Metrology

The AC voltage source B2-7 is intended to provide devices and equipment with a stabilized AC voltage during the development, production, operation and repair of electronic devices. Main properties: Provides protection against overload and short circuits at the output. Has a light indication: - overload and short circuit protection tripping; - incorrect connection of the power supply line to B2-7. Technical specifications The nominal value of the output voltage (SKZ) 220 V The nominal value of the input and output voltage frequency is 50 Hz Output electrical power, not less than 1000 VA The main error in setting the output voltage is ± 2.2 V Additional error in setting the output voltage caused by a deviation of the input voltage by ± 10% from the nominal value of 220 V ± 1.0 V Additional error in setting the output voltage caused by a change in the load current from the maximum value to zero ± 2.0 V Instability of the output voltage for any 10 minutes during 8 hours of continuous operation, no more than ± 2.0 V Operating temperature range from -10 to 50 °C AC power supply 220 V, 50 Hz Power consumption, no more than 1200 VA Overall dimensions, mm 240x128x349 Weight, not more than 6.5 kg

The hydraulic rack TSK-600 is an automated auxiliary equipment for creating pressure. It is used for checking pressure gauges, pressure transducers, pressure switches and other pressure systems used at the enterprise. The presence of a precision pressure regulator and a built-in amplifier allows a user to create the necessary pressure with a discreteness of 1 kPa easily and accurately. To ensure the operation of the rack in the entire range, it is necessary to have a reference pressure of 0.85 MPa which comes from an external pressure source: a compressor, a KIP air network, a gas cylinder. For operation within the range from 0 to 2.5 MPa, the supply of reference pressure is not required. The TSK-600 hydraulic rack can be manufactured in a version with 2, 3, 4, or 5 stainless steel output ports for setting the reference and verifiable SI. Each output port is equipped with a quick-release adapter with an internal thread M20x1.5 or G1/2, due to which the installation of verifiable SI does not require the use of wrenches. To protect the hydraulic system of the rack from contamination, a replaceable filter of 100 microns is installed in each output port, and the discharge of the working fluid is carried out through a separate discharge line to an external tank. Additionally, the rack can be equipped with measuring channels for checking pressure transmitters and with an alarm unit for ECM. TSK-600 is a unique solution for a metrological laboratory, which makes it possible to facilitate the work of personnel as much as possible and optimize the process of pressure SI verification. Features: • Easy to operate and maintain. • Setting and adjusting the pressure with the movement of one finger. • Multiple output ports for more efficient verification process. • The protection against contamination.

The source is capable of operating both independently and as part of automated measuring systems with interfaces such as RS-232 and ETHERNET. Technical specifications Output voltage setting range (SCR) from 25 to 250 V The discreteness of the output voltage setting is 0.05 V The frequency setting range of the output voltage is from 40 to 500 Hz The discreteness of the output voltage frequency setting is 0.05 Hz Output electrical power, not less than 1000 VA The basic error of setting the output voltage is ± (0.005 Uv + 0.5 V) The basic error of setting the output voltage frequency is ± 0.1 Hz Additional error in setting the output voltage caused by a change in the load current from the maximum value to zero ± 0.5 V Instability of the output voltage for any 10 minutes during 8 hours of continuous operation, no more than ± 0.5 V Operating temperature range from minus 10 to 50 °C AC power supply 220 V, 50 Hz Power consumption, no more than 1300 VA Overall dimensions, mm 343x160x352 Weight, not more than 6.5 kg

When conducting a comprehensive sanitary and hygienic inspection of premises and workplaces to ensure control over biologically hazardous levels of the magnetic field according to SanPiN 2.2.4.3359-16 "Sanitary and epidemiological requirements for physical factors in the workplace". The MTM-02 design allows you to quickly monitor the levels of residual magnetization of surfaces and ends of products near welds.

The signals of the navigation receiver's second mark and the RF available for the customer`s use are generated simultaneously on two high-frequency outputs of the receiver board. In the presence of stable reception of signals from satellites of the GLONASS and GPS radio navigation systems, the board ensures the operation of the RF in the frequency binding mode according to the signals of the second timestamp (the so-called “disciplined” rubidium frequency standard mode) with a relative error of the actual value of the RF frequency of no more than ± 5.0.10-12.

The measuring recorder IS-203.1.1 is designed to measure and register temperature with a specified time interval between measurements by direct contact of the device with the measuring object. The features of the meter IS-203.1.1 Ease of operation. Reliability. The operating conditions of the meter IS-203.1.1 Ambient temperature, ° C: -30...+85. Relative humidity, %: no more than 80% at T = 35 ° C. Atmospheric pressure, kPa: 86...106.

It can be used as an accurate universal thermometer for contact temperature measurement of non-aggressive liquid, bulk and gaseous media. It can be connected to a computer for calibration and transmission of measurement results. • Range of temperature measurements -50...+200 °C The minimum immersion depth of the sensor is 75 mm Overall dimensions of the electronic unit 80x75x100 mm Weight 0.25 kg

It is designed to measure the temperature during the transportation of petroleum products, namely, to make a temperature correction for the volumetric expansion of petroleum products. The density of petroleum products decreases significantly with increasing temperatures, and the volume of the product increases, the kit "Oilman-1" allows temperature measurements for the subsequent calculation of the volumetric expansion of petroleum products. •

Designed to measure the temperature of gaseous materials without mechanical impurities and aggressive vapors, atmospheric pressure. The smart atmospheric pressure probe with built-in flash memory is designed to measure the temperature of gaseous materials without mechanical impurities and aggressive vapors, atmospheric pressure by direct contact of the probe with the measuring object and transmitting the measured value via Bluetooth to devices with the installed ThermoMonitor based on the Android program. Operating conditions of the SZDAP smart probe Ambient temperature, °C: -20...+55. Relative humidity, %: not more than 80 at T=35 °C. Atmospheric pressure, kPa: 86...106. Functionality of the smart probe SZDAP Measurement of physical quantities with a resolution of 0.01. Recording of measured values at intervals from 5 seconds to 23 hours 59 minutes 59 seconds (only smart probes with built-in memory). Transmitting data about measured physical quantities via Bluetooth to a device with the ThermoMonitor. The Android program is installed. Transmitting information about the state of charge of the built-in battery via Bluetooth to a device with the ThermoMonitor. The Android program isinstalled. Automatic transition to sleep mode after 50 seconds. The ability to connect an external power supply. Possibility of calibration.

The dosimetric control stand (SDK) is designed for continuous monitoring of the parameters of the radiation situation in the premises and technological systems of nuclear and nuclear hazardous production enterprises. KFOR can be used as a structural element of the lower level of automated radiation monitoring systems at nuclear power and industrial facilities related to the obtaining, processing, use and storage of radioactive materials.