UV BACTERICIDAL MOBILE AIR RECIRCULATOR IRRADIATOR "ORUBP-3-5- "KRONT" (DESAR-7)

Laser modules of the KLM-B808-x-5 series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.

Implements a thermogravimetric (air-thermal) method for determining the mass fraction of moisture, based on measuring the mass of the sample of the analyzed substance before and after drying, followed by calculating the values of the mass fraction of moisture. Air-thermal measuring installations ASESH-8 are registered in the State Register of Measuring Instruments under No. 58526-14, have a certificate of approval of the type of measuring instruments OC.C.31.005 And No. 56847.The installations undergo initial verification and have the appropriate certificate. General characteristics: - The presence of two independent drying chambers. - Possibility of simultaneous determination of humidity of 12 samples: Each drying chamber of the installation consists of 6 independent cells. You can put 2 buckets in each cell. Total capacity of the ASES Installation-8-2 – 24 bucs. - Convenient access to the cells of the drying chamber: On the front side of the cabinet there are four doors for access to the cells. - Natural ventilation: The absence of rotating elements ensures absolute noiselessness of operation and a long service life. - Built-in timer: The ASESH-8-2 installation has 4 timers, by means of which the end of the drying process is monitored in each section with the output of an audible signal and a light indication. - The output to the operating mode is 30 minutes: The power of air-thermal installations is 1200 watts. When entering the operating mode, the power consumption is the same as that of similar cabinets with low power. SCOPE OF DELIVERY : 1. Installation of ASESH-8-2 2. AO-3 cooler 3. Auxiliary accessories 4. Air-heat control unit: 5. Interface unit for connecting a personal computer with a scale (available on request); 6. software for processing and archiving measurements of humidity determination data; The program allows you to: Set the operating temperature in the chambers via a personal computer Set the necessary parameters of the sample drying process according to the selected method Display all current processes (predrying, drying, cooling) and parameters (temperature, time) during the tests. To monitor the process by means of an electronic timer with the output of an audible signal. Record all weighing results. Perform humidity calculations in accordance with standardized methods. To calculate the humidity with pre-drying, the program uses formulas that allow you to get an accurate result. Archive and print test results. According to the test results of FSUE "UNIIM", it is recommended to use a laboratory mill of the BLIZZARD series for sample preparation. SCOPE OF APPLICATION: 1. Crop production, agriculture and forestry. 2. Products of meat, dairy, fish, flour-milling, feed and microbiological industries. 3. Food industry products. 4. Cellulose, paper, cardboard and products made from them. 5. Medicines, chemical and pharmaceutical products and medical products. 6. Building materials. 7. Products of the logging and sawmilling and woodworking industry. 8. Ground, soils, mineral fertilizers. Technical specifications: The measurement range of the mass fraction of moisture, % from 0.5 to 80 Operating temperature range, °C from 45 to 160 The error of setting and maintaining the temperature in the working area, ° C, not more than 2.0 Limits of permissible absolute error, % ± 0.5 Power consumption, V• A, not more than 1200 Overall dimensions, mm 240 × 260 × 640 Overall dimensions of the cell, mm 75 x 40 x 165 (depth) Weight, kg 28.4

DPSS lasers of the KLM-593/x series are diode-pumped solid-state lasers of the visible spectral range (593 nm) with collimated continuous radiation of low and high power (depending on the model). The package includes: a laser head, a power supply, a set of connecting wires, a power cable and a device passport. Depending on the tasks, the following options are available for each laser model: the presence of TTL modulation / the presence of analog modulation, power control via the power supply, the presence of a display for the power supply, improved power instability (<3% / <1%), improved temporary power instability (4 h / 8 h), radiation sweep in-line (5...120°), laser head with fiber output (FC/SMA), extended warranty period, custom housing development. These lasers are widely used in medical equipment, for control and automation of technological processes, in scientific research, astronomy, spectroscopy. They are optimal sources of coherent radiation for the construction of systems of alignment and marking devices.

The Kjeldahl method is one of the most accurate methods for determining nitrogen and protein in a wide group of products, but, unfortunately, it has a number of significant drawbacks - these are low speed, a large number of possible losses during the analysis, bulky equipment, and the use of aggressive reagents. Sibagropribor Holding presents KELTRUN (KELTRUN) - a set of equipment for carrying out a complete analytical cycle according to the Kjeldahl method, which will allow: • to increase the speed of analyzes (high speed of distillation and ashing, simultaneous processing of several samples); • ensure the safety of personnel (high quality of reaction vessels, effective absorption of acid vapors by the exhaust system, additional protection of personnel in emergency situations); • reduce possible losses in the analysis process; • improve the reproducibility of results. «KELTRAN» (KELTRUN) will allow you to determine nitrogen / protein in the widest list of substances: • food products: dairy, cereals, meat, cereals, etc.; • feed and compound feed; • fertilizers; • water, drinks, beer; • soil, bottom sediments, sediment samples, activated sludge; • crude oil, lubricants; • various chemicals; • alcohol content in wines, musts and spirits; • etc. The set of equipment «KELTRAN» (KELTRUN) allows you to analyze according to GOST and determine the nitrogen content in the range of 0.02 - 99.00%. Composition of the complex «KELTRAN» (KELTRUN): - Digestor; - Distiller; - Scrubber (*not included in the price of the complex); - Titration unit: manual, semi-automatic or automatic (*not included in the price of the complex); Warranty - 1 year. Important feature! In many distillers (made in China and others), when used, alkali passes through a valve-type pump, with a low production resource (sometimes the resource is enough for only 3 months). In the distiller of our production, the alkali passes through a RELIABLE PERISTALTIC PUMP, this ensures a long service life of the distiller! Package options Cost (including VAT): Digestor, Distiller, Water jet pump 379,400 rubles; Digestor, Distiller, Water jet pump, Scrubber 434,700 rubles; Digestor, Distiller, Water jet pump, Manual titration unit 396,900 rubles; Digestor, Distiller, Water jet pump, Scrubber, Manual titration unit 452,200 rubles; Digestor, Distiller, Water jet pump, Kit «Titrion-pH» (c2) 605,400 rubles; Digestor, Distiller, Water jet pump, Scrubber, «Titrion-pH» kit (c2) 660,700 rubles.

Checking the performance of cardiographs, cardiac monitors and cardiac units of intensive care monitors; checking the general functionality and imitation of the patient (when checking stress systems, a cardioid signal is formed); checking the amplitude of the signal recording (a U-shaped signal is formed).

Capacity, m3/h 100 Bactericidal efficiency, % 99.9 Total power of ultraviolet radiation of bactericidal lamps, W, not less 14.4 Service life of UV lamps, hours 9000 Power consumption, W, 62±10 Adjusted sound power level, no more than 40 dBA Bactericidal UV light lamp LUV 15W, with a power of 15W 3 pcs Dimensions (H*W*D), mm 886*366*163 Weight, kg, no more 7 Warranty, years 2 Approximate dimensions of the product with packaging Net weight of the product, kg 7 Gross weight of the product, kg 7,8 Volume of packaging, m3 0.068 Length of the package, m 0.92 Width of the package, m 0,41 The height of the package, m 0.18

• OKP code 94 4370 • The color of the box is resistant to treatment with desolutions.  • Number of filtration degrees: 1 or 2 • Pre-filter class according to GOST R 51251-99: G4 • HEPA filter class according to GOST R 51251-99: N14 • The degree of purification of the emitted air from suspended particles larger than 0.2 microns: 99.995% • Air purity class of the working area according to GOST R ISO 14644-1-2002 (by particles 0.5 microns): 5ISO • Protection class (according to WHO classification): IIA • Total air capacity: 1350 m3/h  • Capacity for air entering the working chamber of the box: adjustable, from 400 to 900 m3/h • Recycling rate: 80% • The air flow rate in the working area is adjustable: from 0.2 to 0.45 m/s • The internal chamber of high pressure is surrounded on all sides by zones of low pressure relative to atmospheric • Power of the UV lamp of the working chamber: 30 W • Sound power level of the laminar box: no more than 57 dBA • Illumination of the working area of the laminar box: at least 1000 Lux • Shadowless lighting of the working area of the laminar box • Suspended front window with lifting and stopping at any level • The control panel is located outside the working area, which provides easy access during repairs and no contact with potentially dangerous agents in the duct system and air purification • Sockets in the work area: 2 pcs • Power consumption: 210W • Weight of the box: no more than 120 kg • Dimensions of the working chamber of the laminar box (WxDxH): 1160x570x630 mm • External dimensions of the laminar box (WxDxH): 1200x670x1270 mm • Equipped with a stand table • Dimensions of the stand (WxDxH): 1200x670x650 mm • Continuous operation time is unlimited • Warranty period: 18 months from the date of delivery and acceptance of the product • Package dimensions (WxDxH): 1290x780x1370 mm

• The frozen product is placed in the dryer in stainless steel trays, or in separate containers with a flat bottom up to 105 mm high (test tubes, ampoules, vials, vials, cones, Petri dishes, glass laboratory glasses, etc.). A low-temperature chamber must be provided for freezing the product.  • Drying speed of at least 100 g/h.  • Additional devices: - manifold with vacuum taps for drying from flasks; - centrifuge for drying in ampoules; - collector with taps for sealing ampoules in vacuum; - low temperature trap; • The temperature of the condenser is -50 °C (5 ° C), the capacity is 6 kg of ice.  • The working pressure in the vacuum chamber of the dryer is 6.67 Pa (5•10-2 mmHg), a vacuum pump with a gas ballast device.  • Adjustable shelf temperature from -15°C to +45°C. • Monitoring of vacuum parameters and temperature of the condenser and the product. • Continuous operation time of at least 30 hours. • The dryer is powered by a three-phase 380 V AC mains. The power consumption is 1.3 kW. • External dimensions: 590x660x820 mm, weight 120 kg.

Devices capable of generating oxygen have found the widest application in various fields of medicine. The equipment is also used in training centers, educational institutions and oxygen rooms. Medical oxygen concentrators make it possible to accelerate the recovery of patients suffering from cardiovascular diseases, chronic respiratory diseases, as well as other pathologies that make it difficult to saturate the blood with oxygen. This equipment is a mandatory equipment for anesthesiology and intensive care units. Oxygen concentrators demonstrate high efficiency in restorative treatment. Unlike oxygen sources, which use compressed gas, generators are characterized by high safety and efficiency Capacity: 500-600 l/min 34.8-36.0 m3/h 46.4-47.8 kg/h Oxygen purity: 95 % Oxygen pressure: 4-5 bar

Technical characteristics: Consumption of working reagents 1.0–2.0 ml – for standard filling cuvette K10 from 400 ml – for photometric techniques Filters for photometer mode, nm built-in interference filters 340, 405, 505 ,545, 575, 630 spectral half-width of 10 nm Filters for fluorimeter and chemiluminometer modes on request, in the spectral range of 270-850 nm Chemiluminescence channel sensitivity 10000 photons per second Optical density measurement range, E.O.P. 0-2.20 Photometric channel accuracy, %2 Memory of 100 measurement programs Temperature control of the measuring cell (for photometer and chemiluminometer modes) built-in thermostat on the Peltier element: 25, 30, 37 OC; accuracy ± 0.2 oC Volume of the flow cuvette, mkl 80 Pump type (only for photometer mode) peristaltic pump with programmable liquid supply volume Productivity, analyses/hour up to 100 (by the endpoint method) Information output liquid crystal display and personal computer Power supply, 220 ± 22 Dimensions, mm 430x350x160 Weight, kg 10

Devices capable of generating oxygen have found application in various fields of medicine. The equipment is also used in training centers, educational institutions and oxygen rooms. Medical oxygen concentrators allow to accelerate the recovery of patients suffering from cardiovascular diseases, chronic respiratory diseases, as well as other pathologies that make it difficult to saturate the blood with oxygen. The concentrator is a mandatory equipment of the departments of anesthesiology and intensive care. Oxygen concentrators demonstrate high efficiency in restorative treatment. Unlike oxygen sources that use compressed gas, generators are safe and economical. Capacity: 140 l/min 8.4 m3/h 11.2 kg/h Oxygen purity: 95 % Oxygen pressure: 4-5 bar

DPSS lasers of the KLM-556/x series are optimal sources of coherent radiation for the construction of control and automation systems, alignment and marking devices, for scientific and medical purposes.