Equipment

Appointment: continuous pumping of atmospheric air with a constant flow rate through a filter element based on Petryanova fabric. measurement of ionizing radiation parameters at a controlled point in accordance with the capabilities of the unit used.

The AC voltage source B2-7 is intended to provide devices and equipment with a stabilized AC voltage during the development, production, operation and repair of electronic devices. Main properties: Provides protection against overload and short circuits at the output. Has a light indication: - overload and short circuit protection tripping; - incorrect connection of the power supply line to B2-7. Technical specifications The nominal value of the output voltage (SKZ) 220 V The nominal value of the input and output voltage frequency is 50 Hz Output electrical power, not less than 1000 VA The main error in setting the output voltage is ± 2.2 V Additional error in setting the output voltage caused by a deviation of the input voltage by ± 10% from the nominal value of 220 V ± 1.0 V Additional error in setting the output voltage caused by a change in the load current from the maximum value to zero ± 2.0 V Instability of the output voltage for any 10 minutes during 8 hours of continuous operation, no more than ± 2.0 V Operating temperature range from -10 to 50 °C AC power supply 220 V, 50 Hz Power consumption, no more than 1200 VA Overall dimensions, mm 240x128x349 Weight, not more than 6.5 kg

The hydraulic rack TSK-600 is an automated auxiliary equipment for creating pressure. It is used for checking pressure gauges, pressure transducers, pressure switches and other pressure systems used at the enterprise. The presence of a precision pressure regulator and a built-in amplifier allows a user to create the necessary pressure with a discreteness of 1 kPa easily and accurately. To ensure the operation of the rack in the entire range, it is necessary to have a reference pressure of 0.85 MPa which comes from an external pressure source: a compressor, a KIP air network, a gas cylinder. For operation within the range from 0 to 2.5 MPa, the supply of reference pressure is not required. The TSK-600 hydraulic rack can be manufactured in a version with 2, 3, 4, or 5 stainless steel output ports for setting the reference and verifiable SI. Each output port is equipped with a quick-release adapter with an internal thread M20x1.5 or G1/2, due to which the installation of verifiable SI does not require the use of wrenches. To protect the hydraulic system of the rack from contamination, a replaceable filter of 100 microns is installed in each output port, and the discharge of the working fluid is carried out through a separate discharge line to an external tank. Additionally, the rack can be equipped with measuring channels for checking pressure transmitters and with an alarm unit for ECM. TSK-600 is a unique solution for a metrological laboratory, which makes it possible to facilitate the work of personnel as much as possible and optimize the process of pressure SI verification. Features: • Easy to operate and maintain. • Setting and adjusting the pressure with the movement of one finger. • Multiple output ports for more efficient verification process. • The protection against contamination.

The source is capable of operating both independently and as part of automated measuring systems with interfaces such as RS-232 and ETHERNET. Technical specifications Output voltage setting range (SCR) from 25 to 250 V The discreteness of the output voltage setting is 0.05 V The frequency setting range of the output voltage is from 40 to 500 Hz The discreteness of the output voltage frequency setting is 0.05 Hz Output electrical power, not less than 1000 VA The basic error of setting the output voltage is ± (0.005 Uv + 0.5 V) The basic error of setting the output voltage frequency is ± 0.1 Hz Additional error in setting the output voltage caused by a change in the load current from the maximum value to zero ± 0.5 V Instability of the output voltage for any 10 minutes during 8 hours of continuous operation, no more than ± 0.5 V Operating temperature range from minus 10 to 50 °C AC power supply 220 V, 50 Hz Power consumption, no more than 1300 VA Overall dimensions, mm 343x160x352 Weight, not more than 6.5 kg

The ZVPlE-500 shutter consists of a housing with connecting flanges, a shutter mechanism, a lip seal to ensure the tightness of the drive element, cover, and electric drive. The shutter mechanism consists of a carriage, an upper and lower flap, which are pulled together by springs and balls. The carriage moves along the housing guides on bearings. The ZVPlE-500 shutter is opened and closed both by electric drive and manually using a flywheel. To switch to manual control mode, there is a switching device on the electric drive. The manual drive is used to adjust and regulate the shutter. ZVPlE-500 valves are manufactured in climatic versions UHL (i.e. for moderate and cold climate) and O (i.e. general) 4 according to GOST standard 15150-69.

When conducting a comprehensive sanitary and hygienic inspection of premises and workplaces to ensure control over biologically hazardous levels of the magnetic field according to SanPiN 2.2.4.3359-16 "Sanitary and epidemiological requirements for physical factors in the workplace". The MTM-02 design allows you to quickly monitor the levels of residual magnetization of surfaces and ends of products near welds.

The 2ZVE-160 vacuum shutter with electromechanical drive equipped with 160mm conditional passages is designed to overlap vacuum systems in the range of operating pressures from 1x10-6 to 1.07x105 Pa (0.75x10–8 to 800 mm Hg). The 2ZVE-160 shutter is pendulum-type. The 23VE-160 shutter is manufactured in the climatic version UHL (i.e. for moderate and cold climate) and O (i.e. general) 4 according to GOST standard 15150-69. The working environment is air and non–aggressive gases. It is not intended for use in fire and explosive hazardous industries. The 23VE-160 shutter meets the requirements of technical specifications TU 3648-040-00218526-2003. According to the method of protecting a person from electric shock, the gate belongs to Class I electrical equipment according to GOST 12.2.007.0-75.

The signals of the navigation receiver's second mark and the RF available for the customer`s use are generated simultaneously on two high-frequency outputs of the receiver board. In the presence of stable reception of signals from satellites of the GLONASS and GPS radio navigation systems, the board ensures the operation of the RF in the frequency binding mode according to the signals of the second timestamp (the so-called “disciplined” rubidium frequency standard mode) with a relative error of the actual value of the RF frequency of no more than ± 5.0.10-12.

The measuring recorder IS-203.1.1 is designed to measure and register temperature with a specified time interval between measurements by direct contact of the device with the measuring object. The features of the meter IS-203.1.1 Ease of operation. Reliability. The operating conditions of the meter IS-203.1.1 Ambient temperature, ° C: -30...+85. Relative humidity, %: no more than 80% at T = 35 ° C. Atmospheric pressure, kPa: 86...106.

It can be used as an accurate universal thermometer for contact temperature measurement of non-aggressive liquid, bulk and gaseous media. It can be connected to a computer for calibration and transmission of measurement results. • Range of temperature measurements -50...+200 °C The minimum immersion depth of the sensor is 75 mm Overall dimensions of the electronic unit 80x75x100 mm Weight 0.25 kg