Tracing generator AG-144.1

The automatic tracing pulse generator AG-114 is designed to create propagating signals (vibrations) in the routes of hidden communications with the active method of tracerouting. The device creates an alternating sinusoidal current in the studied communication (constantly or in short-term parcels) necessary to determine its location. Features of the AG-114 generator The selected output power (5 W at 1...1000 ohms, 10 W at 1...500 ohms, 20 W at 1...250 ohms) is issued automatically. The ability to work on such high load resistances allows you to trace very extensive communications. Low power provides energy saving and small "readjustments" to neighboring objects, high power provides a high range of broadcast and detection. Three generation modes: pulse – the main high-efficiency mode with high intelligibility against interference; continuous – an additional low-cost mode for short-term special measurements; three–frequency mode, which provides the selection of the optimal frequency on a remote receiver without switching the transmitter (generator). Three generation frequencies: 512 Hz, 1024 Hz, 8928 Hz. Lower frequency – less "readjustment" to neighboring objects, higher frequency – higher detection range. Unusually compact (190x140x80 mm), for such a high output power (20 W), the autonomous design is provided by the use of highly efficient technology "CLASS D (BD)" (pulsed output power amplifier with an efficiency of 80%). As a result, one small-sized autonomous battery with a capacity of only 2.2 Ah provides pulse generation for >5 hours at maximum output power (20 watts). It is possible to work with "recharge" from the charger or increase capacity by connecting an external battery to increase the time resource. The control and display system, which contains only 4 large keyboard switches and 2 LEDs with specific signatures and symbols ("intuitive interface") and is not overloaded with unnecessary, for automatic devices, fine-tuning organs and indicators of numerical parameter values, is designed for convenient operation in the field. The device does not require constant supervision, parameter monitoring, frequent operational switching and is designed to work on the principle of "turned on and went to the track". In case of significant changes in the load resistance (communication) during generation, the device is automatically reconfigured ("repeated auto-negotiation").

The AG-107 generator is designed to create alternating current in electrically conductive communications with the electromagnetic method of tracerouting. Features of the AG-107 generator The main distinguishing feature is the small weight and dimensions of the device with high output power. The AG-107 generator has a built-in battery based on light high-capacity lithium-iron phosphate (LiFePO4) cells with low self-discharge, dimensions 216x180x105 mm, weight 1.8 kg and provides the following maximum output parameters: The output power in continuous operation is 30 watts; output power in intermittent operation mode is 60 W; Output voltage 60 V; current 5 A. The AG-107 generator uses a control interface similar to the AG-105 generator. The generator implements: Four sine wave generation frequencies: 512 Hz, 1024 Hz, 8192 Hz and 33 kHz; continuous, pulse and dual-frequency generation modes; built-in transmitting antenna operating at frequencies of 8192 Hz and 33 kHz; the possibility of connecting an external transmitting antenna and induction tongs; built-in "multimeter" displaying, at the operator's choice, the supply voltage or output parameters: current, power, voltage, load resistance; the ability to work from an external battery or from the mains ~ 220 V. The generator can be operated from an external power supply of 10...25 V. The generator is protected from the effects of voltages up to 400 V when connected to the communication and from exceeding the permissible voltage of the external power supply. The degree of protection of the case - case IP65 completely eliminates the penetration of dust and water jets inside when the lid is open.

The automatic tracing pulse generator AG-105 is designed to create propagating signals (vibrations) in the routes of hidden communications with the active method of tracerouting. The device creates an alternating sinusoidal current in the studied communication (constantly or in short-term parcels) necessary to determine its location. The features of the AG-105 generator Extremely high power output and battery life, for a compact battery pack ("Type C" × 8) and such small overall dimensions. Universal power supply allows you to reach an output power of over 20 watts. With autonomous power supply, the "life cycle" depends on the quality of the "type C" batteries used. For example, with an initial output power of 7 watts in continuous generation mode, the "life cycle" is ≈ 5 hours, and with an initial output power of 15 watts in intermittent modulation mode, the "life cycle" is ≈ 25 hours (using standard new "fresh" batteries, for example, "Energizer C"). When using "ultra-high-capacity" batteries (for example, "Duracell ULTRA" or "COSMOS"), the battery life can be increased by 20-30%. When connecting an external "12V" battery (for example, a car), the operating time is determined by the capacity of this battery. When connecting an external mains power supply "15 V", the operating time is not limited. The dimensions of the portable device in the case are 216x180x105 mm, and the weight does not exceed 2 kg. These features are provided by the use of an ultra-efficient unique modification of the circuit technology for building CLASS D power amplifiers. The pulse output amplifier reaches an efficiency of 85%, which is especially important for "energy-consuming" devices with autonomous power supply.

The AG-120TM generator is designed for localization and diagnostics of underground utilities (cables, pipelines). The maximum power of the generator is up to 300 watts (depending on the selected operating mode). The device has no equal in the qualitative indicator of the ratio: power-resource-dimensions-weight. Application of the AG-120TM generator To trace communications by electromagnetic method (cables, metal pipelines) and acoustic method (metal and non-metallic pipelines). To carry out a highly efficient search for cable damage sites. Carry out diagnostics of gas pipelines and determine the places of damage to the insulation of protective coatings. Work with any receiver due to the possibility of selecting any operating frequency in the range of 200-10000 Hz. Features of the AG-120TM generator Increased battery capacity compared to the AG-120T generator. Automatic matching for a given current in the load, instead of the output power, allows you to get the predicted signal level at the input of the search receiver. The multi-frequency (200-10000 Hz) multifunctional device can be equipped with any search receiver using this frequency range. Automatic selection of output power by an “intelligent” power selection program. The built-in “output multimeter” shows the voltage, current, resistance and power in the load. High output current (up to 15 A) makes it possible to work efficiently on “low-resistance” (up to short-circuit) loads (for example, grounded pipelines). High output voltage (220 V auto./330 V with complement. battery) allows you to effectively trace “high-resistance” long-range communications. Multifunctionality: operation without direct connection with a resonant transmitting antenna, inductive pliers, a shock mechanism and an isolation monitoring sensor. Ability to work in rainy weather (on/off; viewing parameters with the lid closed).

The AG-120T generator is designed for localization and diagnostics of underground utilities (cables, pipelines). The maximum power of the generator is from 120 W to 270 W (depending on the selected operating modes). The device has no equal in the qualitative indicator of the ratio: power-resource-dimensions-weight. Application of the AG-120T generator To trace communications by electromagnetic method (cables, metal pipelines) and acoustic method (metal and NON-metallic pipelines). To perform a highly efficient search for cable damage sites. To carry out diagnostics of gas pipelines and determine the places of damage to the insulation of protective coatings. To work with any receiver thanks to the possibility of selecting any operating frequency in the range of 200-10000 Hz. the features of the AG-120T generator Automatic matching for a given current in the load, instead of the output power, allows you to get the predicted signal level at the input of the search receiver. The multi-frequency (200-10000 Hz) multifunctional device can be equipped with any search receiver using this frequency range. Automatic selection of output power by an “intelligent” power selection program. The built-in “output multimeter” shows the voltage, current, resistance and power in the load. High output current (up to 15 A) makes it possible to work efficiently on “low-resistance” (up to short-circuit) loads (for example, grounded pipelines). High output voltage (220 V auto./330 V with complement. battery) allows you to effectively trace “high-resistance” long-range communications. Multifunctionality: operation without direct connection with a resonant transmitting antenna, inductive pliers, a shock mechanism and an isolation monitoring sensor. Ability to work in rainy weather (on/off; viewing parameters with the lid closed).

The automatic tracing pulse generator AG-105 is designed to create propagating signals (vibrations) in the routes of hidden communications with the active method of tracerouting. The device creates an alternating sinusoidal current in the studied communication (constantly or in short-term parcels) necessary to determine its location. The features of the AG-105 generator Extremely high power output and battery life, for a compact battery pack ("Type C" × 8) and such small overall dimensions. Universal power supply allows you to reach an output power of over 20 watts. With autonomous power supply, the "life cycle" depends on the quality of the "type C" batteries used. For example, with an initial output power of 7 watts in continuous generation mode, the "life cycle" is ≈ 5 hours, and with an initial output power of 15 watts in intermittent modulation mode, the "life cycle" is ≈ 25 hours (using standard new "fresh" batteries, for example, "Energizer C"). When using "ultra-high-capacity" batteries (for example, "Duracell ULTRA" or "COSMOS"), the battery life can be increased by 20-30%. When connecting an external "12V" battery (for example, a car), the operating time is determined by the capacity of this battery. When connecting an external mains power supply "15 V", the operating time is not limited. The dimensions of the portable device in the case are 216x180x105 mm, and the weight does not exceed 2 kg. These features are provided by the use of an ultra-efficient unique modification of the circuit technology for building CLASS D power amplifiers. The pulse output amplifier reaches an efficiency of 85%, which is especially important for "energy-consuming" devices with autonomous power supply.

A set of an autonomous generator MAG-05.2.XX is used for tracing and determining the depth of non-metallic pipelines, storm channels at a depth of up to 5 meters in conjunction with tracerouting receivers having a "Probe" function with an operating frequency of 512 Hz. The principle of tracing non-metallic pipelines with an autonomous MAG-05 generator.2.XX A small-sized autonomous generator MAG-05 is placed on a problematic section of the highway using a cable pushing device. The generator emits an electromagnetic field. When the receiver is moved on the earth's surface (when the receiver axis is perpendicular to the communication axis), a signal with pronounced two local minima, a general maximum and two false peaks is induced along the communication axis in the receiving coil. When moving the receiver across the axis of the generator, there are no local minima and false peaks of the signal.