Search

Bottles are used to protect the basic properties of chemical, pharmaceutical and other liquid, paste-like, mixed fluid products. Designed for scientific research. Not intended for medical use. Bottle: low density polyethylene (LDPE). Cover: polypropylene (polypropylene copolymers). The addition of a nucleator (illuminator) is allowed for greater hardness (if necessary).

The drying cabinet with manual vacuum adjustment SNVS-90/5 (or SNVS-4,3.4,3.4.9/5) is designed for heat treatment of materials at temperatures up to 500 ° C with air access and in a vacuum controlled by manual valves.

Capacity, l/h 25,0 (-10%) Purpose preparation of distilled water of type 2 according to GOST 52501-2005 "Water for laboratory analysis" FS.2.2.0019.18 "Water for injection" Heating elements Heating element 2.7 kW 220V (stainless steel) – 6 pcs. The quality of the produced water GOST 52501-2005 "Water for laboratory analysis", FS.2.2.0019.18 "Water for injection" Type of current, frequency, three-phase alternating voltage, 50 Hz, 380 V Power consumption, kW 16.3 Overall dimensions (L×W×C), mm 660x550x760 Weight, kg 50,0

The locker is designed for storing clothes in the changing rooms of industrial enterprises, medical institutions, educational institutions and other facilities. The design is based on a painted aluminum profile. Doors and other locker elements are made of moisture-resistant HPL-plastic. The materials used ensure the strength and durability of the product, are not afraid of moisture, and are suitable for sanitization with disinfectants. Width - 400

BASIC EQUIPMENT The base is a collapsible frame made of rectangular steel profile, painted with powder paint (RAL 7035) with the texture of shagreen leather Hidden fasteners Two easily removable rear screens (RAL 7035) and one non-removable (RAL 5023) Rear side boxes Adjustable supports (0-40 mm)

Vacuum drying cabinet model SNVS-155/3,5-I2-RT-N with a volume of 155 liters of special design with a chamber width of 630 mm., with manual vacuum adjustment from the back of the chamber for heat treatment at temperatures up to 350 degrees.

The LOIP LT-224b modification device consists of an immersion thermostat-circulator LOIP LT-200 and a working bath with a lean-to hinged lid. Technical specifications: Temperature range: without external cooling, °C Current+10 ... +200 with tap water cooling °C Tvods+5 ...+200 Accuracy of temperature maintenance, °C ± 0.1 The error of setting the set temperature, no more than ° C ± 0.2 Heater power, W 2000 Pump: max. flow rate, l/min 10.5 pressure, 0.27 bar Bath volume, l 24 The working fluid is water, water-glycerin mixture, silicone oil. Open part of the bath / depth, mm 360x296/200 Overall dimensions, mm 535x335x420 Weight, kg 14.2

ConFlat (CF) standard connections are used to ensure the connection of components of vacuum systems operating in the field of high and ultra-high vacuum.

The working condition of the ND-500 diffusion pump depends on the temperature of the working fluid in the pump boiler. During the initial filling, it is recommended to fill the maximum volume of the working fluid. Working fluid is "VACMA OIL 500" vacuum oil (under technical specifications TU 19.20.29-061-00218526-2019). The total amount of working fluid in the ND-500 diffusion pump is a maximum of 5.5 liters, a minimum of 4 liters. The viewing window for visual inspection of the working fluid has marks of its maximum and minimum amounts. During normal operation of the pump, the level of the working fluid practically does not change.The temperature of the working fluid when the pump is operating at the maximum residual pressure is about 240°C to 255°C. It is recommended to monitor the operation of the heaters in the ND-500 diffusion pump using one temperature sensor. The temperature sensor must be installed in a special radiator socket above the heater. If there is a loss of working fluid and an increase in the temperature of the radiators of the ND-500 diffusion pump up to 320°C, the temperature sensor should give the command to automatically turn off the heaters. The subsequent activation of the pump heaters should not be automatic and should be carried out only after cooling the system. Water at the inlet to the cooling systems of the housing and the oil reflector must be supplied with a pressure of 0.3 MPa (3 kgf/cm2) to 0.5 MPa (5 kgf/cm2) and a temperature of plus 4 ° C to plus 25 ° C. The recommended cooling water consumption for the housing is 500 l/h, for the oil reflector it is 50 l / h. It is regulated by the outlet water temperature, which should not exceed plus 40°C. The water drain should be free (with a jet break). The required speed of action of pre-vacuum pumps at a pressure of 26 Pa (0.2 mm Hg.st) in the outlet section of the ND-500 diffusion pump should be at least 42 l/s. To reduce the losses of the working fluid of the ND-500 diffusion pump at pressures (1·10-1- 1) Pa [(7,5·10-4- 7,5·10-3) mmHg] it is recommended to install an additional LP-500 flow-through water trap on the outlet flange.

Capacity: 10.0 (-10%) l/h Volume of the built-in water collector: 20 l Heating elements: Heating element 2.4 kW 220V (stainless steel) – 3 pcs. The quality of the produced water: GOST R 58144-2018 "Distilled water", FS.2.2.0019.18 "Water for injection" Type of current, frequency, voltage: alternating three-phase, 50 Hz, 380 V Power consumption: 7.2 kW Overall dimensions (L×W×C), mm: 425×425×775 Weight: 22.8 kg Warranty period: 24 months from the date of sale Registration certificate for a medical device No. FSR 2010/07649 of November 01 , 2016 Electrical conductivity of the produced water: 2-2.5 microns/cm The temperature of the produced water: from 70 to 85 ° C Source water flow rate (at 10 °C water temperature): 75 (±10%) l/h Source water pressure: 0.1-0.4 MPa Version: Desktop with adjustable supports. Wall mounting is possible Coefficient of water purification from radionuclides: at least 4000 Service life: at least 10 years

Furniture for laboratory work. Table-sink LAB-M MO 150.65.90 PP Width, mm: 1500 Depth, mm: 650 Height, mm: 900 Equipment: The table top is polypropylene with an overhead rim around the perimeter. Attention! It is not recommended to use a polypropylene bowl for working with oil and petroleum products (fuel oil, bitumen, etc.) . The location of the bowl in the center, the mounting of the bowl is suspended. Inner bowl size – 400*400*300 mm The base of the sink table is a support pedestal made of white melamine Facades – laminated MDF of white color with a thickness of 16 mm, dark gray ABS edging Without shelves

Furniture for laboratory work. Table-sink LAB-M MD 150.65.90 PP Width, mm: 1500 Depth, mm: 650 Height, mm: 900 Equipment: The table top is polypropylene with an overhead rim around the perimeter. Attention! It is not recommended to use 2 polypropylene Bowls for work with oil and petroleum products (fuel oil, bitumen, etc.) . Hanging bowl attachment The inner size of each bowl – 400*400*300 mm The base of the sink table is a support pedestal made of white melamine Facades – laminated MDF of white color with a thickness of 16 mm, dark gray ABS edging Without shelves