Hydrophone GI59

Laser modules of the KLM-A980-5-5 series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.

A membrane nitrogen plant is a set of special equipment designed to produce nitrogen from atmospheric air by the method of membrane separation at a pressure of up to 25 bar. The production of nitrogen in this technological process is based on the principle of separation of gas mixtures in a membrane module, due to the different penetration rates of the components of the gas mixture through polymer membranes and the differential partial pressures on both sides. In the case of separation of the air mixture, oxygen has a greater permeability than nitrogen. The difficult-to-penetrate gas components (N2, CH4, CO) pass along the entire length of the generator and then come to the consumer. The output is a gas mixture with an N2 content of up to 99.9%. The membrane installation allows to obtain high-pressure production gas (nitrogen). The composition of a standard membrane nitrogen production plant: Air compressor; Dehumidifier; Main filter block, including coal column; Air receiver; Membrane generator; Production gas receiver.

DPSS lasers of the KLM-532/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.

DPSS lasers of the KLM-420/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes. Technical specifications Radiation output power: up to 10W Radiation wavelength: 420 nm Output beam diameter: 1.5mm Divergence of the radiation beam: 1.3 mrad Instability of radiation power: 5% Type of modulation: TTL or analog Time to enter the mode: 15min Spectral line width: 0.1nm

DPSS lasers of the KLM-627/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.

CDL lasers of the KLM-808-x series are optimal sources of continuous radiation for the construction of control and automation systems, for scientific and medical purposes.

Receiving and transmitting modules for electrical communication lines in SFP metal cases with separate optical input/output for an RJ-45 type electrical connector to transmit the signal over two optical fibres.

DPSS lasers of the KLM-447/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes. Technical specifications Radiation output power: up to 120W Radiation wavelength: 447 nm Output beam diameter: 1.5mm Divergence of the radiation beam: 1.3 mrad Instability of radiation power: 5% Type of modulation: TTL or analog Time to enter the mode: 15min Spectral line width: 0.1nm

The nitrogen adsorption generator is a special equipment designed to produce nitrogen gas from atmospheric air by the method of short-cycle non-heating adsorption. Capacity:1.8—1000 m3/h Purity: 99.99—99.9999 % Pressure: 4-450 bar

The advantage of the system using a closed-cycle helium cooling unit from Helix Technology Corporation (USA) is the ability to provide low measurement temperatures (up to 10 K) without loss of consumables (helium) with a compact arrangement of equipment. Isolation of the studied absorber from vibration associated with the operation of the compressor is ensured by ensuring heat exchange of the absorber with the cooling head of the unit through an intermediate layer of helium gas and by careful vibration isolation of the systems of the Mossbauer spectrometer, minimizing additional broadening of the spectrum lines during operation of the cooling unit. All modes and characteristics of the MS-1104Em Mossbauer spectrometer are preserved at the same time.

CDL lasers of the KLM-780-150 series are optimal sources of continuous radiation for the construction of control and automation systems, for scientific and medical purposes.

SFP+ Direct Attach Cable manufactured by Optronic is a passive Twinax cable with a length of 1 to 5 meters, the operating data transfer rate is up to 10 Gbits. SFP+ DAC are compatible with Ethernet equipment of such brands as Cisco, Extreme, Juniper, HP, Dell, Force10, Huawei, Dlink, etc.

It is intended for use in higher and secondary educational institutions during laboratory workshops on training specialists in engineering and technical specialties and natural science disciplines. Technical specifications: Upost.- 0.1 mV - 500 V; Uperem.- 1 mV-300 V (40 Hz-20 kHz) Ippost. - 0.1 mkA- 2 A; Iperem. - 1.0 mkA - 2 A (40 Hz-1 kHz) Rpost. - 0.1 Ohm – 20 mOhm Generation of triangles, pilobr., "meander", sinusoid. signal in the frequency range 0.1 Hz – 1 MHz Frequency measurement in the range of 0.1 Hz – 1 MHz The form of the measured signals is sine, pulse Constant voltage: at a current of 1 A - + 5 V at a current of 0.5 A for each channel - ± 12 V Adjustable Uppost. at a current of up to 1 A - 0 – 30 V Dimensions - 170x340x380 mm Power supply – 230 V, 50 Hz, 200 VA - max. Weight – 8.0 kg