Cable Finder Success KBI-206

The TECHNOAS substation laboratory consists of: Test facility • – Maximum rectified voltage up to 70 kV to 90 mA. • – Maximum AC voltage of the industrial frequency of 50 Hz to 100 kV to 175 mA. The IDP-10 dielectric loss meter unit is based on the Tangent-2000 meter and includes: • – Power transformer parameter meter. • – Measurement of losses and current XX. • – Measurement of short circuit losses and voltage. • – Determination of the transformation coefficient and the winding connection group. • – Measurement of the resistance of the windings to direct current. • – Formation of the test report. A milliohmmeter Measures DC resistance in inductive and non–inductive circuits in the range of 1 µΩ ÷ 10 kΩ at a current of 10A, as well as makes oscillograms of switching the contactor of a high-speed RPN device.

Laboratory equipment for 0.4-10 kV cable lines and cable lines made of cross-linked polyethylene (ETL-10/SNH) 1. Test facility • – Maximum rectified voltage up to 70 kV; • – Maximum AC voltage of the industrial frequency of 50 Hz to 50 kV. 2. SNCH test facility • – Sinusoidal 0-24 kV peak, symmetrical (error ± 1%); • – Rectangular 0-30 kV peak, symmetrical (error ± 1%); • – Constant 0-30 kV of both polarities (error ± 1%); • – Output current 0-30 mA resolution 1 ma (error ±1%); • – Resistance range 0.1 Mohm -15 Mohm; • – The frequency of the output signal is 0.01-1 Hz in increments of 0.01 Hz, automatic frequency selection. 3. Burning installation • – Maximum voltage up to 30 kV; • – Maximum current up to 80 A; • – Working hours are not limited; • – Switching of stages is carried out without breaking the arc at the time of switching; • – The ability to start working from any stage of burning (when working with low–voltage cables); - Built-in afterburning. 4. High voltage pulse generator • – Output voltage 0...12 kV / 0...24 kV; • – The pulse energy at each stage is 3000 J; • – Built-in IDM for collaboration with the reflectometer. 5. Reflectometer – Supports 3 methods of determining the location of damage: • – By pulse reflectometry; • – By the method of oscillatory discharge; • – Pulse-arc method. 6. High-voltage cable detector • – Determining the location and depth of the cable at a depth of up to 10 m; • – Tracing at a distance of up to 10 km; • – Search for live electrical cables; • – Search for places where the pipeline and cable intersect; • – Determining the places of damage to cable lines; • – Site surveys before excavation; • – Search for places of damage to the external insulation of the cable; • – GPS\GLONASS coordinates recording and mapping of found communications; • – Cable selection from the bundle; • – Search for the place of damage by acoustic method. 7. Autonomous gasoline generator • – Rated power 7.5 kVA.

A trace searching kit for finding underground utilities (cable lines, metal pipelines, and other communications made of conductive materials). The kit includes a receiver in the form of a monoblock with LED indication, as well as a generator with increased power up to 180 watts and a range of up to 5 km. Connection to the desired route is possible both by contact and contactless method.

A trace searching kit for searching underground utilities (cable lines, metal pipelines, and other communications made of conductive materials). The kit includes a receiver in the form of a monoblock with a large LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line, as well as a compact autonomous generator with an output power of up to 20 watts and a range of up to 3 km. Connection to the desired route is possible both by contact and contactless method.

A trace searching kit for searching underground utilities (cable lines, metal pipelines, and other communications made of conductive materials). The kit includes a receiver in the form of a monoblock with a large LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line and the most powerful multi-frequency generator in the TECHNO-AC line, with a range of up to 10 km.

The SML is a stationary object located in the existing production premises of the customer or new buildings built according to the project documentation. The technical basis of the SML is made up of up to ten automated workstations (APM ST) for SI verification (calibration) and up to three workstations (RM ST) for diagnostics, adjustment and repair of SI. The ARM ST includes software that allows you to perform SI verification according to a given algorithm and document the results. All SML equipment is placed on standard basic load-bearing structures (BNC). At present, design documentation has been developed and the production of automated control systems has been mastered for the complete set of SML of almost all types of radio and electrical measuring devices, pressure and vacuum SI, SI geometric quantities and other SI. If necessary, the specialists of JSC "NPF "Techno-yaks" are ready to train specialists (ARM operators). Terms and conditions of financing, development, manufacturing, installation, training of specialists are implemented on the basis of contractual relations with customers

QuattroPlex is the first Russian open multiplex platform for the quantitative and qualitative analysis of biomarkers by immunofluorescence analysis on magnetic beads. The detection technology copies the xMap technology, which allows analysis of several dozen analytes in a minimum volume. QuattroPlex benefits:

• • Multiplexing - diagnostics of up to 50 markers in one sample in one analysis
• • analysis of a wide range of markers (rheumatology, autoimmune diseases, HLA, cytokines, infections)
• • open system - use of any test systems based on magnetic coded microspheres
• • high sensitivity - possibility of qualitative and quantitative analysis
• • design that requires minimal desktop space
• • possibility of use in mobile laboratories.

Specifications:

• • Registered size of microspheres, microns — from 0.5 to 100;
• • 3 fluorescence registration channels;
• • fluorescence excitation wavelengths, nm — from 380 to 850;
• • wavelengths of fluorescence registration, nm — from 450 to 950;
• • detector - CMOS matrix;
• • sample volume, µl — from 30 to 60;
• • number of test samples per load — 1 (in a chip);
• • time for analysis of one sample, sec — 4;
• • Results management and analysis software - QuattroPlex results management and analysis software, compatible with Win/Linux;
• • interfaces for connecting to a laptop/PC — Internet/Wi-Fi;
• • dimensions W×D×H, cm — 20×20×30.

Delivery set:

• • system of multiplex analysis of biomarkers QuattroPlex;
• • starter set of consumables;
• • computer, keyboard, mouse and monitor.

The trace searching kit is designed to accurately determine the location and depth of underground utilities (power and signal cable lines, reinforced fiber-optic lines, pipelines made of electrically conductive materials), troubleshooting cable lines, and also allows you to conduct a survey of the area in the shortest possible time and with great reliability before excavation and to prevent damage to engineering communications. The kit includes a digital multifunctional tracking receiver with a large LCD display and audio output both to the built-in speaker and to the operator's headphones. Compact stand-alone generator with display and built-in induction antenna. The output power of the generator is up to 20 watts and the operating range is up to 3 km. Connection to the desired route is possible both by contact and contactless method.

The trace searching kit is designed to accurately determine the location and depth of underground utilities (power and signal cable lines, reinforced fiber-optic lines, pipelines made of electrically conductive materials), troubleshooting cable lines, and also allows you to conduct a survey of the area in the shortest possible time and with great reliability before excavation and to prevent damage to engineering communications. As part of the kit, the receiver is in the form of a monoblock with a large LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line. The kit is equipped with the latest compact autonomous generator AG-107 with built-in batteries, display and built-in induction antenna, for tracing communication in a contactless way.

The purposes of the ETL TECHNOAS 2 laboratory based on Gazelle Next NN are: • – Testing and searching for damage to cable lines up to 10 kV + SNF (cross–linked polyethylene); • - Posititioning of the location and depth of underground utilities (power and signal cables); • – Identifying the nature of the damage and the distance to the damage site without burning the cable insulation; • – Testing of the cable with alternating high voltage; • – Tests of power cables and cable sheaths with cross-linked polyethylene insulation; • – Measurement of insulation resistance of electrical circuits. ETL TECHNOAS 2 laboratory based on Gazelle Next NN consists of following parts standartly: 1. – Color design; 1. – Laboratory compartment; 1. – Partition between compartments; 1. – Windows: rear side-blind, there is a plastic window with a cable coupling in the rear door; 1. – A 10x10 hatch in the lower right corner for cable output; 1. – Finishing of sidewalls and ceiling; 1. – Floor covering: autolinoleum; 1. – On-duty lighting: standard; 1. – Working lighting: fluorescent lamps; 1. – Furniture: main stand, soft seat. Electrical safety system of ETL TECHNOAS 2 laboratory based on Gazelle Next NN incledes following parts: • – MKZ safety control module; • – Locking switches on the doors of the in/out compartment; • – Audible alarm; • – Light alarm; • – Emergency shutdown button; • – Input release with visible contact break. Additional equipment of ETL TECHNOAS 2 laboratory based on Gazelle Next NN includes: • – 12/220 V voltage converter; • – Diesel/gasoline generator (for field operation); • – Laboratory power management system; • – Additional heater; • – Air conditioning.

The combined laboratory up to 35 kV (ETL-35K) consists of: 1. Test facility • – Maximum rectified voltage up to 70 kV; • – Maximum AC voltage of the industrial frequency of 50 Hz to 100 kV. 2. Insulation parameters meter • – Transformation coefficient; • – No-load losses at low voltage; • – Short circuit resistance; • – Voltage and current; • – Power factor; • – Frequency of the measured voltage (current); • – Phase shift angle between voltage and current; • – Measurement of the active resistance of the windings. 3. Burning facility • – Maximum voltage up to 30 kV; • – Maximum current up to 80 A; • – Working hours are not limited; • – Switching of stages is carried out without breaking the arc at the time of switching; • – The ability to start working from any stage of burning (when working with low-voltage cables); • – Built-in afterburning. 4. High voltage pulse generator • – Output voltage 0...12 kV / 0...24 kV; • – The pulse energy at each stage is 3000 J; • – Built-in IDM for collaboration with the reflectometer. 5. Reflectometer – Supports 3 methods of determining the location of damage: • – By pulse reflectometry; • – By the method of oscillatory discharge; • – Pulse-arc method. 6. High-voltage cable defects detector • – Determining the location and depth of the cable at a depth of up to 10 m; • – Tracing at a distance of up to 10 km; • – Search for live electrical cables; • – Search for places where pipelines and cables intersect; • – Determining the places of damage to cable lines; • – Site surveys before excavation; • – Search for places of damage to the external insulation of the cable; • – GPS\GLONASS coordinates recording and mapping of found communications; • – Cable selection from the bundle; • – Search for the place of damage by acoustic method.

A digital multifunctional tracer device with a large LCD display and sound output both to the built-in speaker and to the operator's headphones. Purpose of the cable finder Success KBI-406N • – Search for live electrical cables. • – Search for places where the pipeline and cable intersect. • – Determination of the occurrence of underground utilities at a depth of up to 6 m. • – Survey of the territory before excavation. Features of the AP-027 receiver • – Digital traceroute receiver. • – Large LCD display with switchable operating modes. • – Audio signal output both to the built-in speaker and to the operator's headphones. • – Wide range of operating frequencies (50 / 100 / 512 / 1024 / 8192 / 32768 Hz, Wide Band 50...8600 Hz). • – Possibility to additionally connect an acoustic sensor (leak detector / flaw detector function). • – Enclosure protection class IP54.

For primary and periodic verification and calibration at the field of operation of the following measuring instruments that are part of automated information and measurement systems for commercial accounting of electrical energy (AIIS KUE) or non-automated metering units: • – Measuring voltage transformers (TN) of accuracy classes 0.2 and less accurate at loads normalized by GOST, and at real loads at the metering unit. • – Measuring current transformers (TT) of accuracy classes 0.2S and less accurate with nominal primary currents of 100...5000 A (including high-voltage transformers for 330 kV lines) at loads standardized by GOST 7746-2001 and at real loads; single-phase and three-phase electric active and reactive energy meters of accuracy classes 0.2S and less accurate. • – Auxiliary SI: ammeters, voltmeters, wattmeters, voltage, current and power converters, accuracy classes 0.2 and less accurate, phase meters, power factor meters of accuracy classes from 0.10 and less accurate. • – Energy frequency meters of accuracy classes from 0.02 and less accurate, used at the electricity metering unit. • – For measuring the load capacity of TN iTT. • – For measuring voltage losses in secondary TN circuits. – For measuring the quality of electrical energy (PCE) in accordance with the requirements of GOST 13109-97.

Laboratory equipment for 0.4-35 kV cable lines (ETL-35) 1. Test facility • – Maximum rectified voltage up to 70 kV; • – Maximum AC voltage of the industrial frequency of 50 Hz to 100 kV. 2. Burning facility • – Maximum voltage up to 30 kV; • – Maximum current up to 80 A; • – Working hours are not limited; • – Switching of stages is carried out without breaking the arc at the time of switching; • – The ability to start working from any stage of burning (when working with low-voltage cables); • – Built-in afterburning. 3. High voltage pulse generator • – Output voltage 0...12 kV / 0...24 kV; • – The pulse energy at each stage is 3000 J; • – Built-in IDM for collaboration with the reflectometer. 4. Reflectometer – Supports 3 methods of determining the location of damage: • – By pulse reflectometry; • – By the method of oscillatory discharge; • – Pulse-arc method. 5. High-voltage cable defects detector • – Determining the location and depth of the cable at a depth of up to 10 m; • – Tracing at a distance of up to 10 km; • – Search for live electrical cables; • – Search for places where the pipeline and cable intersect; • – Determining the places of damage to cable lines; • – Site surveys before excavation; • – Search for places of damage to the external insulation of the cable; • – GPS\GLONASS coordinates recording and mapping of found communications; • – Cable selection from the bundle; • – Search for the place of damage by acoustic method.

An accessible tracer without a display with an audible indication in the operator's headphones. Extremely easy to use and in a compact, lightweight case. Purpose of the cable finder Success KBI-211 • – Search for live electrical cable lines. • – Search for places where the pipeline and cable intersect. • – Determination of the occurrence of underground utilities at a depth of up to 6 m. Features of the AP-004 receiver • – Analog traceroute receiver. • – Audio indication in the operator's headphones, the real sound is 50 Hz. • – Frost-resistant, working at temperatures up to -30 °C. • – Lightweight, compact housing.

Digital tracer device with LED scale and audio output to the operator's headphones. Extremely easy to use and in a compact, lightweight case. Designed for: • – search for live electrical cable lines. • – search for places where the pipeline and cable intersect. • – determination of the occurrence of underground utilities at a depth of up to 6 m . Features of the AP-014 receiver • – Digital traceroute receiver. • – Additional LED indication of the signal level. • – Wide range of operating frequencies (50 / 100 / 512 / 1024 / 8192 / 32768 Hz, Wide Band 50...2000 Hz). • – Frost-resistant, working at temperatures up to -30 ° C. • – Lightweight, compact housing.