Equipment

The nitrogen generator is designed to create an inert atmosphere, fill low-pressure tanks, "wash" test tubes with inert gas and other applications that require a large, by laboratory standards, nitrogen consumption with reduced requirements for its purity. Technical specifications Volume fraction of nitrogen is not less than 99.0 % by volume (including impurities of inert gases — argon, neon, helium) Volume fraction of oxygen is not more than, 1.0 % vol. Volume fraction of water vapor is not more than 0.002 % vol. (20 ppm) Maximum nitrogen capacity: at an inlet air pressure of 7 ati is at least 1380 l/h (23 l/min) The time of setting the operating mode for single-shift operation is no more than 30 min Minimum inlet air pressure is 7 ati Maximum allowable inlet air pressure is 8.5 ati Compressed air consumption, at nominal inlet pressure and maximum flow rate is no more than 150 l/min Power consumption is not more than 200 VA Overall dimensions, (width x depth x height) are not more than 230x580x680 mm Weight is not more than 38 kg Working conditions: ambient temperature, C°, from +10 to +35 Electric power supply from single-phase AC mains voltage, V, 220± 10% and frequency, Hz, 50 ± 1 Average full service life is at least 6 years The generator for electrical safety meets the requirements of Class 1, type H according to GOST 12.2.025-76

The working fluid of the pump is water. These pumps are designed to work with liquids as well as gases and vapors slightly soluble in them that are not aggressive to the materials of the 2VVN1-3M pump design, not explosive and non-toxic. The use of a 2VVN1-3M(H) water-ring vacuum pump for pumping out water-gas mixtures is allowed only if the bulk of the water is separated and discharged at the pump entrance. Failure to comply with this requirement may lead to unacceptable overload of the electric motor and destruction of the working bodies of the 2VVN1-3M(H) pump. The vacuum water ring pump 2VVN1-3M (H) is manufactured in the climatic version of UHL (i.e. for moderate and cold climate) 4 and O4 according to the GOST standard 15150-69, meets the requirements of technical specifications TU 3648-015-00218526-2000, designed and manufactured taking into account the requirements of GOST R 52615-2006. Electricity grid must meet the requrimemnts of GOST 32144-2013

Design features: Durable ceramic muffle; Closed heaters on four sides of the chamber; Microprocessor temperature controller; Conveniently located control panel and bright LED display; Ease of management and control; LED indicators of heater operation and protection operation; Automatic shutdown of heating when opening the door; The door opens up and faces the user with the cold side; Alarm when the current temperature exceeds the limits of the permissible range; Highly efficient thermal insulation of the housing; The furnace body is made of high-quality sheet steel and painted with heat-resistant powder paint. Technical specifications: Maximum heating temperature, °C +1100 Temperature stability in steady-state thermal mode, °C ± 10 Warm-up time to the maximum temperature, no more than 120 min Dimensions of the working chamber, WxHxD, not less than mm 215x190x330 Overall dimensions, WxHxD, not more than mm 525x655x680 Rated supply voltage, 220 V Rated power, W 6000

The sand bath "PB" I2T with digital control and a heating area of 260x510 mm. is designed for heat treatment of samples, evaporation and laboratory analysis. The product is equipped with a shutdown timer.

Catalytic reforming is used to produce high-octane components of automobile gasoline, flavored concentrate for the production of individual aromatic hydrocarbons, as well as technical water. Isomerization of paraffin hydrocarbons is used to increase the octane number of C5 - C6 oil fractions by converting paraffins of normal structure into their isomers having a higher octane number.oroda. Hydrotreating of distillates is used to improve the quality and stability of light distillates, raw materials of catalytic cracking, as a result of the use of reactions of destructive hydrogenation of organosulfur compounds and hydrogenation of unsaturated hydrocarbons. Catalytic cracking is used to obtain additional amounts of light petroleum products, namely high-octane gasoline and diesel fuel, by decomposition of heavy oil fractions in the presence of a catalyst. Alkylation of isobutane with olefins is used to produce gasoline fractions with high stability and detonation resistance using the reaction of interaction of isobutane with olefins in the presence of a catalyst. Polymerization (oligomerization) of olefins is used to produce low molecular weight polymers (oligomers) of propylene and butylene used as motor fuel or raw materials for petrochemical synthesis. Hydrocracking is used to obtain an additional amount of light petroleum products by catalytic decomposition of heavy raw materials in the presence of hydrogen. Thermal cracking and Visbreaking is used to obtain in the mode of thermal cracking – additional amounts of light petroleum products by thermal decomposition of residues from oil distillation, in the mode of visbreaking – improving the quality of boiler fuel Coking is used to produce petroleum coke and an additional amount of light petroleum products from heavy residues. The raw materials are tar, thermal cracking residue, heavy gas oil. The products are, for example, petroleum coke.

It is designed to maintain temperature when determining the kinematic viscosity of petroleum products with glass viscometers in accordance with GOST 33, GOST R 53708, ASTM D445, IP 71, ISO 3104 and DIN 51366 and when determining the pour point of petroleum products in accordance with GOST 20287. Operating temperature range -30...+50 °C Four places for glass viscometers or a basket for determining the pour point of petroleum products. Stability and uniformity of temperature in the working bath is not worse than ± 0.01 ° C. Bath volume 15 l Overall dimensions 440x710x620 mm The open part of the bath is 140x170 mm Bath depth 320 mm The size of the viewing window is 104x270 mm Weight 56 kg Power consumption 3.5 kW

For vacuum dewatering of pre-frozen substances with condensation of evaporated moisture on a low-temperature condenser, the company "Prointech" offers a new FREEZE DRYER LS-1000. (RF Patent No. 2213916 of 06/18/2011) Characteristic features - the shortest trajectory of vapors - visual inspection of the product - minimum volume to achieve rapid pumping to vacuum - sterilizable stainless steel chamber - compactness, lightness

The stability and uniformity of the temperature in the working bath is not worse than ± 0.01 ° C. Bath volume 15 l Overall dimensions 790x500x1180 mm The open part of the bath is 125x190 mm Bath depth 250 mm Weight 119 kg Power consumption 4.2 kW

Maximum heating temperature, °C 400 Temperature difference across the platform, °C, not more than ± 5 Dimensions of the heating platform, mm 435x315 Power consumption, W 2500 Platform material aluminum alloy Overall dimensions, mm 470x453x110 Weight, kg 15

The PL.HM03.01.60 Primelab vacuum diaphragm pump is suitable for creating a vacuum up to 60 mbar and a flow rate of 38 l/min. It has a dry design that does not require lubrication. Quite easy to use and does not create any inconvenience during operation. Its noise level does not exceed 75 dB. With a light weight of 6.9 kg, it has compact dimensions (289.5x160x200 mm), allowing the pump to be integrated into an already equipped space. Complies with IP20 protection class. The PL.HM03.01.60 Primelab vacuum diaphragm pump is supplied in the following package: vacuum pump, cable, instructions, passport, packaging (vacuum regulator and spare parts are not included in the kit and must be ordered separately). Warranty and post-warranty service is available in Russia.

A trace searching kit for finding underground utilities (cable lines, metal pipelines, and other communications made of conductive materials). The kit includes a receiver in the form of a monoblock with a frost-resistant LCD display, which displays an image of the route and automatically calculates the depth of communication up to 10 m, as well as the current in the line and the most powerful multi-frequency generator in the TECHNO-AC line, with a range of up to 10 km.