Search

Island table Combined working surface: STEEL main table top (single stainless steel module with anti-spill side) with a depth of 650 mm / auxiliary table top made of TRESPA material with a depth of 200 mm / STEEL main table top with a depth of 650 mm Length, mm: 900 Depth, mm: 1500 Height, mm: 900 BASIC EQUIPMENT The base is a collapsible metal frame made of rectangular steel profile, painted with powder paint (RAL 7035) with the texture of shagreen leather Four easily removable screens (RAL 7035) and two non-removable (RAL 5023) Hidden fasteners Adjustable supports (0-40 mm) A set of end boxes-plugs

Furniture for laboratory work. Titration table Working surface: Porcelain stoneware (the surface directly under the rack is TRESPA Athlon 8mm) Length, mm: 1600 Depth, mm: 600 Height, mm: 900(1800) EQUIPMENT rack support racks – aluminum profile painted with powder paint (RAL 1001) the top panel of the rack with a depth of 190mm – metal painted with powder paint (RAL 1001)

The working condition of the ND-630 diffusion pump depends on the temperature of the working fluid in the pump boiler. During the initial filling, it is recommended to fill the maximum volume of the working fluid. Working fluid is "VACMA OIL 500" vacuum oil (uner technical specifications TU 19.20.29-061-00218526-2019). The total amount of working fluid in the ND-630 diffusion pump is a maximum of 9 liters, a minimum of 6 liters. The viewing window for visual inspection of the working fluid has marks of its maximum and minimum amounts. During normal operation of the pump, the level of the working fluid practically does not change. The temperature of the working fluid when the pump is operating at the maximum residual pressure is about 240°C to 255°C. It is recommended to monitor the operation of heaters in the ND-630 diffusion pump using one temperature sensor. The temperature sensor must be installed in a special radiator socket above the heater. If there is a loss of working fluid and an increase in the temperature of the radiators of the ND-630 diffusion pump up to 360°C, the temperature sensor must give the command to automatically turn off the heaters. The subsequent activation of the pump heaters should not be automatic and should be performed only after cooling the system. Water at the inlet to the cooling systems of the housing and the oil reflector must be supplied with a pressure of 0.3 MPa (3 kgf/cm2) to 0.5 MPa (5 kgf/cm2) and a temperature of plus 4°C to plus 25°C. The recommended cooling water consumption for the housing is 600 l/h, for the oil reflector it is 80 l / h. It is regulated by the outlet water temperature, which should not exceed plus 40°C. The water drain should be free (with a jet break).

Furniture for laboratory work. Table-sink LAB-M MO 120.65.90 TF Width, mm: 1200 Depth, mm: 650 Height, mm: 900 Equipment: Table top – TRESPA TopLabPlus is a monolithic slab of ultra–high pressing thickness of 6mm with a chemically resistant surface made of polyurethane-acrylic composition, on a substrate of wood-containing material (plywood 15mm or melamine 16mm), edged around the perimeter with a PVC edge of 2mm 1 built–in bowl - FRIDURIT ceramics. The location of the bowl in the center, fixing the bowl flush with the level of the countertop. Inner bowl size – 400*400*250 mm The base of the sink table is a support pedestal made of white melamine Facades – laminated MDF of white color with a thickness of 16 mm, dark gray ABS edging Without shelves

The LOIP LT-416b modification device consists of an immersion thermostat-circulator LOIP LT-400 and a working bath with a lean-to hinged lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +200 with tap water cooling °C Tvods+5 ...+200 Accuracy of temperature maintenance, °C ± 0.01 The error of setting the set temperature, no more than, ° C ± 0.02 Heater power, W 2200 Pump: max. flow rate, l/min 6...12 pressure, 0.4 bar Bath volume, l 16 The working fluid is water, silicone oil. Open part of the bath / depth, mm 190x296/200 Overall dimensions, mm 355x335x400 Weight, kg 12.9

Purpose: obtaining distilled water of 3 types according to GOST R 58144-2018 "Distilled water", FS.2.2.0020.18 "Purified water" Capacity: 140.0 (-10%) l/h Heating elements: electrodes The quality of the produced water GOST R 58144-2018 "Distilled water", FS.2.2.0020.18 "Purified water" Type of current, frequency, voltage: alternating three-phase, 50 Hz, 380 V Power consumption: 84.0 kW Overall dimensions (L×W×C), mm: 810×630×1420 Weight: 87 kg Warranty period: 12 months from the date of sale Registration certificate for a medical device No. FSR 2008/03707 dated December 05 , 2008 Electrical conductivity of the produced water: 3-4.5 microns/cm Produced water temperature: 50 °C Source water flow rate (at 10 °C water temperature): 1000 (+-10%) l/h Source water pressure: 01,-0.4 MPa Overall dimensions of the control unit (L×W×C), mm: 400×220×500 Execution: outdoor Coefficient of water purification from radionuclides: at least 4000 Service life: at least 8 years

The stand provides convenience when taking measurements, allowing you to set the thermometers at eye level. Designed for calibration thermostat THERMOTEST-100. Overall dimensions 400x625x490 mm

BASIC EQUIPMENT The base is a collapsible frame made of rectangular steel profile, painted with powder paint (RAL 7035) with the texture of shagreen leather Hidden fasteners Two easily removable rear screens (RAL 7035) and one non-removable (RAL 5023) Adjustable supports (0-40 mm)

Furniture for laboratory work. Table-sink on a support pedestal made of metal LAB-M MO ME 150.65.90 PP Width: 1500 Depth: 650 Height: 900 equipment: Table top – polypropylene with an overhead rim around the perimeter Attention! It is not recommended to use it for work with oil and petroleum products (fuel oil, bitumen, etc.) The bowl is polypropylene. The location of the bowl in the center, the mounting of the bowl is suspended. Inner bowl size – 400*400*300 mm The base of the sink table is a metal support pedestal. All-welded frame painted with dark grey powder paint RAL 7011. The bottom and top of the housing are sheet steel painted with powder paint of dark gray RAL 7011, the side walls are made of sheet steel painted with powder paint of white RAL 9016. Facades – laminated MDF of white color with a thickness of 16 mm, dark gray ABS edging

Laboratory work desk Table top: KG (porcelain stoneware) Length, mm: 1800 Depth, mm: 650 Height, mm: 750 BASIC EQUIPMENT The base is a collapsible frame made of rectangular steel profile, painted with powder paint (RAL 7035) with the texture of shagreen leather Hidden fasteners Two easily removable rear screens (RAL 7035) and one non-removable (RAL 5023) Adjustable supports (0-40 mm)

The vacuum drying cabinet SHSV-65/7-I2PV is designed for drying and heating various materials in air and in vacuum at temperatures up to 700 ° C.

NV-1200 O are relatively small island tables with a superstructure. Such a table can be placed in the center of the laboratory and workplaces can be organized on its two sides. Table top depth: 152 cm. The table is designed for standing work: the height of the table top is 85 cm. A lamp and two sockets are built into the superstructure on each side. External dimensions of the table (W×D×H): 1218×1520×1650 mm. Work surface for your tasks We offer tables with various work surfaces. Table Model: Tabletop NV-1200 OL: Laminate. It is relatively moisture-resistant, resistant to short-term exposure to acids, alkalis and organic solvents. This countertop does not tolerate strong heating or prolonged exposure to solvents, concentrated acids and alkalis. NV-1200 OK: Porcelain tile. It is a practical solution for most chemical, biological, medical laboratories and workshops. You can put drying cabinets, baths and other heating devices on it. NV-1200 OSB: Chemically resistant plastic. It is a good choice for training workshops, analytical and medical laboratories. It does not tolerate high temperatures, heating devices should not be placed on the surface. NV-1200 OP: Polypropylene. It is chemically resistant, being a specialized solution for chemical laboratories that work a lot with concentrated inorganic acids and alkalis. It is not resistant to high temperatures. A table for convenient work in the laboratory The superstructure allows you to compactly place the necessary reagents and laboratory utensils next to the workplace. Its depth is 30 cm, and its height is 80 cm. The working area on each side is illuminated by a fluorescent lamp (included in the package). The switch is located on the left-hand side of the superstructure. There are also two sockets, one of which is grounded. The sockets (with two on each side, there are four of them in total) have the IP20 degree of protection, maximum load: 1.5 kW. A cabinet with three pull-out drawers is built into the table on each side. You can store there laboratory utensils or small stuff you need at hand. The side laminated panels of the table (chipboard 16 mm thick) are edged on the facade with a 2 mm PVC edge, which increases their impact resistance and mechanical strength. The legs of the table are adjustable in height within two centimeters, allowing you to place it even on a rther uneven floor.