox

The 2ZVE-160R vacuum shutter with electromechanical drive equipped with 160mm conditional passages is designed to overlap vacuum systems in the range of operating pressures from 1x10-6 to 1.07x105 Pa (0.75x10–8 to 800 mm Hg). The 2ZVE-160R shutter is pendulum-type. The 23VE-160R shutter is manufactured in the climatic version UHL (i.e. for moderate and cold climate) and O (i.e. general) 4 according to GOST standard 15150-69. The working environment is air and non–aggressive gases. It is not intended for use in fire and explosive hazardous industries. The 23VE-160R shutter meets the requirements of technical specifications TU 3648-040-00218526-2003. According to the method of protecting a person from electric shock, the gate belongs to Class I electrical equipment according to GOST 12.2.007.0-75.

Vakuummash

Kazan

Produced in: Kazan

2ZVE-400R Electromechanical vacuum shutter with gearbox

The 2ZVE-400R vacuum shutter with electromechanical drive equipped with 400mm conditional passages is designed to overlap vacuum systems in the range of operating pressures from 1x10-6 to 1.07x105 Pa (0.75x10–8 to 800 mm Hg). The 2ZVE-400R shutter is pendulum-type. The 23VE-400R shutter is manufactured in climatic versions UHL (i.e. for moderate and cold climate) and O (i.e. general) 4 according to GOST standard 15150-69. The working environment is air and non–aggressive gases. It is not intended for use in fire hazardous and explosive industries. The 23VE-400R shutter meets the requirements of technical specifications TU 3648-040-00218526-2003. According to the method of protecting a person from electric shock, it belongs to Class I electrical equipment according to GOST 12.2.007.0-75.

Kazan

Produced in: Kazan

ZVPlE-900 Flat Electric Vacuum Shutter

The ZVPlE-900 shutter consists of a housing with connecting flanges, a shutter mechanism, a lip seal to ensure the tightness of the drive element, cover, and electric drive. The shutter mechanism consists of a carriage, an upper and lower flap, which are pulled together by springs and balls. The carriage moves along the housing guides on bearings. The ZVPlE-900 shutter is opened and closed both by electric drive and manually using a flywheel. To switch to manual control mode, there is a switching device on the electric drive. The manual drive is used to adjust and regulate the shutter. ZVPlE-900 valves are manufactured in climatic versions UHL (i.e. for moderate and cold climate) and O (i.e. general) 4 according to GOST standard 15150-69.

Kazan

Produced in: Kazan

2ZVE-160 Electromechanical Vacuum shutter

The 2ZVE-160 vacuum shutter with electromechanical drive equipped with 160mm conditional passages is designed to overlap vacuum systems in the range of operating pressures from 1x10-6 to 1.07x105 Pa (0.75x10–8 to 800 mm Hg). The 2ZVE-160 shutter is pendulum-type. The 23VE-160 shutter is manufactured in the climatic version UHL (i.e. for moderate and cold climate) and O (i.e. general) 4 according to GOST standard 15150-69. The working environment is air and non–aggressive gases. It is not intended for use in fire and explosive hazardous industries. The 23VE-160 shutter meets the requirements of technical specifications TU 3648-040-00218526-2003. According to the method of protecting a person from electric shock, the gate belongs to Class I electrical equipment according to GOST 12.2.007.0-75.

Kazan

Produced in: Kazan

2ZVE-250R Electromechanical vacuum shutter with gearbox

The 2ZVE-250R vacuum shutter with electromechanical drive equipped with 250mm conditional passages is designed to overlap vacuum systems in the range of operating pressures from 1x10-6 to 1.07x105 Pa (0.75x10–8 to 800 mm Hg). The 2ZVE-250R shutter is pendulum-type. The 23VE-250R shutter is manufactured in the climatic version UHL (i.e. for moderate and cold climate) and O (i.e. general) 4 according to GOST standard 15150-69. The working environment is air and non–aggressive gases. It is not intended for use in fire and explosive hazardous industries. The 23VE-250R shutter meets the requirements of technical specifications TU 3648-040-00218526-2003. According to the method of protecting a person from electric shock, the gate belongs to Class I electrical equipment according to GOST 12.2.007.0-75.

Kazan

Produced in: Kazan

ZVPlE-500 Flat Electric Vacuum Shutter

The ZVPlE-500 shutter consists of a housing with connecting flanges, a shutter mechanism, a lip seal to ensure the tightness of the drive element, cover, and electric drive. The shutter mechanism consists of a carriage, an upper and lower flap, which are pulled together by springs and balls. The carriage moves along the housing guides on bearings. The ZVPlE-500 shutter is opened and closed both by electric drive and manually using a flywheel. To switch to manual control mode, there is a switching device on the electric drive. The manual drive is used to adjust and regulate the shutter. ZVPlE-500 valves are manufactured in climatic versions UHL (i.e. for moderate and cold climate) and O (i.e. general) 4 according to GOST standard 15150-69.

Kazan

Produced in: Kazan

ZVPlE-630 Flat Electric vacuum Shutter

The ZVPlE-630 shutter consists of a housing with connecting flanges, a shutter mechanism, a lip seal to ensure the tightness of the drive element, cover, and electric drive. The shutter mechanism consists of a carriage, an upper and lower flap, which are pulled together by springs and balls. The carriage moves along the housing guides on bearings. The ZVPlE-630 shutter is opened and closed both by electric drive and manually using a flywheel. To switch to manual control mode, there is a switching device on the electric drive. The manual drive is used to adjust and adjust the shutter. ZVPlE-630 valves are manufactured in climatic versions UHL (i.e. for moderate and cold climate) and O (i.e. general) 4 according to GOST standard 15150-69.

Kazan

Produced in: Kazan

2ZVE-630/400R Electromechanical Vacuum shutter with gearbox

The 2ZVE-630/400R vacuum shutter with electromechanical drive equipped with 630 / 400mm conditional passages is designed to overlap vacuum systems in the range of operating pressures from 1x10-6do 1,07x105Pa (0,75x10–8do 800 mm Hg). The 2ZVE-630/400R shutter is pendulum-type. The 23VE-630/400R shutter is manufactured in climatic versions UHL (i.e. for moderate and cold climate) and O (i.e. general) 4 according to GOST standard 15150-69. The working environment is air or non–aggressive gases. It is not intended for use in fire hazardous and explosive industries. The 23VE-630/400R shutter meets the requirements of technical specifications TU 3648-040-00218526-2003. According to the method of protecting a person from electric shock, it belongs to Class I electrical equipment according to GOST 12.2.007.0-75.

Kazan

Produced in: Kazan

2ZVE-100 Electromechanical Vacuum shutter

The 2ZVE-100 vacuum shutter with electromechanical drive equipped with conditional passages of 100 mm is designed to overlap vacuum systems in the range of operating pressures from 1x10-6 to 1.07x105 Pa (0.75 x10–8 to 800 mm Hg). Type of shutter 2ZVE-100 pendulum. The 23VE-100 shutter is manufactured in the climatic version of UHL (i.e. for moderate and cold climate) and O (i.e. general) 4 according to GOST 15150-69. The working environment is air and non–aggressive gases and. It is not intended for use in fire and explosive hazardous industries. The 23VE-100 shutter meets the requirements of technical specifications TU 3648-040-00218526-2003. According to the method of protecting a person from electric shock, the gate belongs to Class I electrical equipment according to GOST 12.2.007.0-75.

Kazan

Produced in: Kazan

May be interested in

Vacuum membrane pump PL.HM01.01.8 Primelab

from 150 000 ₽

1 supp.

The Primelab vacuum diaphragm pump PL.HM01.01.8 has excellent performance - up to 38 l/min at a maximum vacuum of 8 mbar. Suitable for a wide range of industrial and laboratory applications. It is used for working with chemically active substances due to the use of high-quality materials in its design that do not react with toxic reagents. The chambers are made of fluoroplastic, all parts have a fluoroplastic coating. Complies with IP20 protection class. Supplied complete with equipment sufficient for quick assembly and operation of the device. Namely this: vacuum pump, cable, instructions, passport, packaging (vacuum regulator and spare parts are not included in the kit and must be ordered separately).

Mytishchi

Produced in: Mytishchi, Moscow region

HF-140-2 POZIS Pharmaceutical refrigerator

from 25 734 ₽

Total volume, l. 140 The volume of the refrigerator compartment, l. 140 Number of compressors, pcs. 1 Height, mm 910 Depth, mm 610 Width, mm 600 Weight, kg., no more 40 Rated power consumption, W 150 Maximum rated power, W 165 Voltage, 220 V Warranty, years 2 Final report on pre-qualification for compliance with the requirements of Good Practice of the EAEU Distribution: yes Cold storage Auto refrigerator defrosting system Temperature in the refrigerator, °C +2... +15 Accuracy of temperature maintenance ±2°C Thermal card: yes Efficiency and energy consumption Electricity consumption, kWh/day, not more than 0.52 Climate class UHL 4.2 (i.e. for moderate and cold climate) Frequency, Hz 50 Approximate dimensions of the product with packaging Net weight of the product, kg 40 Gross weight of the product, kg 43.5 Volume of packaging, m3 0,397 The length of the package, m 0.65 The width of the package, m 0.63 Height of the package, m 0.97

Зеленодольск

Produced in: Zelenodolsk, Tatarstan

Vacuum chamber electric resistance furnace VS-16-22

Mosrentgen

Produced in: Moscow

Monoblock liquid cooling unit MCHV-5

from 216 640 ₽

Designation MCHV-5 Cooling capacity at Two.water= +15C, Tcond=+45C, Current.cp.=+30C, kW 5 Required pump capacity, m3/h 1,2 Pressure loss in the heat exchanger, kRa 30

Tula

Produced in: Tula

VT12 Liquid thermostat

It is designed to maintain a set temperature of a liquid coolant circulating both in an internal bath and in external closed-type consumers. Feed pump for external closed-type thermostating systems. All-metal stamped tub with a volume of 12 liters and a depth of 150 mm. The stability and uniformity of the temperature in the inner bath is not worse than ± 0.1 ° C. The operating temperature range is +20...+200 °C. Bath volume 12 l Overall dimensions 420x330x430 mm The open part of the bath is 150x260 mm Bath depth 150 mm Weight 14 kg Power consumption 2.2 kW

Tomsk

Produced in: Tomsk

Liquid low-temperature thermostat CRYO-T-05-01

The stability and uniformity of the temperature in the working bath is not worse than ± 0.01 ° C. Bath volume 15 l Overall dimensions 790x500x1180 mm The open part of the bath is 125x190 mm Bath depth 250 mm Weight 119 kg Power consumption 4.2 kW

Tomsk

Produced in: Tomsk

Debinding furnace SNOL-25/2,5-I2VP-D

Designation SNOL-25/2,5-I2VP-D Volume, l 25 Temperature,oS 250 Supply voltage, V 380±15%+N+PE

Tula

Produced in: Tula

Laboratory Drying cabinet SNOL-4.4,4.3,4/2,0 AND-SAT

from 878 840 ₽

The furnace SNOL-4.4,4.3,4/2,0 And-SB is designed to determine the aging of bitumen under the influence of high temperature and air at temperatures up to 200 ° C in accordance with GOST 33140-2014, DIN EN 12607-1, ASTM 2872-12 with forced air convection in stationary conditions. The furnace can be equipped with an air humidity sensor for other types of tests.

Tula

Produced in: Tula

Collection for storage of purified water S-240

from 97 000 ₽

Designed for collecting, storing and distributing purified water obtained by various purification methods, with a capacity of 240 liters and 100% stainless steel, which allowed for a long service life. Dimensions in terms of 690x660 mm Weight 24 kg

Livam

Belgorod

clean water storage system

general laboratory

equipment

Belgorod

Produced in: Belgorod

Liquid low-temperature thermostat CRYO-VIS-T-06-01

Operating temperature range -30...+100 °C Four places for glass viscometers or a basket for determining the pour point of petroleum products. The stability and uniformity of the temperature in the working bath is not worse than ± 0.02 ° C. Bath volume 15 l Overall dimensions 440x710x620 mm The open part of the bath is 140x170 mm Bath depth 320 mm The size of the viewing window is 104x270 mm Weight 56 kg Power consumption 3.5 kW

Tomsk

Produced in: Tomsk

Shaft furnace industrial SSHO-4.8/11

Designation SSO-4.8/11 Power, kW 42 Diameter, mm 400 Height, mm 400

Tula

Produced in: Tula

Circulation thermostat LT-117a

The LOIP LT-117a modification device consists of an immersion thermostat-circulator LOIP LT-100 and a working bath with a flat removable lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +100 with tap water cooling °C Tvods+5 ...+100 Accuracy of temperature maintenance, °C ± 0.1 The error of setting the set temperature, no more than ° C ± 0.2 Heater power, W 1900 Pump: max. flow rate, l/min 7.5 pressure, 0.17 bar Bath volume, l 17 The working fluid is water, water-glycerin mixture. Open part of the bath / depth, mm 360x296/150 Overall dimensions, mm 535x335x370 Weight, kg 13

Saint Petersburg

Produced in: Saint Petersburg

DIGITAL MICROSCOPE

The educational microscope is designed to observe transparent agents in transmitted light in a bright field, when studying natural sciences in schools of 2nd - 3rd stages and other educational institutions, as well as for various studies in laboratory practice.

Feodosia Optical Plant (FOZ)

Feodosia

Produced in: Crimea, Feodosia

Laboratory electric furnace CHO-10

from 153 403 ₽

Designation SNO-10 Volume, l 10 The material of the working chamber is ceramic Heating 4 sides Power consumption, W, max 4500 Minimum operating temperature, 0C 100

Tula

Produced in: Tula

P-400 Flow Vacuum Trap

The LP-400(R) flow-through water trap is installed on the inlet flange of the diffusion pump and is designed to reduce the flow of working fluid vapors into the pumped volume by condensing them on the cooled elements of the freezing device.

Kazan

Produced in: Kazan

LB23-Sh Laboratory bath

It is intended for thermostating samples in glasses, flasks and other laboratory utensils in cases when high accuracy of temperature maintenance is not required and good uniformity of the temperature field in the working volume is not needed. The operating temperature range is Current +5...+200 °C. Two workstations with a diameter of 110 mm with five steel O-rings, tripods and feet with a clip. Stamped steel tub with a volume of 7 liters and a depth of 160 mm. The volume of the bath is 7 liters Overall dimensions 515x360x710 mm The open part of the bath is 295x145 mm Bath depth 160 mm Weight 7.5 kg Power consumption 2.5 kW

Tomsk

Produced in: Tomsk

Muffle furnace LF-9/11-V2

Design features: Special system of air intake and exhaust of combustion products with adjustable thrust; Programmable microprocessor temperature controller; Three programs of ten steps with the ability to set the temperature, heating speed and holding time for each step; Manual heating mode with timer with sound notification and auto-off; Durable ceramic muffle; Closed heaters on four sides of the chamber; Backlit graphic display; Conveniently located control panel; Automatic shutdown of heating when opening the door; Sound and light alarm when the current temperature exceeds the limits of the permissible interval; The door opens up and faces the user with the cold side; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1100 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to the maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than 200x150x290 mm Overall dimensions, WxHxD, not more than 525x1015x620 mm Rated supply voltage, 220 V Rated power, W 5500

Saint Petersburg

Produced in: Saint Petersburg