Sound and Vibration Analyzer ASHV-004

DPSS lasers of the KLM-589/x series are diode-pumped solid-state lasers of the visible spectral range (589 nm) with collimated continuous radiation of low and high power (depending on the model). The package includes: a laser head, a power supply, a set of connecting wires, a power cable and a device passport. Depending on the tasks, the following options are available for each laser model: the presence of TTL modulation / the presence of analog modulation, power control via the power supply, the presence of a display for the power supply, improved power instability (<3% / <1%), improved temporary power instability (4 h / 8 h), radiation sweep in-line (5...120°), laser head with fiber output (FC/SMA), extended warranty period, custom housing development. These lasers are widely used in medical equipment, for control and automation of technological processes, in scientific research, astronomy, spectroscopy. They are optimal sources of coherent radiation for the construction of systems of alignment and marking devices.

A membrane nitrogen station is a set of equipment for the production and supply of nitrogen under high pressure obtained from atmospheric air by the method of membrane separation. Unlike the membrane nitrogen plant, the membrane nitrogen station is equipped with additional equipment: a booster compressor that creates the necessary pressure. Put the squeeze on the pump. Composition of a typical membrane nitrogen station: 1. Air compressor 2. Dehumidifier 3. Main filter block, including coal column 4. Air receiver 5. Membrane nitrogen generator 6. Nitrogen receiver 7. Nitrogen booster compressor putting the squeeze on

It is intended for use in higher and secondary educational institutions during laboratory workshops on training specialists in engineering and technical specialties and natural science disciplines. Technical specifications: Upost.- 0.1 mV - 500 V; Uperem.- 1 mV-300 V (40 Hz-20 kHz) Ippost. - 0.1 mkA- 2 A; Iperem. - 1.0 mkA - 2 A (40 Hz-1 kHz) Rpost. - 0.1 Ohm – 20 mOhm Generation of triangles, pilobr., "meander", sinusoid. signal in the frequency range 0.1 Hz – 1 MHz Frequency measurement in the range of 0.1 Hz – 1 MHz The form of the measured signals is sine, pulse Constant voltage: at a current of 1 A - + 5 V at a current of 0.5 A for each channel - ± 12 V Adjustable Uppost. at a current of up to 1 A - 0 – 30 V Dimensions - 170x340x380 mm Power supply – 230 V, 50 Hz, 200 VA - max. Weight – 8.0 kg

KLM-M650-4-5 laser modules are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.

DPSS lasers of the KLM-523/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.

A series of modern intelligent relay protection, automation and alarm units PARMA IED-EP+ is designed for use in networks with a voltage from 6 to 750 kV

Operating Mode: Continuous Output stabilized current, A: 1-80 Output voltage, V: 0-35 Power supply: Three-phase 220/380 V 50 Hz Operating temperature range, °C: +10...+35 Storage temperature, °C: -20...+45 Relative humidity (without condensation), %: 90 Weight, kg: 5.3 Overall dimensions (W x H x D), mm: 390 x 75 x 200

DPSS lasers of the KLM-515/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.

Technical specifications: Indicator name, unit of measurement, Indicator value, B5-89, B5-89/1 The range of the output voltage setting, the limits of the absolute error of the output voltage setting:- basic error, In; - in operating conditions, In, from 0 to 30.0 ± 0.2± 0.3, from 0 to 100.0 ± 0.3± 0.45 The range of the output current setting, the limits of the absolute error of the output current setting:- basic error, A; - in operating conditions, A, from 0 to 10.0 ± 0.2± 0.3, from 0 to 3.0 ± 0.1± 0.15 Instability of the output voltage when the supply voltage changes by ± 10% of the nominal value in the voltage stabilization mode, %, ± 0.05, no more, Instability of the output current when the supply voltage changes by ± 10% of the nominal value in the current stabilization mode, %, ± 0.2, no more, Instability of the output voltage when the load current changes at the output terminals of power supplies in voltage stabilization mode, %, ± 1, no more, Instability of the output current when the load voltage changes in the current stabilization mode at minimum load currents, %, ± 5, no more, Instability of the output current when the load voltage changes in the current stabilization mode at maximum load currents, %, ± 0.5, no more, Output voltage ripple in voltage stabilization mode, mV, 1.0, no more, Output current ripple in current stabilization mode, %, 1, no more, Instability of the output voltage from time, V, ± 0.5, ± 1.0 Instability of the output current from time, A, ± 0.3, ± 0.2 AC power supply: - voltage, V; - frequency, Hz, 230 ± 2350 ± 0.5, Weight, kg, 13.0, no more, Overall dimensions, mm, 384x301x169

Provita Company designs and manufactures nitrogen compressor stations based on sea containers (10, 20, 30, 40–feet) and sandwich panel block boxes with standard dimensions and fasteners, which allows them to be transported by road, rail and sea transport. A mobile compressor unit can be carried out on an automobile chassis or on a sled for transportation to remote hard-to-reach regions. The nitrogen compressor station can be supplied in various climatic versions: northern (ambient temperature up to -55°C) standard (from -45 to +45°C) tropical (up to +55°C)

It is designed to measure relative humidity and air temperature in industrial, warehouse and residential premises, in climatic chambers and technological highways, in open areas (weather stations). Technical specifications: Measurement of relative humidity measuring range (10-100) % resolution 0.1% basic measurement error ± 3% Temperature measurement measuring range (-60 ... +300) ° C resolution 0.1 °C measurement error ± (0.5 - 1.5) ° C Power supply network adapter, built-in battery USB 2.0 interface Weight 1.5 kg The verification interval is 1 year

The helium leak detector TI1-50M is a universal highly sensitive device designed to test the tightness of various systems and objects that allow pumping out the internal cavity, as well as those filled with helium or a mixture containing helium, and detect (localize) places of leakage (leaks). Specifications: Measuring range at the leak detector inlet, Pa•m3/s from 5•10-13 to 1•10-5; Range of indications when working by probe method, Pa•m3/s from 1•10-9 to 1•10-5; Time to enter the readiness mode for measurements, no more than, min 5; AC supply voltage, V, Hz 220±10%, 50±1; Power consumption, VA 1200; Overall dimensions (WxHxD), no more than, mm 480x470x390; Weight, no more than, kg 40; Average time to metrological failure, h 15000;

DPSS lasers of the KLM-532/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.

USVI(PMU) functionality: · Supports computing and data transmission in on-line mode via the C37.118-2011 protocol · have two built-in Ethernet interfaces for connecting to the LAN of the installation object · save data for later access via FTP – off-line mode