NV-800 MD-B Wash table without dryer (850×800×600)

A table with an overall height of 900 mm with a countertop measuring 900 × 640 mm made of porcelain stoneware, monolithic ceramics or stainless steel. It is designed for long-term operation, the power frame does not contain aluminum and plastic parts in the fasteners. Overall dimensions without superstructure 900x640x900 mm

The NV-1500 SM is a specialized table for microscopy. The table top is 70 cm deep and is made of laminate. It is designed for sitting work: the height from the floor to the countertop is 75 cm (this is the height of a regular office desk). External dimensions of the table (W×D×H): 1500×700×750 mm. A small superstructure allows you to compactly place the necessary drugs and accessories next to the workplace. Its dimensions: (W×D×C): 668×120×200 mm. The table top is made of laminated chipboard. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents and is well suited for the placement of devices. The side laminated panels of the table (chipboard 16 mm thick) are edged with a PVC edge 2 mm thick, which increases their impact resistance and mechanical strength. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor.

Laboratory work desk Table top: KG (porcelain stoneware) Length, mm: 900 Depth, mm: 650 Height, mm: 900 BASIC EQUIPMENT The base is a collapsible frame made of rectangular steel profile, painted with powder paint (RAL 7035) with the texture of shagreen leather Hidden fasteners Two easily removable rear screens (RAL 7035) and one non-removable (RAL 5023) Adjustable supports (0-40 mm)

The Kors NV-1500 SHVD-U laboratory fume cupboard is a two—frame cabinet with a granite countertop with a width of 1410 mm and a small built-in sink made of polypropylene. External dimensions of the cabinet (W×D×H): 1410×700×1960 mm. Dimensions of the working area (W×D×H): 1378×540×750 mm. Table top: granite tiles. Working surface material: porcelain tile. It is moisture-resistant and perfectly withstands high temperatures. It is resistant to prolonged exposure to concentrated acids, alkalis and organic solvents. Limited resistance to hydrofluoric acid. This is one of the most popular types of countertops for laboratory furniture. The small sink-drain is made of polypropylene, resistant to aggressive chemicals. Its diameter is 135 mm and its depth is 110 mm. The working area is closed by two lifting frames with a counterweight. As standard, there are two exhaust zones: the hood of the exhaust box and the level of the countertop. Diameter of the flange for connection to the ventilation system: 150 mm. Working area size (W×D×H): 1378×540×750 mm. Please note that the cabinet narrows upwards. At a height of 50 cm, the depth of the working area will be 410 mm, at a height of 70 cm: 365 mm. If you need to place high equipment, then make sure that it corresponds to the dimensions of the camera, otherwise you will not be able to close the cabinet. The height of the raised glass above the cabinet: 510 mm, that is, when the glass is raised, the height of the cabinet will be 2470 mm. The NV-1500 SHVD-U fume cupboard is equipped with an LED lamp with a switch and two sockets, one of them with grounding. Sockets have the IP20 degree of protection, the maximum load on them: 1.5 kW. The working chamber is an all-welded metal frame in powder coating. Load-bearing laminated panels (chipboard with a thickness of 16 mm) are edged on the facade with a durable PVC edge with a thickness of 2 mm, which increases the impact resistance and mechanical strength of the products. The cabinet legs are adjustable in height within two centimeters, allowing you to place the cabinet even on a rather uneven floor.

900 mm wide, 2025 mm high cabinet made of painted steel for storing laboratory utensils and documents. Two compartments with two metal shelves in each. The upper doors are made of glass, the lower ones are made of steel. Overall dimensions 900x500x2025 mm Weight 95 kg

BASIC EQUIPMENT Working box guide posts – aluminum profile painted with powder paint (RAL 7035/RAL 5023) in the right rack there is a light switch front anti–spill side - acid-resistant polished stainless steel AISI 304 side panels – tempered glass 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-780mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – metal painted with powder paint (RAL 5023) with the texture of shagreen leather back and top panels – polypropylene on the top panel: LED lamp dust- and moisture-proof 22W IP65 switching box with automatic emergency shutdown power supply 16A flange d=250mm (the distance from the back panel to the center of the flange is 170mm) easily removable exhaust canopies 3 exhaust levels (lower, side and front) counterweights are placed in the front pylon racks and are easily serviced Frame base metal pedestal painted with powder paint (RAL 7035) with the texture of shagreen leather facades – laminated MDF with a thickness of 16mm handles – polypropylene 2 compartments with locks 1 shelf with the possibility of installation on three levels in any of the compartments (when the cabinet is equipped with 2 bowls, shelves are not included) flange d=100mm service panel – aluminum profile painted with powder paint (RAL 5023) with the texture of shagreen leather: adjustable supports

The table top is a single module made of stainless steel SUS 201 (analog AISI 201) ATTENTION! The product is recommended to be used only for work with non-aggressive substances. inner bowl size – 340*400* 130mm cabinet body – melamine 16mm thick

Furniture for laboratory work. The mezzanine is low to the storage cabinets Length, mm: 800 Depth, mm: 500 Height, mm: 1940 PACKAGE CONTENTS housing – white melamine with a thickness of 16 mm facades – white melamine, ABS edge dark gray 1 compartment without shelf without locks handles-brackets dark gray 128 mm, polypropylene.

NV-1500 O is an island table with a superstructure that can be placed in the center of the laboratory and organize workplaces on its two sides. Table top depth: 152 cm. It is designed for standing work: the height from the floor to the table top is 85 cm. A lamp and two sockets are built into the superstructure on each side. External dimensions of the table (W×D×H): 1520×1520×1650 mm. Work surface for your tasks We offer tables with various work surfaces. Table Model: Tabletop NV-1500 OL: Laminate. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. NV-1500 OK: Porcelain tile. It is a practical solution for most chemical, biological, medical laboratories and workshops. You can put drying cabinets, baths and other heating devices on it. NV-1500 OSB: Chemically resistant plastic. It is a good choice for training workshops, analytical and medical laboratories. It does not tolerate high temperatures well, heating devices should not be placed on the surface. NV-1500 OP: Polypropylene. It is chemically resistant, being a specialized solution for chemical laboratories that work a lot with concentrated inorganic acids and alkalis. It is not resistant to high temperatures. A table for convenient work in the laboratory The superstructure allows you to compactly place the necessary reagents and laboratory utensils next to the workplace. Its depth is 30 cm, and its height is 80 cm. The working area on each side is illuminated by a fluorescent lamp (included in the package). The switch is located on the left-hand side of the superstructure. There are also two sockets, one of which is grounded. Sockets (with two on each side, there are four of them in total) have the IP20 degree of protection, maximum load: 1.5 kW. Two cabinets are built into the table on each side, one with a hinged door and a shelf inside, the other with three pull-out drawers. You can store there laboratory utensils or small stuss you need at hand. The side laminated panels of the table (chipboard 16 mm thick) are edged on the facade with a 2 mm PVC edge, which increases their impact resistance and mechanical strength. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rather uneven floor.

The complete set is fully made of polypropylene. There are no components sensitive to the action of corrosive substances. Inside the storage area there are 2 compartments.In each compartment there is 1 easily removable shelf made of polypropylene with the possibility of installation at 3 levels in heightThe permissible load on the shelf is 30 kg. The storage cabinet also includes: 2 hinged facades made of polypropylene hinges outside the storage area (pin system) polyamide lock in each door handles made of polypropylene cabinet has a double back wall. Extraction of reagent vapors is carried out from all storage areas flange ∅ 100 mm on the back wall for connection to the exhaust ventilation hidden adjustable supports (0-40 mm). The adjustment of the supports is carried out from inside the pedestal through the base

Furniture for laboratory work. All-metal exhaust cabinet Working surface: FRIDURIT (20 mm) Overall dimensions: Length, mm: 1800 Depth, mm: 740 Height, mm: 2100 equipment Working box anti–spill side – acid–resistant polished stainless steel AISI 316 housing - metal painted with white powder paint (RAL 9016) guide posts – aluminum profile painted with dark gray powder paint (RAL 7011) 2 dependent lifting screens - tempered glass in aluminum frames, lifting 0-710mm, not change the dimensions of the cabinet when lifting.

The table is 760 mm high with a countertop measuring 1800×800 mm made of porcelain stoneware, monolithic ceramics, stainless steel, chipboard or plastic. It is designed for sitting work. It can be equipped with various superstructures, sliding and hanging bollards. Overall dimensions 1800x800x760 mm

Island table Table top: LAMINAT (table top consists of 2 cohesive parts, the seam is treated with moisture-resistant glue) Length, mm: 1800 Depth, mm: 1500 Height, mm: 900 BASIC EQUIPMENT The base is a collapsible metal frame made of rectangular steel profile, painted with powder paint (RAL 7035) with the texture of shagreen leather Four easily removable screens (RAL 7035) and two non-removable (RAL 5023) Hidden fasteners Adjustable supports (0-40 mm) A set of end boxes-plugs

Working surface: Porcelain stoneware (ceramic tile 300*300mm) Length, mm: 832 Depth, mm: 925 Height, mm: 2100 equipment Working box the side and back panels are lined with a row of ceramic tiles to a height of 400mm the case is melamine with a thickness of 16mm lifting screen with the possibility of fixing at any height – organic acrylic glass with a thickness of 8mm, lifting 0–750mm, increases the height of the cabinet with a full lift by 430mm

BASIC EQUIPMENT Working box the front guide posts are aluminum profile painted with powder paint (RAL 7035/RAL 5023), in the right rack there are a light switch and 2 splash–proof sockets with a 3.2kW cover (IP54) the front anti–spill side is acid-resistant polished stainless steel. AISI 304 steel rear, upper, side panels – metal painted with powder paint (RAL 7035) with the texture of shagreen leather the inner surfaces of the working box are lined with chemically resistant HPL plastic 2 dependent lifting screens – tempered glass in aluminum frames, lifting 0-780mm, do not change the dimensions of the cabinet when lifting the upper fixed screen – tempered glass in an aluminum frame on the upper panel: LED dust- and moisture-proof lamp (2X10W IP65) is separated from the workspace by tempered glass thickness of 4mm flange d=250mm (distance from the rear panel to flange center – 170mm) easily removable exhaust canopies 3 exhaust levels on the left side panel service module with cold water supply pipe and wall-mounted drain sink made of polypropylene cold water supply valve in the left rack of the box counterweights are placed in the front racks-pylons and are easily serviced Frame base collapsible frame made of rectangular metal profile painted with powder paint (RAL 7035) with the texture of shagreen leather service panel - aluminum profile painted with powder paint (RAL 7035/RAL 5023) with the texture of shagreen leather adjustable supports module with two drawers

Furniture for laboratory work. Mobile table Working surface: TRESPA TopLab 6mm, on a substrate of wood-containing material (plywood 15mm, melamine 16mm), edged around the perimeter of PVC edge 2mm. Length, mm: 800 Depth, mm: 600 Height, mm: 800 The complete set of the shelf at a distance of 250mm from the floor is melamine with a thickness of 16mm all–welded frame made of a rectangular metal profile painted with white powder paint roller supports h = 60mm (without stopper)

Furniture for laboratory work. Laboratory table Working surface: TRESPA TopLab 6mm, on a substrate of wood-containing material (plywood 15mm, melamine 16mm), edged around the perimeter of PVC edge 2mm. Length, mm: 1600 Depth, mm: 600 Height, mm: 900(1800) EQUIPMENT rack support racks – aluminum profile painted with powder paint (RAL 1001) the top panel of the rack with a depth of 190mm – metal painted with powder paint (RAL 1001)