Accessories

The tank for the 1.5 kW aquadistillator is made of stainless steel.

Partially universal detector. It is used for the analysis of most organic compounds, including aromatic and aliphatic (except methane) hydrocarbons, heterocyclic compounds, phenols, phthalates, pesticides, amines, ketones, aldehydes, esters, mercaptans. It does not register compounds whose ionization threshold is higher than 10.2 eV (for example, acetonitrile, methanol). Technical characteristic: 5.0*10`13 g/s for benzene

The stand provides convenience when taking measurements, allowing you to set the thermometers at eye level. It is designed for calibration thermostat THERMOTEST 300. Overall dimensions 400x625x420 mm

The metering valve for the introduction of gas samples is designed for the introduction of gas under excessive pressure into the chromatograph. Cranes differ in the number of moves (4, 6, 8, 10, 12) and have two provisions "Selection" — "Analysis". In addition to dosing, cranes can be used to switch chromatographic columns, elements of gas circuits, etc. The tap can be installed either on the side panel of the chromatograph, or directly into the analytical module instead of, or together with the evaporator of the chromatograph, while it is used as a back-purge tap or for hot sample entry. Additionally, the tap for hot entry can be equipped with heated pipelines. technical specifications The dose volume is from 0.25 to 5.0 ml (at the request of the consumer, the dose volume can be increased to 10 ml and reduced to 0.1 ml). The maximum temperature of the tap is no more than 160 °C. The pressure in the crane line is not more than 0.48 MPa. The angle of rotation of the crane handle — depending on the number of strokes.

Eight holes with a diameter of 17 mm will serve to accommodate glass tubes, the remaining nine ventilation holes — for better convection of the coolant. Internal dimensions 240x120x210 mm Weight 1 kg

Technical specifications Material: S-TIH53 (Ohara) Length, mm: 5 Height, mm: 1.5±0.02 Thickness, mm: 1.5±0.01 Refractive index, mm: 1.823 Effective focal length, mm: 0.91 Rear focal length, mm: 0.09 Transmission, %: >99.5 Power within the angle ± 0.7 mrad, %: >85 Antireflection coating, nm at one of the wavelengths from the range: 400-1500 Numerical aperture: 0.8 Surface quality λ = 633, nm: λ/4

Basic properties Low bandwidth losses; A wide barrage strip. Operating conditions Operating temperature range from minus 10 up to 50 ° C; The relative humidity of the air is up to 98% at a temperature of 25 ° C. Technical specifications Waveguide cross section, mm 5.2×2.6 Bandwidth Fh-Fb at the level of -1 dB, GHz 37-45 The barrage band at the level of -30 dB, GHz 50-70 Bandwidth loss, 0.5-1.0 dB

Number of sockets, pcs 27 Hole diameter, mm 22 Immersion depth, mm 150 Overall dimensions (WxDxH), mm 235x80x165

It is designed for the devices KFK–2, KFK–3 and their modifications when operating in the spectral range from 315 to 980 nm. It is chemically resistant to acids (except hydrofluoric acid) and dilute alkalis.

Designed for immersion of objects in the baths of LOIP LT thermostats and LOIP LB-200 precision thermostatic baths to a predetermined depth. Thermostatable objects are placed on a movable pallet, which can be fixed at any required depth. The device is installed on the casing of thermostats and precision thermostatic baths instead of a hinged lid and is equipped with its own removable lid. Bath volume, l 17 and 24 Pallet size, mm 260x320 Maximum immersion depth, mm 200

The video camera and servos of the electrode holders built into the tripod are designed to automatically maintain the interelectrode gap during the evaporation of the sample by computer analysis in real time of the image of the arc discharge, as well as the initial setting of this gap relative to the optical axis. The electrode holders are cooled with water using a closed-cycle cooling unit.