Ultrasonic bath WU-09-"Ya-FP"-02

Vacuum resistance furnaces are necessary for heating products before pressure treatment, for sintering, degassing, quenching, annealing, soldering and chemical-technological processes. Such furnaces among all the variety of thermal equipment are considered the most environmentally friendly – heat treatment is carried out at t up to +2500 ° C in a purified vacuum. Under certain conditions, vacuum furnaces are used to work with neutral gases. The outer part of the furnace is made of stainless steel and is cooled by liquid. The inner part of the working chamber, where the heat treatment of materials is carried out, is made of an alloy of molybdenum and tungsten. The components are characterized by a low inertia force, reduced gas separation. The settings are available on the control panel, where the instruments, automatic and manual control switches are located. At every enterprise of the electronic industry, nuclear power, an explosion-proof vacuum resistance furnace is needed. The same applies to areas where various products undergo heat treatment at the stage of production and preparation for use.

The operation of the NVDM-250 diffusion pump is based on the capture and transfer of the pumped gas by a steam jet flowing from the slit gaps of the steam line nozzles towards the outlet flange. The oil reflector of the NVDM-250 diffusion pump is a flange with a cooling tube passing through it, soldered to a cap located in the center of the flange. The NVDM-250 open-type diffusion pump heater is a metal housing with a ceramic base laid in it with a heating element in the form of a spiral made of nichrome wire. During the operation of the pump, it is necessary to monitor the flow rate and temperature of the cooling water, the level of the working fluid and its temperature. Replacement or refilling of the working fluid depends on the operating mode of the pump (inlet pressure, pumping duration, etc.) and the composition of the pumped medium. Therefore, the time after which the working fluid is replaced or refilled can be from 100 to 1000 or more hours. A large flow rate of the working fluid is observed when the pump is operating in the range of inlet pressures from 6.6 × 10-2 to 13.3 Pa (from 5 ×10-4 to 1 ×10-1 mmHg). Water at the inlet to the cooling systems of the housing and oil reflector must be supplied with a pressure of no more than 0.5 MPa (5 kgf / cm2) and temperature from plus 4°C to plus 25°C. The recommended cooling water consumption is 100+15 l/h and is regulated by the outlet water temperature, which should not exceed plus 400C. The water drain should be free (with a jet break). Not allowed: operation of the pump without water cooling, exceeding the maximum exhaust pressure of 33.3 Pa (0.25 mmHg) The level of the working fluid during operation, at which the parameters of the pump NVDM-250 are provided, must correspond to min 8mm, max 13mm. The volume of the filled working fluid is 0.55 l

Explosion-proof drying cabinet SNOL-25 is designed for drying, tempering, aging, thermal testing and other types of heat treatment of various materials in an air environment at temperatures up to 240 ° C with natural or forced air convection in stationary conditions. The environment is a potentially explosive mixture of air and gases, vapors, mists of categories IIA and IIB.

Design features: Durable ceramic muffle; Closed heaters on four sides of the chamber; Microprocessor temperature controller; Conveniently located control panel and bright LED display; Ease of management and control; LED indicators of heater operation and protection operation; Automatic shutdown of heating when opening the door; The door opens up and faces the user with the cold side; Alarm when the current temperature exceeds the limits of the permissible range; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1100 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than 200x150x290 mm Overall dimensions, WxHxD, not more than 525x625x620 mm Rated supply voltage, 220 V Rated power, W 5500

Technical characteristics: NIP, G210 Discreteness, g0,001 Calibration,self-calibration The size of the scale bowl / platform, mm116 The smallest weighing limit, g0.02 The price of the verification scale division, mg10 The limits of the permissible error during the initial verification, mgot 0.02g to 50 g incl. ±5; sv. 50g to 200g on ±10; sv. 200g to 210g on ±15 according to GOST OIML R 76-1-2011 Accuracy class according to GOST OIML R 76-1-2011II is high The adjustment weight is built-in The time of setting the readings, s, no more than ~3 7 years warranty

Technical characteristics: NIP, G1100 Discreteness, g0.05/(0.02)* Internal calibration The size of the scale bowl / platform, mm175 x 145 The smallest weighing limit, g2.5 Limits of permissible error during primary verification, mgot 2.5g to 500g incl. ±50; sv. 500g to 1100g incl. ±100 according to GOST OIML R 76-1-2011 Accuracy class according to GOST OIML R 76-1-2011II is high The weight adjustment is built-in The time of setting the readings, s, no more than ~ 1 - 1.5 7 years warranty

Designation SSO-6.6/11 Power, kW 45 Diameter, mm 600 Height, mm 600

a massive copper mold was used in the furnace, as well as a printed crucible made of stabilized (calcium oxide) zirconium dioxide. The furnace has been working for several years at one of the non-ferrous metallurgy enterprises in the production of platinum ingots according to GOST

The power of the built-in electric heaters is 12 kW, there is also an independent emergency shutdown channel. The operating temperature range is +50...+200 °C. The volume of the bath is 30 liters Overall dimensions 500x840x880 mm Weight 60 kg Power consumption 13 kW (three-phase network)

Designation SSO-4.8/11 Power, kW 42 Diameter, mm 400 Height, mm 400

Total volume, l. 280 The volume of the refrigerator compartment, l. 140 Number of compressors, pcs. 2 Height, mm 1683 Depth without handle, mm 610 Depth with handle, mm 650 Width, mm 600 Weight, kg., no more than 84.5 The weight of the refrigerator with glass doors of the upper and lower chambers, kg 84,5 The weight of the refrigerator with a glass door of the upper chamber and a metal door of the lower chamber, kg 79.5 The weight of the refrigerator with metal doors of the upper and lower chambers, kg 74,5 Rated power consumption, W 300 Rated power consumption of the upper refrigerating chamber, W 150 Rated power consumption of the lower refrigerating chamber, W 150 Maximum rated power of the upper refrigerating chamber, W 165 Maximum rated power of the lower refrigerating chamber, W 165 Voltage, 220 V Warranty, years 2 Final report on pre-qualification for compliance with the requirements of Good Practice of the EAEU Distribution availability Cold storage Temperature in the refrigerator, °C from +2 to +15 Accuracy of temperature maintenance ±2°C Thermal card: yes Efficiency and energy consumption Electricity consumption, kWh/day, no more than 1.42 Climate class UHL 4.2 (i.e. for moderate and cold climate) Frequency, Hz Frequency, Hz 50 Approximate dimensions of the product with packaging Net weight, kg 74.5-84.5 Gross weight, kg 80-90 Volume of packaging, m3 0,708 The length of the package, m 0.65 The width of the package, m 0.63 Height of the package, m 1.73

Industrial drying cabinet SNOL (SHS) 200/3-I2 V is designed for drying, tempering, aging, thermal testing and other types of heat treatment of various materials in an air environment at temperatures up to 350 (optionally up to 500) ° C with forced air convection in stationary conditions.

The LOIP LT-408 modification device consists of an immersion thermostat-circulator LOIP LT-400 and a working bath with a small window, which determines the use of LOIP LT-408 mainly for thermostating external systems. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +200 with tap water cooling °C Tvods+5 ...+200 Accuracy of temperature maintenance, °C ± 0.01 The error of setting the set temperature, no more than, ° C ± 0.02 Heater power, W 2200 Pump: max. flow rate, l/min 6...12 pressure, 0.4 bar Bath volume, l 8 The working fluid is water, silicone oil. The open part of the bath / depth, mm dia. 64/200 Overall dimensions, mm 180x335x400 Weight, kg 8,7

A vacuum condenser type trap with a capacity of 2 liters is designed to condense vapors of non-aggressive gases on the internal cooled surfaces of the trap, in order to prevent them from entering the pump.

Operating temperature range 0...+100 °C. Bath volume 18 l Overall dimensions 450x700x640 mm The open part of the bath is 165x165 mm Bath depth 300 mm Weight 47 kg Power consumption 3.5 kW

Productivity, thousand tab./hour 209 Number of stations 41 Max. pressing force, tn 10 Number of threads 2 Diameter of tablets, mm 6-20 Height of tablets, mm 1.5-9 Matrix filling depth, mm 18 Rotor material steel 40x13 Filling hopper capacity, l 20(30) Stepless rotor speed change The change in the speed of rotation of the feeder is independent Supply voltage 380V, 50Hz Power consumption, kW/hour 5.78 Weight, kg 2400 Dimensions, mm 900x900x1800

Designation SNO-17 Volume, l 17 Material of the working chamber ceramics Heating 4 sides Power consumption, W, max 5000 Minimum operating temperature, 0C 100