Catalog
Back to search results
Tracing generator AG-114.1
Back to search results
Tracing generator AG-114.1
from
134 400 ₽
from
134 400 ₽
Go to the manufacturer's website
The automatic tracing pulse generator AG-114 is designed to create propagating signals (vibrations) in the routes of hidden communications with the active method of tracerouting. The device creates an alternating sinusoidal current in the studied communication (constantly or in short-term parcels) necessary to determine its location.
Features of the AG-114 generator
The selected output power (5 W at 1...1000 ohms, 10 W at 1...500 ohms, 20 W at 1...250 ohms) is issued automatically. The ability to work on such high load resistances allows you to trace very extensive communications. Low power provides energy saving and small "readjustments" to neighboring objects, high power provides a high range of broadcast and detection.
Three generation modes:
pulse – the main high-efficiency mode with high intelligibility against interference;
continuous – an additional low-cost mode for short-term special measurements;
three–frequency mode, which provides the selection of the optimal frequency on a remote receiver without switching the transmitter (generator).
Three generation frequencies: 512 Hz, 1024 Hz, 8928 Hz. Lower frequency – less "readjustment" to neighboring objects, higher frequency – higher detection range.
Unusually compact (190x140x80 mm), for such a high output power (20 W), the autonomous design is provided by the use of highly efficient technology "CLASS D (BD)" (pulsed output power amplifier with an efficiency of 80%). As a result, one small-sized autonomous battery with a capacity of only 2.2 Ah provides pulse generation for >5 hours at maximum output power (20 watts).
It is possible to work with "recharge" from the charger or increase capacity by connecting an external battery to increase the time resource.
The control and display system, which contains only 4 large keyboard switches and 2 LEDs with specific signatures and symbols ("intuitive interface") and is not overloaded with unnecessary, for automatic devices, fine-tuning organs and indicators of numerical parameter values, is designed for convenient operation in the field. The device does not require constant supervision, parameter monitoring, frequent operational switching and is designed to work on the principle of "turned on and went to the track". In case of significant changes in the load resistance (communication) during generation, the device is automatically reconfigured ("repeated auto-negotiation").
Features of the AG-114 generator
The selected output power (5 W at 1...1000 ohms, 10 W at 1...500 ohms, 20 W at 1...250 ohms) is issued automatically. The ability to work on such high load resistances allows you to trace very extensive communications. Low power provides energy saving and small "readjustments" to neighboring objects, high power provides a high range of broadcast and detection.
Three generation modes:
pulse – the main high-efficiency mode with high intelligibility against interference;
continuous – an additional low-cost mode for short-term special measurements;
three–frequency mode, which provides the selection of the optimal frequency on a remote receiver without switching the transmitter (generator).
Three generation frequencies: 512 Hz, 1024 Hz, 8928 Hz. Lower frequency – less "readjustment" to neighboring objects, higher frequency – higher detection range.
Unusually compact (190x140x80 mm), for such a high output power (20 W), the autonomous design is provided by the use of highly efficient technology "CLASS D (BD)" (pulsed output power amplifier with an efficiency of 80%). As a result, one small-sized autonomous battery with a capacity of only 2.2 Ah provides pulse generation for >5 hours at maximum output power (20 watts).
It is possible to work with "recharge" from the charger or increase capacity by connecting an external battery to increase the time resource.
The control and display system, which contains only 4 large keyboard switches and 2 LEDs with specific signatures and symbols ("intuitive interface") and is not overloaded with unnecessary, for automatic devices, fine-tuning organs and indicators of numerical parameter values, is designed for convenient operation in the field. The device does not require constant supervision, parameter monitoring, frequent operational switching and is designed to work on the principle of "turned on and went to the track". In case of significant changes in the load resistance (communication) during generation, the device is automatically reconfigured ("repeated auto-negotiation").
A set of an autonomous generator MAG-05.2.XX
from
102 000 ₽
A set of an autonomous generator MAG-05.2.XX is used for tracing and determining the depth of non-metallic pipelines, storm channels at a depth of up to 5 meters in conjunction with tracerouting receivers having a "Probe" function with an operating frequency of 512 Hz.
The principle of tracing non-metallic pipelines with an autonomous MAG-05 generator.2.XX
A small-sized autonomous generator MAG-05 is placed on a problematic section of the highway using a cable pushing device. The generator emits an electromagnetic field.
When the receiver is moved on the earth's surface (when the receiver axis is perpendicular to the communication axis), a signal with pronounced two local minima, a general maximum and two false peaks is induced along the communication axis in the receiving coil. When moving the receiver across the axis of the generator, there are no local minima and false peaks of the signal.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Tracing generator AG-120T
from
207 000 ₽
The AG-120T generator is designed for localization and diagnostics of underground utilities (cables, pipelines).
The maximum power of the generator is from 120 W to 270 W (depending on the selected operating modes).
The device has no equal in the qualitative indicator of the ratio: power-resource-dimensions-weight.
Application of the AG-120T generator
To trace communications by electromagnetic method (cables, metal pipelines) and acoustic method (metal and NON-metallic pipelines).
To perform a highly efficient search for cable damage sites.
To carry out diagnostics of gas pipelines and determine the places of damage to the insulation of protective coatings.
To work with any receiver thanks to the possibility of selecting any operating frequency in the range of 200-10000 Hz.
the features of the AG-120T generator
Automatic matching for a given current in the load, instead of the output power, allows you to get the predicted signal level at the input of the search receiver.
The multi-frequency (200-10000 Hz) multifunctional device can be equipped with any search receiver using this frequency range.
Automatic selection of output power by an “intelligent” power selection program.
The built-in “output multimeter” shows the voltage, current, resistance and power in the load.
High output current (up to 15 A) makes it possible to work efficiently on “low-resistance” (up to short-circuit) loads (for example, grounded pipelines).
High output voltage (220 V auto./330 V with complement. battery) allows you to effectively trace “high-resistance” long-range communications.
Multifunctionality: operation without direct connection with a resonant transmitting antenna, inductive pliers, a shock mechanism and an isolation monitoring sensor.
Ability to work in rainy weather (on/off; viewing parameters with the lid closed).
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Tracing generator AG-105
from
87 600 ₽
The automatic tracing pulse generator AG-105 is designed to create propagating signals (vibrations) in the routes of hidden communications with the active method of tracerouting. The device creates an alternating sinusoidal current in the studied communication (constantly or in short-term parcels) necessary to determine its location.
The features of the AG-105 generator
Extremely high power output and battery life, for a compact battery pack ("Type C" × 8) and such small overall dimensions.
Universal power supply allows you to reach an output power of over 20 watts. With autonomous power supply, the "life cycle" depends on the quality of the "type C" batteries used. For example, with an initial output power of 7 watts in continuous generation mode, the "life cycle" is ≈ 5 hours, and with an initial output power of 15 watts in intermittent modulation mode, the "life cycle" is ≈ 25 hours (using standard new "fresh" batteries, for example, "Energizer C"). When using "ultra-high-capacity" batteries (for example, "Duracell ULTRA" or "COSMOS"), the battery life can be increased by 20-30%. When connecting an external "12V" battery (for example, a car), the operating time is determined by the capacity of this battery. When connecting an external mains power supply "15 V", the operating time is not limited.
The dimensions of the portable device in the case are 216x180x105 mm, and the weight does not exceed 2 kg.
These features are provided by the use of an ultra-efficient unique modification of the circuit technology for building CLASS D power amplifiers. The pulse output amplifier reaches an efficiency of 85%, which is especially important for "energy-consuming" devices with autonomous power supply.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Tracing generator AG-105
from
89 400 ₽
The automatic tracing pulse generator AG-105 is designed to create propagating signals (vibrations) in the routes of hidden communications with the active method of tracerouting. The device creates an alternating sinusoidal current in the studied communication (constantly or in short-term parcels) necessary to determine its location.
The features of the AG-105 generator
Extremely high power output and battery life, for a compact battery pack ("Type C" × 8) and such small overall dimensions.
Universal power supply allows you to reach an output power of over 20 watts. With autonomous power supply, the "life cycle" depends on the quality of the "type C" batteries used. For example, with an initial output power of 7 watts in continuous generation mode, the "life cycle" is ≈ 5 hours, and with an initial output power of 15 watts in intermittent modulation mode, the "life cycle" is ≈ 25 hours (using standard new "fresh" batteries, for example, "Energizer C"). When using "ultra-high-capacity" batteries (for example, "Duracell ULTRA" or "COSMOS"), the battery life can be increased by 20-30%. When connecting an external "12V" battery (for example, a car), the operating time is determined by the capacity of this battery. When connecting an external mains power supply "15 V", the operating time is not limited.
The dimensions of the portable device in the case are 216x180x105 mm, and the weight does not exceed 2 kg.
These features are provided by the use of an ultra-efficient unique modification of the circuit technology for building CLASS D power amplifiers. The pulse output amplifier reaches an efficiency of 85%, which is especially important for "energy-consuming" devices with autonomous power supply.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Tracing generator AG-114.1
from
82 200 ₽
The automatic tracer pulse generator "AG-114.1" is designed to create propagating signals (vibrations) in the routes of hidden communications with the active method of tracerouting. The device creates an alternating sinusoidal current in the studied communication (constantly or in short-term parcels) necessary to determine its location.
The features of the AG-114.1 generator
The selected output power (5 W at 1...1000 ohms, 10 W at 1...500 ohms, 20 W at 1...250 ohms) is issued automatically. The ability to work on such high load resistances allows you to trace very extensive communications. Low power provides energy saving and small "readjustments" to neighboring objects, high power provides a high range of broadcast and detection.
Three generation modes:
pulse – the main high-efficiency mode with high intelligibility against the background of interference;
continuous – an additional low-cost mode for short-term special measurements;
three–frequency mode, which provides the selection of the optimal frequency on a remote receiver without switching the transmitter (generator).
Three generation frequencies: 512 Hz, 1024 Hz, 8192 Hz. Lower frequency – less "readjustment" to neighboring objects, higher frequency – higher detection range.
Unusually compact (190x140x80 mm), for such a high output power (20 W), the autonomous design is provided by the use of highly efficient technology "CLASS D (BD)" (pulse output power amplifier with an efficiency of 80%). As a result, one small-sized autonomous battery with a capacity of only 2.2 Ah provides pulse generation for >5 hours at maximum output power (20 watts).
It is possible to work with "recharge" from the charger or increase capacity by connecting an external battery to increase the time resource.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Tracing generator AG-144.1
from
134 400 ₽
The automatic tracing generator AG-144.1 is designed to create propagating signals in the routes of hidden communications with active methods of tracing (electromagnetic and acoustic). The device creates in the studied communication an alternating sinusoidal current necessary to determine its location or sound pulses using a shock mechanism.
Sinusoidal generation (electromagnetic traceroute method)
The selected power levels are issued automatically and are in offline mode: 7.5 W at 0.1...1300 ohms, 15 W at 0.15...660 ohms, 30 W at 0.3...1300 ohms, 60 W at 0.6...660 ohms - CONTINUOUSLY, or 15 W at 0.15...660 ohms, 30 W at 0.3...330 OHMS, 60 Watts at 0.6... 660 ohms, 120 watts at 1.2... 330 ohms - PULSES. When using an additional 12/24 V external battery (for example, a car), an output power of 45 watts at 0.45...2000 ohms, 90 watts at 0.9...1000 ohms CONTINUOUSLY, or 90 watts at 0.9... 1000 ohms, 180 watts at 1.8...500 ohms – PULSES can be achieved. The ability to work on such high load resistances allows you to trace very extensive communications. Low power provides energy saving and small "readjustments" to neighboring objects, high power provides a high range of broadcast and detection.
Three generation modes:
pulse – a highly economical mode with high intelligibility against the background of interference is good for interfacing with analog (mainly single-sensor) receiving systems;
continuous – mode is required for most multi-sensor digital receiving systems;
three–frequency mode, which provides the selection of the optimal frequency on a remote receiver without switching the frequency of the transmitter (generator).
Three generation frequencies: 512 Hz, 1024 Hz, 8192 Hz. Lower frequency means less "readjustment" to neighboring objects and higher broadcast range, higher frequency means higher receiver sensitivity, but greater signal attenuation in "long" communication.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Tracing generator AG-107
from
109 800 ₽
The AG-107 generator is designed to create alternating current in electrically conductive communications with the electromagnetic method of tracerouting.
Features of the AG-107 generator
The main distinguishing feature is the small weight and dimensions of the device with high output power.
The AG-107 generator has a built-in battery based on light high-capacity lithium-iron phosphate (LiFePO4) cells with low self-discharge, dimensions 216x180x105 mm, weight 1.8 kg and provides the following maximum output parameters:
The output power in continuous operation is 30 watts;
output power in intermittent operation mode is 60 W;
Output voltage 60 V;
current 5 A.
The AG-107 generator uses a control interface similar to the AG-105 generator.
The generator implements:
Four sine wave generation frequencies: 512 Hz, 1024 Hz, 8192 Hz and 33 kHz;
continuous, pulse and dual-frequency generation modes;
built-in transmitting antenna operating at frequencies of 8192 Hz and 33 kHz;
the possibility of connecting an external transmitting antenna and induction tongs;
built-in "multimeter" displaying, at the operator's choice, the supply voltage or output parameters: current, power, voltage, load resistance;
the ability to work from an external battery or from the mains ~ 220 V.
The generator can be operated from an external power supply of 10...25 V.
The generator is protected from the effects of voltages up to 400 V when connected to the communication and from exceeding the permissible voltage of the external power supply.
The degree of protection of the case - case IP65 completely eliminates the penetration of dust and water jets inside when the lid is open.
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Tracing generator AG-120TM
from
207 000 ₽
The AG-120TM generator is designed for localization and diagnostics of underground utilities (cables, pipelines).
The maximum power of the generator is up to 300 watts (depending on the selected operating mode).
The device has no equal in the qualitative indicator of the ratio: power-resource-dimensions-weight.
Application of the AG-120TM generator
To trace communications by electromagnetic method (cables, metal pipelines) and acoustic method (metal and non-metallic pipelines).
To carry out a highly efficient search for cable damage sites.
Carry out diagnostics of gas pipelines and determine the places of damage to the insulation of protective coatings.
Work with any receiver due to the possibility of selecting any operating frequency in the range of 200-10000 Hz.
Features of the AG-120TM generator
Increased battery capacity compared to the AG-120T generator.
Automatic matching for a given current in the load, instead of the output power, allows you to get the predicted signal level at the input of the search receiver.
The multi-frequency (200-10000 Hz) multifunctional device can be equipped with any search receiver using this frequency range.
Automatic selection of output power by an “intelligent” power selection program.
The built-in “output multimeter” shows the voltage, current, resistance and power in the load.
High output current (up to 15 A) makes it possible to work efficiently on “low-resistance” (up to short-circuit) loads (for example, grounded pipelines).
High output voltage (220 V auto./330 V with complement. battery) allows you to effectively trace “high-resistance” long-range communications.
Multifunctionality: operation without direct connection with a resonant transmitting antenna, inductive pliers, a shock mechanism and an isolation monitoring sensor.
Ability to work in rainy weather (on/off; viewing parameters with the lid closed).
TEKHNO-AS
Kolomna
Produced in: Kolomna, Moscow region
Trace Searcher Success AG-309.20N
from
161 400 ₽
A trace searching kit for searching underground utilities (cable lines, metal pipelines, and other communications made of conductive materials).
The kit includes a receiver in the form of a monoblock with a large LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line, as well as a compact autonomous generator with an output power of up to 20 watts and a range of up to 3 km.
Connection to the desired route is possible both by contact and contactless method.
TEKHNO-AS
Kolomna
Produced in: Moscow region, Kolomna
G3-137 • Low-frequency signal generator
Supertekhpribor
Mytishchi
Produced in: Mytishchi, Moscow region
High-frequency signal generator G4-233
NNPO im. M.V.Frunze
Nizhny Novgorod
Produced in: Nizhny Novgorod
Mobile laboratory for 0.4-10 kV cable lines based on a trailer (ETL-10)
Laboratory for 0.4-10 kV cable lines based on a trailer (ETL-10) includes:
1. Test facility
– Maximum rectified voltage up to 70 kV;
– Maximum AC voltage of the industrial frequency of 50 Hz to 50 kV.
2. Burning facility
– Maximum voltage up to 30 kV;
– Maximum current up to 80 A;
– Working hours are not limited;
– Switching stages is carried out without breaking the arc at the time of switching;
– The ability to start working from any stage of burning (when working with low–voltage cables);
- Built-in afterburning.
3. High voltage pulse generator
• – Output voltage 0...12 kV / 0...24 kV;
• – The pulse energy at each stage is 3000 J;
• – Built-in IDM for collaboration with the reflectometer.
5. High-voltage cable defects detector
• – Determining the location and depth of the cable at a depth of up to 10 m;
• – Tracing at a distance of up to 10 km;
• – Search for live electrical cables;
• – Search for places where the pipeline and cable intersect;
• – Determining the places of damage to cable lines;
• – Site surveys before excavation;
• – Search for places of damage to the external insulation of the cable;
• – GPS\GLONASS coordinates recording and mapping of found communications;
• – Cable selection from the bundle;
• – Search for the place of damage by acoustic method.
6. Autonomous air heater Planar
– An autonomous air heater Planar with a capacity of 2 kW or an analog with a 7.5 l fuel tank.
TEKHNO-AS
Kolomna
Produced in: Moscow region, Kolomna
Cable detector with the ability to control the quality of insulation Athlete TEK-120GAZ-4N
from
439 800 ₽
Multifunctional trace searching kit for finding underground utilities (cable lines, metal pipelines and other communications made of conductive materials).
The presence of an acoustic sensor and a shock mechanism allows tracing NON-METALLIC pipelines, as well as searching for leaks from pipelines and searching for cable damage sites.
The isolation monitoring sensors DKI-117 and the sensor-detector of communication defects DODK-117 search for places of damage to the external insulation of communication.
The kit includes the most powerful multi-frequency generator with a range of up to 10 km. Connection to the desired route is possible both by contact and contactless method.
TEKHNO-AS
Kolomna
Produced in: Moscow region, Kolomna
Cable Finder Success KBI-309N
from
92 400 ₽
Description of the cable finder Success KBI-309N
• – Traceroute receiver in the form of a monoblock with a large LCD display.
• – The image of the route on the device screen.
• – Automatic calculation and display of the depth of the communication up to 10 m, as well as the current in the line.
Purpose of the cable finder Success KBI-309N
• – Search for live electrical cables.
• – Search and tracing of underground utilities (gas pipelines, pipelines, power and telephone cables).
• – Determination of the occurrence of underground utilities at a depth of up to 10 m.
Features of the AP-019.1 receiver
• – Modern digital traceriscover receiver-monoblock AP-019.1.
• – The image of the route on the device screen.
• – Automatic calculation and display of the depth of communication and current in the line.
• – Several options for displaying information on the receiver indicator: "Route", "Graph", "Graph+", "Minimum maximum", modes "Relative distance to communication" and "2-frequencies" allow the operator to use the device's capabilities as efficiently as possible.
• – Additional functions when connecting external sensors.
• – Wide range of operating frequencies (50(60) / 100(120) / 512 / 1024 / 8192 / 32768 Hz, wide band 40...8000 Hz, radio 8...40 kHz).
• – Menu in two languages (Russian and English).
TEKHNO-AS
Kolomna
Produced in: Moscow region, Kolomna
Trace Searcher Success AG-401
from
115 800 ₽
An affordable kit for searching underground utilities (cable lines, metal pipelines, and other communications made of conductive materials).
The kit is equipped with a compact autonomous generator with an output power of up to 20 watts and a range of up to 3 km. Connection to the desired route is possible both by contact and contactless method.
TEKHNO-AS
Kolomna
Produced in: Moscow region, Kolomna
Cable detector with the ability to control the quality of insulation Athlete AG-319SKIM (frost-resistant)
from
360 000 ₽
A trace searching kit for finding underground utilities (cable lines, metal pipelines, and other communications made of conductive materials), as well as the ability to search for places of damage to the external insulation of communications.
The kit includes a receiver in the form of a monoblock with a frost-resistant LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line and the most powerful multi-frequency generator in the TECHNO-AC line, with a range of up to 10 km.
Connection to the desired route is possible both by contact and contactless method.
TEKHNO-AS
Kolomna
Produced in: Moscow region, Kolomna
High-frequency signal generators G4-211, G4-212
NNPO im. M.V.Frunze
Nizhny Novgorod
Produced in: Nizhny Novgorod
Trace detector for diagnostics of non-metallic and metal pipelines Success TPT-522N
from
315 600 ₽
The device is designed for:
• – determining the location and depth of hidden communications (power and signal cable lines, reinforced fiber-optic lines, pipelines made of electrically conductive materials) at a depth of up to 6 m and a distance of more than 5 km from the generator connection point;
• – tracing of communications in channel and non-channel laying by electromagnetic and acoustic methods;
• – determination of places of damage to cable lines by electromagnetic and acoustic methods;
• – site surveys before excavation;
• – detection of depressurization sites of pipelines at a depth of up to 3 m.
TEKHNO-AS
Kolomna
Produced in: Moscow region, Kolomna
Cable searcher Athlete AG-319N
from
292 800 ₽
A trace searching kit for searching underground utilities (cable lines, metal pipelines, and other communications made of conductive materials).
The kit includes a receiver in the form of a monoblock with a large LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line and the most powerful multi-frequency generator in the TECHNO-AC line, with a range of up to 10 km.
TEKHNO-AS
Kolomna
Produced in: Moscow region, Kolomna
Cable Finder Success KBI-106
from
54 600 ₽
Digital tracer device with LED scale and audio output to the operator's headphones. Extremely easy to use and in a compact, lightweight case. Designed for:
• – search for live electrical cable lines.
• – search for places where the pipeline and cable intersect.
• – determination of the occurrence of underground utilities at a depth of up to 6 m .
Features of the AP-014 receiver
• – Digital traceroute receiver.
• – Additional LED indication of the signal level.
• – Wide range of operating frequencies (50 / 100 / 512 / 1024 / 8192 / 32768 Hz, Wide Band 50...2000 Hz).
• – Frost-resistant, working at temperatures up to -30 ° C.
• – Lightweight, compact housing.
TEKHNO-AS
Kolomna
Produced in: Moscow region, Kolomna
Cable searcher Athlete AG-319M (frost-resistant)
from
294 000 ₽
A trace searching kit for finding underground utilities (cable lines, metal pipelines, and other communications made of conductive materials).
The kit includes a receiver in the form of a monoblock with a frost-resistant LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line and the most powerful multi-frequency generator in the TECHNO-AC line, with a range of up to 10 km.
TEKHNO-AS
Kolomna
Produced in: Moscow region, Kolomna
Mobile laboratory for 0.4-10 kV cable lines (ETL-10)
Laboratory for 0.4-10 kV cable lines (ETL-10) consists of:
1. Test facility
• – Maximum rectified voltage up to 70 kV;
• – Maximum AC voltage of the industrial frequency of 50 Hz to 50 kV.
2. Burning facility
• – Maximum voltage up to 30 kV;
• – Maximum current up to 80 A;
• – Working hours are not limited;
• – Switching of stages is carried out without breaking the arc at the time of switching;
• – The ability to start working from any stage of burning (when working with low-voltage cables);
• – Built-in afterburning.
3. High voltage pulse generator
• – Output voltage 0...12 kV / 0...24 kV;
• – The pulse energy at each stage is 3000 J;
• – Built-in IDM for collaboration with the reflectometer.
4. Reflectometer
– Supports 3 methods of determining the location of damage:
• – By pulse reflectometry;
• – By the method of oscillatory discharge;
• – Pulse-arc method.
5. High-voltage cable defects detector
• – Determining the location and depth of the cable at a depth of up to 10 m;
• – Tracing at a distance of up to 10 km;
• – Search for live electrical cables;
• – Search for places where the pipeline and cable intersect;
• – Determining the places of damage to cable lines;
• – Site surveys before excavation;
• – Search for places of damage to the external insulation of the cable;
• – GPS\GLONASS coordinates recording and mapping of found communications;
• – Cable selection from the bundle;
• – Search for the place of damage by acoustic method.
TEKHNO-AS
Kolomna
Produced in: Moscow region, Kolomna
Leakage detector with the function of diagnosing shut-off valves Success AT-407ND
from
106 800 ₽
The leakage detector with the function of diagnosing shut-off valves "Success AT-407ND" is designed to detect places of depressurization of underground pipelines of heat, water, gas, oil supply systems at a depth of up to 3 m in channel and without channel laying.
The search for damage sites is carried out by the acoustic method.
The kit includes a set of "ADM-227", consisting of a small-sized acoustic sensor with a magnetic base and an extension pin.
The presence of the ADM-227 kit in the leak detector makes it possible to carry out work on leak detection and monitoring the condition of shut-off valves, both on metal and plastic pipes of small diameter.
The leak detector allows you to detect violations of the tightness of the shut-off valves. If the sealing of the shut-off element is violated, the product (liquid or gas) leaks. Characteristic acoustic leakage noises are detected by the high-quality microphone of the sensor kit "ADM-227".
TEKHNO-AS
Kolomna
Produced in: Moscow region, Kolomna
Cable Finder Success KBI-406N
from
71 400 ₽
A digital multifunctional tracer device with a large LCD display and sound output both to the built-in speaker and to the operator's headphones.
Purpose of the cable finder Success KBI-406N
• – Search for live electrical cables.
• – Search for places where the pipeline and cable intersect.
• – Determination of the occurrence of underground utilities at a depth of up to 6 m.
• – Survey of the territory before excavation.
Features of the AP-027 receiver
• – Digital traceroute receiver.
• – Large LCD display with switchable operating modes.
• – Audio signal output both to the built-in speaker and to the operator's headphones.
• – Wide range of operating frequencies (50 / 100 / 512 / 1024 / 8192 / 32768 Hz, Wide Band 50...8600 Hz).
• – Possibility to additionally connect an acoustic sensor (leak detector / flaw detector function).
• – Enclosure protection class IP54.
TEKHNO-AS
Kolomna
Produced in: Moscow region, Kolomna