Water Bi-distiller BWD-3500F

It is intended for obtaining in laboratory conditions from distilled especially pure (deionized) water used for the preparation of solutions, chromatographic samples, refueling of electrolytic hydrogen/oxygen generators and other purposes. Technical specifications The specific conductivity of the resulting water is not more than 0.20* mkSxcm Capacity is at least 6* l/h Metal ion content is not more than: Fe, Pb, Ni, Co 5*mcG/l Zn, Cd, Cu, Mn 1*mcG/l The optical density of ammonia relative to bidistilled water is no more than D - 0.01* Operating time of the replaceable cassette (total volume of purified water) is not less than 700 liters. Volume of refueled distilled water is 1 l Overall dimensions are 440x200x430 mm The mass of the refilled device is not more than 9.5 kg Working conditions: ambient temperature from +10°C to +35°C Power supply from single-phase AC 220 V., 50 Hz The power consumption is not more than 20 VA.

Design features: Special system of air intake and exhaust of combustion products with adjustable thrust; Programmable microprocessor temperature controller; Three programs of ten steps with the ability to set the temperature, heating speed and holding time for each step; Manual heating mode with timer with sound notification and auto-off; Durable ceramic muffle; Semi-open heaters on four sides of the chamber; Backlit graphic display; Conveniently located control panel; Automatic shutdown of heating when opening the door; Sound and light alarm when the current temperature exceeds the limits of the permissible interval; The door opens up and faces the user with the cold side; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1300 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than 200x150x290 mm Overall dimensions, WxHxD, not more than 525x1015x620 mm Rated supply voltage, 220 V Rated power, W 5500

Measurement of electrical conductivity (UEP, UEP25), equivalent salinity and temperature of water and aqueous solutions, including deionized and "ultrapure". Operational control of water-chemical regimes at thermal power facilities. Control of electrical conductivity of water for laboratory analysis of 1, 2 degrees of purity according to GOST 52501-2005. 24-month warranty for deliveries across the Russian Federation Double automatic temperature compensation (ATC) Allows high-precision measurements of the conductivity of "ultrapure" water Selection of the coefficient of thermal compensation at the request of the User Stainless steel flow-immersion sensor Does not require calibration. The sensor design ensures the stability of the permanent cell Electronic notebook Ability to record up to 500 measurement groups in User-named folders Self-diagnosis Ion exchange column with sample current switch IP65 The compact sealed device is reliably protected from dust and moisture USB port, software included Graphic indicator with backlight Low power consumption Up to 600 hours of continuous operation from a set of AA type elements

Purpose: obtaining distilled water of 3 types according to GOST R 58144-2018 "Distilled water", FS.2.2.0020.18 "Purified water" Capacity: 140.0 (-10%) l/h Heating elements: electrodes The quality of the produced water GOST R 58144-2018 "Distilled water", FS.2.2.0020.18 "Purified water" Type of current, frequency, voltage: alternating three-phase, 50 Hz, 380 V Power consumption: 84.0 kW Overall dimensions (L×W×C), mm: 810×630×1420 Weight: 87 kg Warranty period: 12 months from the date of sale Registration certificate for a medical device No. FSR 2008/03707 dated December 05 , 2008 Electrical conductivity of the produced water: 3-4.5 microns/cm Produced water temperature: 50 °C Source water flow rate (at 10 °C water temperature): 1000 (+-10%) l/h Source water pressure: 01,-0.4 MPa Overall dimensions of the control unit (L×W×C), mm: 400×220×500 Execution: outdoor Coefficient of water purification from radionuclides: at least 4000 Service life: at least 8 years

The operation of the NVDM-100 diffusion pump is based on the capture and transfer of the pumped gas by a steam jet flowing from the slit gaps of the steam line nozzles towards the outlet flange. The oil reflector of the NVDM-100 diffusion pump is a cap with a cooling tube soldered onto it with fittings. The open heater of the NVDM-100 diffusion pump is a metal housing with a ceramic base laid in it with a heating element made in the form of a spiral of nichrome wire. During the operation of the pump, it is necessary to monitor the flow rate and temperature of the cooling water, the level of the working fluid and its temperature. Replacement or refilling of the working fluid depends on the operating mode of the pump (inlet pressure, pumping duration, etc.) and the composition of the pumped medium. Therefore, the time after which the working fluid is replaced or refilled can be from 100 to 1000 or more hours. A large flow rate of the working fluid is observed when the pump is operating in the range of inlet pressures from 6.6×10-2 to 13.3 Pa (from 5×10-4 to 1×10-1 mm Hg). Water at the inlet to the cooling systems of the housing and oil reflector should be supplied with a pressure of no more than 0.5 MPa (5 kgf / cm2) and temperature from plus 4˚C to plus 25˚C. The recommended cooling water consumption is 35+5 l/h and is regulated by the outlet water temperature, which should not exceed plus 40˚C. The water drain should be free (with a jet break). Not allowed: operation of the pump without water cooling, exceeding the maximum exhaust pressure of 35 Pa (0.263 mm Hg). The level of the working fluid during operation, at which the parameters of the NVDM-100 diffusion pump are provided, must correspond to min 7mm, max 11mm. The volume of the filled working fluid is 0.07/

It is designed for thermostating samples in glasses, flasks and other laboratory utensils in cases where high accuracy of temperature maintenance is not required and good uniformity of the temperature field in the working volume is not needed. The operating temperature range is Current +5...+200 °C. Four workstations with a diameter of 110 mm with five steel O-rings. Stamped steel tub with a volume of 16 liters and a depth of 160 mm. Bath volume 16 l Overall dimensions 385x370x365 mm The open part of the bath is 325x290 mm Bath depth 160 mm Weight 12 kg Power consumption 2.5 kW

The operating temperature range is +20...+100 °C. Two workplaces for placing prepared Raid bombs with pressure gauges. The stability and uniformity of the temperature in the working bath is not worse than ± 0.01 ° C. The volume of the bath is 30 liters Overall dimensions 335x280x800 mm The open part of the bath is 120x210 mm Bath depth 500 mm The size of the viewing window is 190x480 mm Weight 25 kg Power consumption 2.2 kW

It is designed to maintain a set temperature of a liquid coolant circulating both in an internal bath and in external consumers of a closed or open type. Pump for closed or open type thermostating systems. With a set of devices VT20-4K can be used for testing samples of asphalt concrete and oil bitumen. The operating temperature range is +20...+200 °C. Bath volume 20 l Overall dimensions 490x330x450 mm The open part of the bath is 240x200 mm Bath depth 210 mm Weight 16 kg Power consumption 2.2 kW.

The control cabinet of thermal equipment SHUP-260-1 in standard design is designed to control industrial single-zone furnaces with a maximum power of up to 260 kW and a voltage of 380 volts connected by a star or triangle. Serial products have control and monitoring systems based on the Modbus-RTU bus. On request, cabinets can be supplemented with backup power sources.

The working condition of the ND-1000 diffusion pump depends on the temperature of the working fluid in the pump boiler. During the initial filling, it is recommended to fill the maximum volume of the working fluid. The working fluid is "VACMA OIL 500" vacuum oil (under technical specifications TU 19.20.29-061-00218526-2019). The total amount of working fluid in the ND-1000 diffusion pump is a maximum of 23 liters, a minimum of 16 liters. The viewing window for visual inspection of the working fluid has marks of its maximum and minimum amounts. During normal operation of the pump, the level of the working fluid practically does not change. The temperature of the working fluid when the pump is operating at the maximum residual pressure is about 240°C to 255°C. It is recommended to monitor the operation of heaters in the ND-1000 diffusion pump using two temperature sensors. The temperature sensor must be installed in a special radiator socket above the heater. In the event that there is a loss of working fluid and an increase in the temperature of the radiators to 360 0C for the ND-1000 diffusion pump, the temperature sensor must give the command to automatically turn off the heaters. The subsequent activation of the pump heaters should not be automatic and should be performed only after cooling the system. Water at the inlet to the cooling systems of the housing and the oil reflector must be supplied with a pressure of 0.3 MPa (3 kgf/cm2) to 0.5 MPa (5 kgf/cm2) and a temperature of plus 4°C to plus 25°C. The recommended cooling water consumption for the housing is 1500 l/h, for the oil reflector 150 l / h and is regulated by the outlet water temperature, which should not exceed plus 40°C. The water drain should be free (with a jet break).

Vacuum membrane pump PL.HM02.01.6 Primelab is an effective device for creating a vacuum, as well as pumping gases and vapors. Depending on the tasks, you can achieve different device performance, which depends on the method of connecting the cameras. With a series connection, the capacity will be 38 l/min at a maximum vacuum of 6 mbar. Parallel connection of the chambers will lead to a pumping speed of 76 l/min at a maximum vacuum of 45 mbar, and an independent connection at the same vacuum will allow a performance of 38 l/min per chamber. The chemical-resistant diaphragm pump PL.HM02.01.6, developed and manufactured by the domestic company Primelab, meets IP20 protection class. It has a light weight of 8.6 kg and compact dimensions (321.5x140x200 mm). Helps you increase productivity and achieve flawless results in the laboratory.

Design features: Microprocessor temperature controller; Four-sided heating; Shut-off forced air circulation in the working chamber; The material of the chamber is steel painted with heat–resistant paint; Bright LED display; Conveniently located control panel; LED indicators of heater operation and protection operation; Alarm when the current temperature exceeds the limits of the permissible range; Reliable door closing mechanism; High-quality silicone sealer; Highly efficient thermal insulation of the housing; The case is made of high-quality sheet steel and painted with heat-resistant powder paint; Number of shelves: standard – 2, maximum – 8. Technical specifications: Maximum heating temperature, °C +300 The error of reproducing the set temperature, ° C ± 3 Temperature maintenance error, °C ± 1 Warm-up time to maximum temperature, no more, min 45 Dimensions of the working chamber, (WxHxD), not less than mm 440x465x430 Overall dimensions, (WxHxD), not more than mm 785x680x745 Rated supply voltage, 220 V Rated power, W 2200

The electric vacuum drying cabinet SHSV-65/5.0 is designed for drying and heating various materials in air and in vacuum at a maximum temperature of 500 ° C. In the model with the index "C", the door is made of heat- resistant glass. Technical specifications The electric cabinet operates at ambient temperature from 10 to 35 ° C and relative humidity up to 80% at 25 ° C Operating temperature- 500 ⁰C Power consumption - 5000 watts Dimensions of the working chamber-Ø430x430 mm Dimensions WxDxH- 680x990x620 mm Weight - 95* kg (* - mass with microprocessor unit and pump)

It is intended for thermostating samples in glasses, flasks and other laboratory utensils in cases when high accuracy of temperature maintenance is not required and good uniformity of the temperature field in the working volume is not needed. The operating temperature range is Current +5...+200 °C. One workplace with a diameter of 110 mm with five steel O-rings, tripods and feet with a clip. Stamped steel tub with a volume of 5 liters and a depth of 110 mm. The volume of the bath is 5 liters Overall dimensions 515x360x660 mm The open part of the bath is 295x145 mm Bath depth 110 mm Weight 7 kg Power consumption 2.5 kW

The power of the built-in electric heaters is 12 kW, there is also an independent emergency shutdown channel. The operating temperature range is +50...+200 °C. The volume of the bath is 30 liters Overall dimensions 500x840x880 mm Weight 60 kg Power consumption 13 kW (three-phase network)

Designation MCHV-10 Cooling capacity at Two.water= +15C, Tcond=+45C, Current.cp.=+30C, kW 10 Required pump capacity, m3/h 2,2 Pressure loss in the heat exchanger, kRa 40

Design features: Durable ceramic muffle; Closed heaters on four sides of the chamber; Microprocessor temperature controller; Conveniently located control panel and bright LED display; Ease of management and control; LED indicators of heater operation and protection operation; Automatic shutdown of heating when opening the door; The door opens up and faces the user with the cold side; Alarm when the current temperature exceeds the limits of the permissible range; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1100 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to the maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than mm 215x190x330 Overall dimensions, WxHxD, not more than mm 525x655x680 Rated supply voltage, 220 V Rated power, W 6000