Chamber electric resistance furnace CHO-6.12.4

The electric furnace SNVS-1,5.2,0/10SHM10 is designed for heat treatment in vacuum, according to the technological process. The execution Of The Electric Furnace is mine. The type of cage is monoblock or composite. The loading direction is vertical. The loading method is by universal shop lifting mechanisms.

Vacuum resistance furnaces are necessary for heating products before pressure treatment, for sintering, degassing, quenching, annealing, soldering and chemical-technological processes. Such furnaces among all the variety of thermal equipment are considered the most environmentally friendly – heat treatment is carried out at t up to +2500 ° C in a purified vacuum. Under certain conditions, vacuum furnaces are used to work with neutral gases. The outer part of the furnace is made of stainless steel and is cooled by liquid. The inner part of the working chamber, where the heat treatment of materials is carried out, is made of an alloy of molybdenum and tungsten. The components are characterized by a low inertia force, reduced gas separation. The settings are available on the control panel, where the instruments, automatic and manual control switches are located. At every enterprise of the electronic industry, nuclear power, an explosion-proof vacuum resistance furnace is needed. The same applies to areas where various products undergo heat treatment at the stage of production and preparation for use.

Designation SSO-16.14/11 Power, kW 150 Diameter, mm 1600 Height, mm 1400

Designation: SNOT-12.16.16/1,2- I2-In Temperature 0C: 120 Door opening: manual Hearth drive: electromechanical Camera Size (WSHG): 1600x1200x1600 Fan: Yes

The rotating furnace of indirect electric heating SBO-2,5.13/10-I2PV is designed for firing powdered ores to convert them into an oxide form at temperatures up to 1000 oC.

Designation SSO-4.12/11 Power, kW 50 Diameter, mm 400 Height, mm 1200

The flaw detector allows continuous monitoring of polymer, epoxy and enamel coatings of pipelines with a diameter from 219 to 1420 mm and selective control of polymer, epoxy, enamel and bitumen coatings of pipelines of any diameter. The flaw detector provides detection of local through defects of insulation coatings of pipelines with a dry surface. The flaw detector allows for continuous monitoring The flaw detector uses an electric spark control method. The flaw detector is designed to work at: - ambient temperature, °C: from minus 30 to plus 50; - relative humidity at a temperature of +25°C, %: 98; - atmospheric pressure, kPa: from 84.0 to 106.7. Technical specifications. Test voltage, kV: up to 40 Minimum diameter of detected defects, mm: 0.6±0.2 Operating temperature range, °C: -30...+50 Power supply -from the built-in 12V battery -from an external DC power supply current with a voltage of 12 V Continuous operation time, h: 8 Operating mode setting time, min: 1 Overall dimensions, mm, no more: - control and monitoring unit 200 x 158 x 91 - high voltage transformer 410x f90 Weight, kg, no more,: - control and monitoring unit 2.5 - high voltage transformer 1.5 Defect alarm light and sound The kit includes: Bag Suitcase Battery charger Earthing device Electronic Magnet Unit Probes for continuous monitoring- 5 pcs 0 – 400 mm; 1 – 650 mm; 2 – 735 mm; 3 – 840 mm; 4 – 980 mm. Probes for local control - 3 pcs VT-1 High voltage transformer Pin Probe extension Holder Bushing Nipple - 4pcs set of documentation (passport, manual, calibration)

Vacuum compression furnace SNVS-4,5.5,5/3-I2PD is designed for drying, degassing in vacuum and under pressure at temperatures up to 300 0C.

Electric resistance furnace tubular laboratory SUOL-0,9.7/15 is designed for heat treatment of various materials and other work at a temperature of 1500oC.

Vacuum resistance furnaces are necessary for heating products before pressure treatment, for sintering, degassing, quenching, annealing, soldering and chemical-technological processes. Such furnaces among all the variety of thermal equipment are considered the most environmentally friendly – heat treatment is carried out at t up to +2500 ° C in a purified vacuum. Under certain conditions, vacuum furnaces are used to work with neutral gases. The outer part of the furnace is made of stainless steel and is cooled by liquid. The inner part of the working chamber, where the heat treatment of materials is carried out, is made of an alloy of molybdenum and tungsten. The components are characterized by a low inertia force, reduced gas separation. The settings are available on the control panel, where the instruments, automatic and manual control switches are located. At every enterprise of the electronic industry, nuclear power, an explosion-proof vacuum resistance furnace is needed. The same applies to areas where various products undergo heat treatment at the stage of production and preparation for use.

Designation SSHOL-3/11 Supply voltage, 220 ± 10% Network frequency, Hz 50 Power consumption, W, max 2500

Designation SNO(H)-6/12.5 Power, kW, no more than 8 Supply network voltage, V 380 Frequency, Hz 50

Designation SNO 5/17 Power, kW, no more 8 Volume, l 5,8 Supply network voltage, V 380 Frequency, Hz 50 Temperature 1700 Vacuum 10 mm Protective/oxidizing environment Management Thermodat + PLC

Designation SSO-12.13/11 Power, kW 90 Diameter, mm 1200 Height, mm 1300

Designation SNO 17/17 Rated power Pmax, kW 10 Power supply voltage U, In 3 phases + N+PE 380 Maximum operating temperature T slave, oS 1700

Designation SNO-80 Volume, l 80 The material of the working chamber is ceramic Heating 4 sides Power consumption, W, max 12000 Minimum operating temperature, 0C 100

High-temperature furnaces are capable of heating materials up to 1700 degrees. The scope of their application covers the heat treatment of various materials in an inert medium or vacuum. TULA-TERM furnaces are used for heat treatment of plastics, ceramics, metals, alloys, lacquers and other materials. The equipment allows sintering, annealing, soldering, quenching, drying, burning and molding. In industry, our installations are most often used for quenching parts and sintering hard alloys.