Exhaust cabinet for muffle furnaces Mod. -1500 SHVMP

BASIC EQUIPMENT Working box front guide posts – aluminum profile painted with powder paint (RAL 7035/RAL 5023), in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) the front anti-spill side is acid-resistant polished stainless steel. AISI 304 steel rear, upper, side panels – metal painted with powder paint (RAL 7035) with the texture of shagreen leather 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-780mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – tempered glass in an aluminum frame on the top panel: 4 anti-explosion valves LED dust- and moisture-proof lamp (2x10W IP65) is separated from the workspace by tempered glass thickness of 4mm flange d=250mm (distance from rear panel to the center of the flange – 170mm) switching box with automatic emergency power off 16A easily removable exhaust visors 3 levels of exhaust on the rear panel: technological hole d = 60mm with a plastic plug counterweights are placed in the front pillars-pylons and are easily serviced Frame base collapsible frame made of rectangular metal profile painted with powder paint (RAL 7035) with the texture of shagreen leather front pillars - aluminum profile painted with powder paint (RAL 7035/RAL 5023) adjustable supports

NV-1200 SHV-M is the most low-budget exhaust cupboard of the NV line. It is single-frame, with a laminated countertop. It is intended mainly for analytical laboratories. External dimensions of the cabinet (W×D×H): 1100×700×1960 mm. Dimensions of the working area (W×D×H): 1068×540×750 mm. Table top: laminated chipboard. A minimalistic solution for your laboratory The NV-1200 SHV-M fume cupboard has a minimum of functions, which makes it the most inexpensive. The table top is made of laminated chipboard. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. The working area is closed by one lifting frame with a counterweight. It has two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1068×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, and at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, with the glass raised, the total height of the cabinet will be 2470 mm. The working area is illuminated by a fluorescent lamp (included in the package). The switch is located on the right side of the cabinet body. The base of the cabinet is made on an all-welded metal frame in powder coating. The side laminated panels (chipboard 16 mm thick) are edged on the facade with a durable PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a fairly uneven floor. And what are the other options? In the line of NV-1200 cabinets there is a cabinet with plumbing and a surface made of granite tiles, as well as cabinets without plumbing, and with a surface made of monolithic ceramics, stainless steel, chemically resistant plastic. They are exactly the same size as the NV-1200 SHV-M. If you need a minimalistic cabinet of large sizes, you could be interesteed in the NV-1500 SHV-M model.

BASIC EQUIPMENT Working box working surface – porcelain stoneware slabs working window height – 750mm housing – metal, painted with powder paint (RAL 7035) with the texture of shagreen leather lifting screen no lighting no flange ∅ 250mm (distance from the back panel to the center of the flange – 215mm) Frame base collapsible frame made of rectangular metal profile painted with powder paint (RAL 7035) with the texture of shagreen leather service panel – aluminum profile painted with powder paint (RAL 5023) with the texture of shagreen leather automatic emergency power off 16A two splash-proof sockets with a 3.2kW cover (IP54) adjustable supports

BASIC EQUIPMENT Working box guide racks – aluminum profile painted with powder paint (RAL 7035/RAL 5023)in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) the front anti-spill side is acid-resistant polished stainless steel AISI 304 side panels – tempered glass 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-780mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – metal painted with powder paint (RAL 5023) with the texture of shagreen leather back and top panels – polypropylene LED lamp dust- and moisture-proof (22W IP65) switching box with automatic emergency power off 16A flange d=250mm (the distance from the rear panel to the center of the flange is 170mm) easily removable exhaust visors 3 exhaust levels (lower, side and front) counterweights are placed in the front pylon racks and are easily serviced Frame base collapsible frame made of rectangular metal profile painted with powder paint (RAL 7035) with the texture of shagreen leather service panel – metal box painted with powder paint (RAL 5023) with the texture of shagreen leather: adjustable supports

The SHVM NVK 1200 MON is a metal fume cupboard for laboratory. The table top is made of monolithic ceramics, its width is 1200 mm. External dimensions of the cabinet (W×D×H): 1260×750×2250 mm. Internal dimensions of the camera (W×D×H): 1200×600×1168 mm. Table top material: monolithic ceramic. Reliable and durable construction The table top is made of a single ceramic plate with a width of 1200 mm. The seamless monolith of the countertop provides the highest reliability and durability. THe ceramics are great for all chemical laboratories, including those that work with substances at high temperatures. It perfectly tolerates heat, is moisture-resistant, resistant to acids and alkalis. High-temperature equipment (drying cabinets, muffle furnaces) can be placed on the table top. The cabinet has an all-welded metal frame covered with durable powder paint. All panels are made of polymer-coated metal. The front anti-spill side is made of polished stainless steel AISI-316. There are four exhaust zones in the working chamber: they are located in the hood of the exhaust box and just above the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. The hood area is also made of metal. The protective screen of the cabinet can be easily lifted with one hand. It folds up and when lifted does not increase the overall height of the cabinet. It is made of 4 mm tempered glass in an aluminum frame. The sockets and the switch of the LED lamp are located outside the working area, on the right-hand side of the front panel of the cabinet. The sockets are splash-proof and are designed for current up to 16 A and voltage up to 250 V. Next to the switch there is a toggle switch of the automatic emergency power off. The reagents needed for work can be placed in the lower cabinet also made of metal. The cabinet has three swing doors and one fixed shelf. It has its own hood (pipe diameter 100 mm), which can be connected to the general exhaust system of the cabinet using the nozzle included in the cabinet kit. The cabinet legs are adjustable in height, allowing you to place the cabinet even on a rather uneven floor. Advantages of the SHVM NVK 1200 MON cabinet A metal fume cupboard suitable for any laboratory; Durable, reliable and very convenient to use; The protective screen is made of tempered glass; A hood is built into the cabinet, reagents can be safely stored in it. Application of the SHVM NVK 1200 MON cabinet Exhaust laboratory cabinets are used when working with toxic and harmful volatile materials, with clean materials, with dissolution or decomposition under heat treatment, when conducting sample analysis. Fume cupboards of the NV-Comfort series are used in laboratories of the widest profile: at food and light industry enterprises, in higher educational and scientific institutions, in chemistry classrooms at school, in quality control centers, medical organizations.

The SHVM NVK 1500 MON+ is a large metal fume cupboard with plumbing fixtures for laboratory. The table top is made of monolithic ceramics, its width is 1200 mm. External dimensions of the cabinet (W×D×H): 1560×750×2250 mm. Internal dimensions of the camera (W×D×H): 1500×600×1168 mm. Table top material: monolithic ceramic. A reliable and durable fume cupboard for laboratory The table top is made of monolithic ceramics. It is perfect for all chemical laboratories, including those that work with substances at high temperatures. It perfectly tolerates heat, is moisture-resistant, resistant to acids and alkalis. High-temperature equipment (drying cabinets, muffle furnaces) can be placed on the countertop. The width of the ceramic plate is 1200 mm, that is, there will be one seam in the countertop. The cabinet is mounted on an all-welded metal frame covered with durable powder paint. All panels are made of polymer-coated metal. The front anti-spill side is made of polished stainless steel AISI-316. There are four exhaust zones in the working chamber: they are located in the hood of the exhaust box and just above the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. The hood area is also made of metal. The protective screen of the cabinet can be easily lifted with one hand. It folds up and when lifted does not increase the overall height of the cabinet. It is made of 4 mm tempered glass in an aluminum frame. The small sink-drain is made of polypropylene, it is resistant to aggressive chemicals. Its internal dimensions: 218×115×122 mm. The faucet is made of brass, covered with polypropylene. The sockets and the switch of the LED lamp are located outside the working area, on the right-hand side of the front panel of the cabinet. The sockets are splash-proof and are designed for current up to 16 A and voltage up to 250 V. Next to the switch there is a toggle switch of the automatic emergency power off. The reagents needed for work can be placed in the lower cabinet. The cabinet is also made of metal. It has three swing doors and one fixed shelf. It has its own hood (pipe diameter 100 mm), which can be connected to the general exhaust system of the cabinet using the nozzle included in the cabinet kit. The cabinet legs are adjustable in height, allowing you to place the cabinet even on a rather uneven floor. Advantages of the SHVM NVK 1500 MON+ cabinet A metal fume cupboard with plumbing, suitable for any laboratory; The wide table top allows you to organize the workplace as conveniently as possible; It is durable, reliable and very convenient to use; The protective screen is made of tempered glass; The hood is built into the cabinet, reagents can be safely stored in it. Application of the SHVM NVK 1500 MON+ cabinet Exhaust laboratory cabinets are used when working with toxic and harmful volatile materials, with clean materials, with dissolution or decomposition under heat treatment, when conducting sample analysis. Exhaust cabinets of the NV-Comfort series are used in laboratories of the widest profile: at food and light industry enterprises, in higher educational and scientific institutions, in chemistry classrooms at school, in quality control centers, medical organizations.

Working surface: Porcelain stoneware (ceramic tile 300*300mm) Length, mm: 1500 Depth, mm: 740 Height, mm: 2100 Working box the working surface is ceramic tile, resistant to concentrated acids, alkalis, organic solvents and high temperatures) the size of the working space – 1430*600* 1090mm front anti–spill side - TRESPA TopLab sink-drain (polypropylene, internal size 250*100*150mm), water pipe the package includes a siphon, a gofroflang, 2 flexible eyeliners with a length of 1200mm the body is metal, painted with white powder paint 2 dependent lifting screens with the possibility of fixing at any height – tempered glass with a thickness of 5mm in aluminum frames, lifting 0-700mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – metal painted with white powder paint

BASIC EQUIPMENT Working box front guide posts – aluminum profile painted with powder paint (RAL 7035/RAL 5023), in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) front anti–spill side - polypropylene working surface - polypropylene 15mm thick removable plate 600*600mm with a ceramic granite work surface for placement heating plates (2 pcs.) 2 dependent lifting screens filled with transparent PVC, 5mm thick in a polypropylene frame in the lower screen – sliding doors made of transparent PVC with a thickness of 5mm lifting 0-780mm, does not change the dimensions of the cabinet when lifting the counterweights are placed in the front pillars-pylons and are easily serviced upper fixed screen – polypropylene inner part the working box is a fully sealed polypropylene capsule with a back wall washing system, a drainage channel and a polypropylene pipe for cold water 3 levels of hoods easily removable polypropylene exhaust canopies polypropylene drain sink on the top panel are placed: LED dust- and moisture-proof lamp (2X22W IP65) separated from the workspace by transparent PVC switching box with automatic emergency power off 16A flange with damper plug for air inflow d=200mm flange with aspiration collector for air outflow d=250mm (distance from the rear panels up to the center of the flange – 155mm) cabinet ventilation system

The SHVM fume hood is designed for the installation of muffle furnaces and drying cabinets. It can be equipped with cabinets made of steel. 1. LC-900 SHVM Width - 960 GRANTEC - 72 550 ₽ 2. LC-900 SHVM with protective screen Width - 960 GRANTEC - 88 910 ₽ 3. LC-1200 SHVM Width - 1260 GRANTEC - 83 860 ₽ 4. LC-1200 SHVM with protective screen Width - 1260 GRANTEC - 100 390 ₽ 5. LC-1500 SHVM Width - 1560 GRANTEC - 95 270 ₽ 6. LC-1500 SHVM with protective screen Width - 1560 GRANTEC - 107 690 ₽

Furniture for laboratory work. Exhaust cabinet made of chipboard Working surface: FRIDURIT (20 mm) Overall dimensions: Length, mm: 1800 Depth, mm: 740 Height, mm: 2100 equipment Working box front anti–spill side - acid–resistant polished stainless steel AISI 316 housing - white chipboard with a thickness of 16mm guide posts – aluminum profile painted with powder paint dark gray (RAL 7011) 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-710mm, do not change the dimensions of the cabinet when lifting.

Furniture for laboratory work. Exhaust cabinet made of chipboard Working surface: Trespa TopLab 6mm, on a substrate of wood-containing material (plywood 15mm, melamine 16mm). Overall dimensions: Length, mm: 900 Depth, mm: 740 Height, mm: 2100 equipment Working box front anti–spill side - acid–resistant polished stainless steel AISI 316 housing - white chipboard with a thickness of 16mm guide posts – aluminum profile painted with powder paint dark gray (RAL 7011) 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-710mm, do not change the dimensions of the cabinet when lifting.

Furniture for laboratory work. Exhaust cabinet made of chipboard Working surface: Porcelain stoneware (ceramic tile 300*300mm), stitching - epoxy compound Overall dimensions: Length, mm: 1800 Depth, mm: 740 Height, mm: 2100 equipment Working box front anti–spill side - acid–resistant polished stainless steel AISI 316 housing - white chipboard with a thickness of 16mm guide posts – aluminum profile painted with powder paint dark gray (RAL 7011) 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-710mm, do not change the dimensions of the cabinet when lifting.

Furniture for laboratory work. All-metal exhaust cabinet Working surface: Porcelain stoneware (ceramic tile 300*300mm), stitching - epoxy compound Overall dimensions: Length, mm: 900 Depth, mm: 740 Height, mm: 2100 equipment Working box front anti–spill side - acid–resistant polished stainless steel AISI 316 housing - metal painted with white powder paint (RAL 9016) guide posts – aluminum profile painted with dark gray powder paint (RAL 7011) 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-710mm, do not change the dimensions of the cabinet when lifting.

Furniture for laboratory work. Exhaust cabinet made of chipboard Working surface: Trespa TopLab 6mm, on a substrate of wood-containing material (plywood 15mm, melamine 16mm). Overall dimensions: Length, mm: 1800 Depth, mm: 740 Height, mm: 2100 equipment Working box front anti–spill side - acid–resistant polished stainless steel AISI 316 housing - white chipboard with a thickness of 16mm guide posts – aluminum profile painted with powder paint dark gray (RAL 7011) 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-710mm, do not change the dimensions of the cabinet when lifting.

Furniture for laboratory work. All-metal exhaust cabinet Working surface: Trespa TopLab 6mm, on a substrate of wood-containing material (plywood 15mm, melamine 16mm). Overall dimensions: Length, mm: 1200 Depth, mm: 740 Height, mm: 2100 equipment Working box front anti–spill side - acid–resistant polished stainless steel AISI 316 housing - metal painted with white powder paint (RAL 9016) guide posts – aluminum profile painted with dark gray powder paint (RAL 7011) 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-710mm, do not change the dimensions of the cabinet when lifting.

Furniture for laboratory work. All-metal exhaust cabinet Working surface: FRIDURIT (20 mm) Overall dimensions: Length, mm: 1200 Depth, mm: 740 Height, mm: 2100 equipment Working box front anti–spill side - acid–resistant polished stainless steel AISI 316 housing - metal painted with white powder paint (RAL 9016) guide posts – aluminum profile painted with dark gray powder paint (RAL 7011) 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-710mm, do not change the dimensions of the cabinet when lifting.

Furniture for laboratory work. All-metal exhaust cabinet Working surface: Trespa TopLab 6mm, on a substrate of wood-containing material (plywood 15mm, melamine 16mm). Overall dimensions: Length, mm: 1800 Depth, mm: 740 Height, mm: 2100 equipment Working box front anti–spill side - acid–resistant polished stainless steel AISI 316 housing - metal painted with white powder paint (RAL 9016) guide posts – aluminum profile painted with dark gray powder paint (RAL 7011) 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-710mm, do not change the dimensions of the cabinet when lifting.