CHEMICAL EXHAUST CABINET MODELS: LK-900, LK-1200, LK-1500, LK-1800 (all with a high-voltage fuse)

The Kors NV-1500 SHVD-U laboratory fume cupboard is a two—frame cabinet with a granite countertop with a width of 1410 mm and a small built-in sink made of polypropylene. External dimensions of the cabinet (W×D×H): 1410×700×1960 mm. Dimensions of the working area (W×D×H): 1378×540×750 mm. Table top: granite tiles. Working surface material: porcelain tile. It is moisture-resistant and perfectly withstands high temperatures. It is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Limited resistance to hydrofluoric acid. This is one of the most popular types of countertops for laboratory furniture. The small sink-drain is made of polypropylene, resistant to aggressive chemicals. Its diameter is 135 mm and its depth is 110 mm. The working area is closed by two lifting frames with a counterweight. As standard, there are two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1378×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the height of the cabinet will be 2470 mm. The NV-1500 SHVD-U fume cupboard is equipped with an LED lamp with a switch and two sockets, one of them with grounding. Sockets have the IP20 degree of protection, the maximum load on them: 1.5 kW. The working chamber is an all-welded metal frame in powder coating. Load-bearing laminated panels (chipboard with a thickness of 16 mm) are edged on the facade with a durable PVC edge with a thickness of 2 mm, which increases the impact resistance and mechanical strength of the products. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

BASIC EQUIPMENT Working box guide posts – aluminum profile painted with powder paint (RAL 7035/RAL 5023) in the right rack there is a light switch front anti–spill side - acid-resistant polished stainless steel AISI 304 side panels – tempered glass 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-780mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – metal painted with powder paint (RAL 5023) with the texture of shagreen leather back and top panels – polypropylene on the top panel: LED lamp dust- and moisture-proof 22W IP65 switching box with automatic emergency shutdown power supply 16A flange d=250mm (the distance from the back panel to the center of the flange is 170mm) easily removable exhaust canopies 3 exhaust levels (lower, side and front) counterweights are placed in the front pylon racks and are easily serviced Frame base metal pedestal painted with powder paint (RAL 7035) with the texture of shagreen leather facades – laminated MDF with a thickness of 16mm handles – polypropylene 2 compartments with locks 1 shelf with the possibility of installation on three levels in any of the compartments (when the cabinet is equipped with 2 bowls, shelves are not included) flange d=100mm service panel – aluminum profile painted with powder paint (RAL 5023) with the texture of shagreen leather: adjustable supports

Furniture for laboratory work. All-metal exhaust cabinet Working surface: FRIDURIT (20 mm) Overall dimensions: Length, mm: 1800 Depth, mm: 740 Height, mm: 2100 equipment Working box anti–spill side – acid–resistant polished stainless steel AISI 316 housing - metal painted with white powder paint (RAL 9016) guide posts – aluminum profile painted with dark gray powder paint (RAL 7011) 2 dependent lifting screens - tempered glass in aluminum frames, lifting 0-710mm, not change the dimensions of the cabinet when lifting.

Working surface: Porcelain stoneware (ceramic tile 300*300mm) Length, mm: 832 Depth, mm: 925 Height, mm: 2100 equipment Working box the side and back panels are lined with a row of ceramic tiles to a height of 400mm the case is melamine with a thickness of 16mm lifting screen with the possibility of fixing at any height – organic acrylic glass with a thickness of 8mm, lifting 0–750mm, increases the height of the cabinet with a full lift by 430mm

BASIC EQUIPMENT Working box the front guide posts are aluminum profile painted with powder paint (RAL 7035/RAL 5023), in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) the front anti–spill side is acid-resistant polished stainless steel. AISI 304 steel rear, upper, side panels – metal painted with powder paint (RAL 7035) with the texture of shagreen leather the inner surfaces of the working box are lined with chemically resistant HPL plastic 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-780mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – tempered glass in an aluminum frame on the upper panel: LED dust- and moisture-proof lamp (2X10W IP65) is separated from the workspace by tempered glass thickness of 4mm flange d=250mm (distance from the rear panel to flange center – 170mm) easily removable exhaust canopies 3 exhaust levels on the left side panel service module with cold water supply pipe and wall-mounted drain sink made of polypropylene cold water supply valve in the left rack of the box counterweights are placed in the front racks-pylons and are easily serviced Frame base collapsible frame made of rectangular metal profile painted with powder paint (RAL 7035) with the texture of shagreen leather service panel - aluminum profile painted with powder paint (RAL 7035/RAL 5023) with the texture of shagreen leather adjustable supports module with two drawers

BASIC EQUIPMENT: Working box front guide posts – aluminum profile painted with powder paint (RAL 7035/RAL 5023), in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) the front anti-spill side is acid-resistant polished stainless steel. AISI 316 steel rear, upper, side panels – metal painted with powder paint (RAL 7035) with the texture of shagreen leather inner capsule made of polypropylene lined with ceramic plates of the rear and side panels to a height of 380mm 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-780mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – polypropylene on the top panel: LED dust– and moisture-proof lamp 2x22 W (IP65) is separated from the workspace by tempered glass with a thickness of 4mm flange d=250mm (distance from the back panel to the center of the flange - 170mm) switching box with automatic emergency power off 16A 3 exhaust levels easily removable exhaust visors counterweights are placed in the front pylon racks and are easily serviced Frame base collapsible frame made of rectangular metal profile painted with powder paint (RAL 7035) with the texture of shagreen leather service panel - aluminum profile painted with powder paint (RAL 5023) with the texture of shagreen leather adjustable supports

The SHVM fume hood is designed for the installation of muffle furnaces and drying cabinets. It can be equipped with cabinets made of steel. 1. LC-900 SHVM Width - 960 GRANTEC - 72 550 ₽ 2. LC-900 SHVM with protective screen Width - 960 GRANTEC - 88 910 ₽ 3. LC-1200 SHVM Width - 1260 GRANTEC - 83 860 ₽ 4. LC-1200 SHVM with protective screen Width - 1260 GRANTEC - 100 390 ₽ 5. LC-1500 SHVM Width - 1560 GRANTEC - 95 270 ₽ 6. LC-1500 SHVM with protective screen Width - 1560 GRANTEC - 107 690 ₽

BASIC EQUIPMENT Working box guide racks – aluminum profile painted with powder paint (RAL 7035/RAL 5023)in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) the front anti-spill side is acid-resistant polished stainless steel AISI 304 side panels – tempered glass 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-780mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – metal painted with powder paint (RAL 5023) with the texture of shagreen leather on the top panel: LED lamp dust- and moisture-proof (10W IP65) switching box with automatic emergency power off 16A flange d=250mm (the distance from the back panel to the center of the flange is 170mm) easily removable exhaust canopies 3 levels of exhaust (lower, side and front) counterweights are placed in the front pylon racks and are easily serviced by the rear and upper panels – polypropylene Frame base collapsible frame made of rectangular metal profile painted with powder paint (RAL 7035) with the texture of shagreen leather service panel - metal box painted with powder paint (RAL 5023) with the texture of shagreen leather: adjustable supports

Working surface: Porcelain stoneware (ceramic tile 300*300mm) Length, mm: 1538 Depth, mm: 726 Height, mm: 2100 equipment Working box front anti–spill side - TRESPA TopLab sink-drain (polypropylene, internal size 250*100*150mm), pipe for water the package includes a corrugated siphon 2 flexible eyeliners with a length of 1200mm housing – melamine with a thickness of 16mm lifting screen with the possibility of fixing at any height – tempered glass with a thickness of 5mm, lifting 0-700mm, increase the height of the cabinet at full lifting by 450mm

BASIC EQUIPMENT guide racks – aluminum profile painted with powder paint (RAL 7035/ RAL 5023) in the right rack there are a light switch and 3 splash-proof sockets with a 3.2kW cover (IP54) in the left rack there are a water valve and a nitrogen valve, rear, upper, side panels - metal painted with powder paint (RAL 7035) with the texture of shagreen leather bottom – corrugated aluminum sheet 3mm 3 dependent lifting screens – tempered glass in aluminum profile frames, lifting 0-1800mm, do not change the dimensions of the cabinet when lifting, the middle and upper screens are equipped with sliding glass doors made of tempered glass with a thickness of 4mm upper fixed screen – metal, powder-painted paint (RAL 7035) with the texture of shagreen leather in the upper part and tempered glass in the lower part in an aluminum profile frame on the upper panel: LED lamp dust– and moisture-proof (2x22 W IP65) flange d=250mm (distance from the back panel to the center of the flange - 155mm) switching box with automatic emergency power off 16A 3 extraction levels technological opening d =50mm with a plug and outlet at the bottom of the right sidewall and right rear rack counterweights are placed in the front pylon racks and are easily serviced on the left side panel service module with cold water and nitrogen supply pipes on the service panel there is a wall-mounted drain sink made of polypropylene. (ext. size 250*100*150mm) pipe d/water pipe d/nitrogen

Working surface: Porcelain stoneware (ceramic tile 300*300mm) Length, mm: 938 Depth, mm: 726 Height, mm: 2100 equipment Working box front anti–spill side - TRESPA TopLab sink-drain (polypropylene, internal size 250*100*150mm), pipe for water the package includes a corrugated siphon 2 flexible eyeliners with a length of 1200mm housing – melamine with a thickness of 16mm lifting screen with the possibility of fixing at any height – tempered glass with a thickness of 5mm, lifting 0-700mm, increase the height of the cabinet at full lifting by 450mm

BASIC EQUIPMENT Working box the front guide posts are aluminum profile painted with powder paint (RAL 7035/RAL 5023), in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) the front anti-spill side is acid-resistant polished stainless steel. AISI 304 steel rear, upper, side panels – metal painted with powder paint (RAL 7035) with the texture of shagreen leather the inner surfaces of the working box are lined with chemically resistant HPL plastic 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-780mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – tempered glass in an aluminum frame on the top panel: LED dust- and moisture-proof lamp (2X10W IP65) is separated from the workspace by tempered glass thickness of 4mm flange d=250mm (distance from the back panel to flange center – 170mm) easily removable exhaust canopies 3 exhaust levels on the left side panel service module with cold water supply pipe and wall-mounted drain sink made of polypropylene cold water supply valve in the left rack of the box counterweights are placed in the front racks-pylons and are easily serviced Frame base collapsible frame made of rectangular metal profile painted with powder paint (RAL 7035) with the texture of shagreen leather service panel - aluminum profile painted with powder paint (RAL 7035/RAL 5023) with the texture of shagreen leather adjustable supports module with two drawers

BASIC EQUIPMENT Working box guide racks – aluminum profile painted with powder paint (RAL 7035/RAL 5023)in the right rack there are a light switch and 2 splash-proof sockets with a 3.2kW cover (IP54) the front anti–spill side is acid-resistant polished stainless steel AISI 304 side panels – tempered glass 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-780mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – metal painted with powder paint (RAL 5023) with the texture of shagreen leather back and top panels – polypropylene LED lamp dust- and moisture-proof (10W IP65) switching box with automatic emergency power off 16A flange d=250mm (the distance from the back panel to the center of the flange is 170mm) easily removable exhaust visors 3 exhaust levels (lower, side and front) counterweights are placed in the front pylon racks and are easily serviced The frame base is a collapsible frame made of a rectangular metal profile painted with powder paint (RAL 7035) with the texture of shagreen leather service panel is a metal box painted with powder paint (RAL 5023) with the texture of shagreen leather: adjustable supports.

Furniture for laboratory work. Exhaust cabinet made of chipboard Working surface: Trespa TopLab 6mm, on a substrate of wood-containing material (plywood 15mm, melamine 16mm). Overall dimensions: Length, mm: 1200 Depth, mm: 740 Height, mm: 2100 equipment Working box front anti–spill side - acid–resistant polished stainless steel AISI 316 housing - white chipboard with a thickness of 16mm guide posts – aluminum profile painted with powder paint dark gray (RAL 7011) 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-710mm, do not change the dimensions of the cabinet when lifting.

The Korsa NV-1500 SHV-PB laboratory fume cupboard is a single—frame cabinet with a width of 1410 mm with a table top made of polypropylene. External dimensions of the cabinet (W×D×H): 1410×700×1960 mm. Dimensions of the working area (W×D×H): 1378×540×750 mm. Table top: polypropylene. A reliable fume cupboard for laboratories Working surface material: monolithic polypropylene. It is moisture-resistant, resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Poorly resistant to high temperatures. Polypropylene countertops are suitable for chemical laboratories that work a lot with concentrated inorganic acids and alkalis. The working area is closed by a single lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1378×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, with the glass raised, the total height of the cabinet will be 2470 mm. The working area is illuminated by an LED lamp (included in the package). The switch is located on the right-hand side of the cabinet, next to the sockets. The fume cupboard is equipped with two sockets, one of them with grounding. Sockets have the IP20 degree of protection, maximum load: 1.5 kW. The base of the cabinet is an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

It is not recommended for use when working with concentrated inorganic acids, especially in cases related to their evaporation. It is also not advisable to store acids and alkalis in cabinets and drawers, even in closed containers and with a running ventilation system. 1. LC-900 SHV-METH Width - 960 GRANTEC - 109 420 ₽ LAB HPL- 116 350 ₽ POLYPROPYLENE- 113 290 ₽ 2.LC-1200 SHV-MET Width - 1260 GRANTEC - 124 660 ₽ LAB HPL- 133 750 ₽ POLYPROPYLENE-129 180 ₽ 3.LC-1500 SHV-METH Width - 1560 GRANTEC - 142 370 ₽ LAB HPL- 151 940 ₽ POLYPROPYLENE- 148 720 ₽ 4.LC-1800 SHV-MET Width - 1860 GRANTEC - 158 640 ₽ 202 970 ₽LAB HPL- 168 190 ₽ POLYPROPYLENE- 165 510 ₽

BASIC EQUIPMENT Working box front guide posts – aluminum profile painted with powder paint (RAL 7035/RAL 5023), in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) the front anti-spill side is acid-resistant polished stainless steel. steel (AISI 316) rear, upper, side panels – metal painted with powder paint (RAL 7035) with the texture of shagreen leather inner capsule made of polypropylene lined with ceramic plates of the rear and side panels to a height of 380mm 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-780mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – polypropylene on the upper panel: LED dust– and moisture-proof lamp 2x22 W (IP65) is separated from the workspace by tempered glass with a thickness of 4mm flange d=250mm (distance from the back panel to the center of the flange - 170mm) switching box with automatic emergency power off 16A 3 exhaust levels easily removable exhaust canopies the glass ceramic heating platform is located on the left side of the countertop size 640*500mm (working area 580*430mm, 2 independent heating zones) power up to 5.7kW heating up to 400 ° C counterweights are placed in the front pylon racks and are easily serviced Frame base collapsible frame made of rectangular metal profile painted with powder paint (RAL 7035) with the texture of shagreen leather service panel - aluminum profile painted with powder paint (RAL 5023) with the texture of shagreen leather adjustable supports